Search Documents

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By R. J. Pindred

Discussion by R.J. Pindred In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea. CAPM shortcomings [The CAPM, as Davis stated, is expressed in the equation: ri=rf+pi4) where ri is the project discount rate rf is the risk free interest rate (3i is the project beta, and 0 is the market risk premium (rm - rf)] Application of the CAPM is more difficult than Davis indicates. Valuation is prospective, while the CAPM parameters are historical. Beta is determined from a regression analysis of historical data, while the beta needed for valuation is the expected beta. Betas are known to be unstable and the regressions that generate them often have low explanatory power. The difficulty of estimating a "project" beta must also be considered. Thus, the beta that is used in the CAPM will be based on the analyst's judgment. Like Cavender's discount rate, this judgment can lead to different project NPVs. Subjectivity in valuation cannot be avoided by a mechanical application of the CAPM. The risk-free rate, which Davis identifies as a short-term real rate of 4%, is also subject to scrutiny. A mining project is not a short-term investment and no single risk-free rate is appropriate for all of the cash flows. The hypothetical mine discussed in Cavender's paper is a six-year project. One might argue for the application of a risk-free rate from the Treasury yield curve at the duration of the project (in a bond-duration sense). This, too, is inappropriate. The risk-free rate should be matched to the timing of the cash flow. These rates can be determined by calculating the implied forward rates from the yield curve using a procedure known as "bootstrapping." It is likely that each of the project's cash flows would be discounted at a different rate. Commodity prices Davis criticizes the "ad hoc adjustment to the discount rate." Yet, in his discussion of the value of stochastic simulation, he suggests that the gold price be modeled as a "random walk, with or without a trend." This is essentially an arbitrary modeling of price risk. Consider that a liquid market in gold futures exists. The futures' price curve, which is closely related to the market's estimate of future spot gold prices, should be used to provide inputs to the model. This is especially true of a relatively short six-year project. Alternatively, as Davis correctly points out, a risk-averse investor can sell the commodity short to hedge price risk. Is it any more correct, in the portfolio sense, to account for price risk at all ?? References Cavender, B., 1992, "Determination of the optimum lifetime of a mining project using discounted cash flow and option pricing techniques," Mining Engineering, Vol. 44, No. 10, pp.1262-1268 Fabozzi, F.J., 1993, Bond Markets, Analysis and Strategies, Second Edition, Prentice Hall, Inc. Higgins, R.C., 1992, Analysis for Financial Management, Third Edition, Richard D. Irwin, Inc. Solnik, B., 1991, International Investments, Second Edition, Addison Wesley Reply by G.A. Davis Pindred discusses two issues related to my paper, the shortcomings of the Capital Asset Pricing Model (CAPM) and which commodity price values to use in the valuation exercise. Even though these topics are not directly related to the use or misuse of Monte Carlo simulation, they are important points to take into consideration in valuation exercises. Since I do not appear to have addressed these issues satisfactorily in my original paper, I will comment on each here. Pindred agrees with me that applying portfolio theory, and specifically the CAPM, to the selection of project discount rates is more defensible than ad hoc methods. But he then points out that the application of the CAPM to project valuation is more difficult that I indicate. It is true that the CAPM is a difficult tool for project valuation in general,. But the application of the CAPM to mining projects is one of the easiest I can think of. The biggest problem with using the CAPM for project valuation is coming up with an expected project beta. I suggest a project beta for gold projects of 0.45. The "true" value might be 0.35, 0.55 or whatever. Pindred correctly notes that the selection of the appropriate project beta is based

Jan 1, 1996

By Changhong Huang, Y. J. Wang

Proceedings of the 6th US Mine Ventilation Symposium SME, Littleton, CO, 1993, pp. 153-161.

Jan 1, 1995

By E. J. Berentsen, R. F. Nanna, D. Dell’ Elce, R. Lougheed

Apollo Gold’s Black Fox project is located 10 km (6.2 miles) east of Matheson, Ontario, Canada, on Hwy 101 East It is located within the prolific Destor Porcupine Fault Zone, which is also the host for the Dome and Hollmger mines to the west and the Holt and Holloway mines to the east. The local host rocks are intensely deformed and carbonized ultramafic volcanics, pillow basalts, syenitic felsic intrusives and argillaceous sediments. Gold occurs with pyrite and as spectacular specimens in native form. Past production accounted for a total of 195,337 oz (6,075,606 g) of gold. Apollo Gold Exploration, Inc. is conducting an intense drilling program aimed at expanding the reserve base.

Jan 1, 2004

By Martin N. Kelley

The Great Belt Link is a $3.5 billion fixed link across an 18 km (12 mile) wide body of water that separates the island of Zealand, on which Copenhagen is situated, and the main land mass of Denmark, Jutland, which is part of the European continent. The project consists of three main contracts. The first contract is an 8 km (5 mile) long, two-bore railway tunnel for the eastern half, the second contract is a 6.6 km (4 mile) combination railroad and highway bridge for the western half, and the third contract is a 6.7 km (4 mile) long high-level highway bridge for the eastern half. This paper will discuss the Eastern Railway Tunnel Project and the methods of construction that the joint venture consortium plans to use, along with its equipment selection. The ground conditions to be encountered begin with glacial tills, which are a mixture of clay, silt, sand, gravel, cobbles, and granitic boulders. The boulders can be up to 1-3 m (3-10 ft) in diameter. Underlying the till is a marl which is sometimes highly fractured with hydrostatic pressures of up to 8 bar. About 40% of the tunnel is in till and 40% in marl, with the remaining 20% being a mixed face of the two formations.

Jan 1, 1991

By Susan T. Bagley, Kenneth L. Rubow, David H. Carlson, Bruce K. Cantrell, Winthrop F. Watts

Permissible exposure limits (PELs) have been established for gaseous pollutants, carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), nitrogen dioxide (NO2), and some gas-phase hydrocarbons emitted in diesel exhaust. There is, as yet, no PEL recommended for diesel exhaust aerosol (DEA), nor is there a standard method for sampling this aerosol. The University of Minnesota and the U.S. Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size-selective inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were made in underground coal mines that use diesel equipment. The mine mean DEA concentrations for the five mines surveyed, determined with the PDEAS in the haulageway, was 0.89 mg/m3 with a standard deviation of 0.44 mg/m3. DEA contributed 52 % of the respirable aerosol at this location. In three of the mines filter samples were collected for DEAassociated polynuclear aromatic hydrocarbons (PAHs) and biological activity determinations. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust. In general, the PAH and biological activity levels were similar for all three mines, and indicate that up to 25 % of the haulageway concentrations may be contributed by outby diesel vehicles. Measured concentrations of CO, C02, NO, NO2, and SO2, were well below regulated levels. INTRODUCTION Diesel exhaust contains pollutant gases, such as carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and gas-phase hydrocarbons, as well as DEA. Much of the health-related concern focuses on DEA and associated organic compounds (Watts, 1992a). A wide variety of these PAHs have been identified and some are known carcinogens and/or mutagens. The U.S. Mine Safety and Health Administration (MSHA) has proposed new PELs for these and other contaminants (MSHA, 1989). MSHA has also published an advance notice of proposed rulemaking to establish a separate PEL for diesel particulate (MSHA, 1992). The U.S. Bureau of Mines has collaborated with the University of Minnesota to develop and field test a PDEAS. The PDEAS is a three stage sampler based on the MSA' personal respirable dust sampler. It utilizes a respirable cyclone preclassifier followed by a 0.8 µm cut point impactor and afterfilter operating at a flow rate of 2 L/min. Respirable aerosol greater than 0.8, µm in size is collected by the impactor while DEA, less than 0.8 µm in size, is collected by the afterfilter. Hence, gravimetric analysis of the afterfilter permits measurement of DEA concentrations. This development and laboratory evaluation of the PDEAS were described previously by Cantrell (1990) and Rubow (1990). During field tests of the sampler, numerous air quality measurements were made in continuous miner sections of five underground coal mines that use diesel haulage equipment. These air quality measurements included levels of selected PAH and biological activity associated with DEA collected in the intake and haulageway areas of three of the five underground mines, and CO, CO2, NO, and NO2 in two of the mines. The objectives of this paper are to present the DEA and associated pollutant concentrations measured in these mines and to assess the impact of diesel face-haulage equipment on underground mine air quality. MINE DESCRIPTIONS The mines used for the PDEAS evaluation were designated J, K, L, N, and 0. Mines K, N, and 0 are located in the Western United States, while mines J and L are located in the East. Each mine produces high volatile, bituminous coal with shift production levels varying from 500 to 2000 tons/section. Seam heights varied from 1.5 to 3.0 m. Mines K and N use continuous mining to develop longwall panels. The others are strictly room-and-pillar operations using continuous miners. The number and types of diesel-powered vehicles used at these mines were described by Watts (1992b). Mines J, K, N, and 0 use diesel power to assist in a wide range of activities in addition to coal haulage. These included road maintenance, personnel and materials transport, lubrication, and welding. Mine L used only three diesel-powered shuttle cars to haul coal. SAMPLING AND ANALYSIS METHODS Aerosol Measurements Aerosol samples were collected in the mine portal area, the clean air intake to the continuous miner section, the haulageway one crosscut inby from the feeder breaker and belt, in the return airway, and on selected personnel. The haulageway sampling site was located near the point where the diesel-powered shuttle cars turn around to dump their loads. Additional respirable and DEA samples were collected and have been reported by Haney (1990).

Jan 1, 1993

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

A Directory of Computer Programs Applicable to US Mining Practices and Problems. A. L. Sanford, T. L. Myers, and J. F. Stiehr. USBM OFR 131-78, Nov. 1977. A Master Environmental Control and Mine System Design Simulator for Underground Coal Mining. Tape MDS-5. Pennsylvania State University. USBM CT 1.77, Dec. 1975. Contains computer programs on a dynamic general purpose computer simulation model for underground coal mining. A Method for Computing Stabilization Pressures for Excavations in Incompetent Rock. J. D. Dixon and M. A. Mahtab. USBM RI 8128, 1976. Describes technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. Accident Cost Indicator Model to Estimate Costs to Industry and Society From Work-Related Injuries and Deaths in Underground Coal Mining. Vol. I.III. D. G. DiCanio, A. H. Nakata, D. Colvert, and E. G. LaVeque. OFR 39(1)(3)-77, Dec. 1976. Describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents In underground coal mines. An Interactive Computer System for Evaluating Coal Mine Illumination. R. Goldstein. USBM OFR 110-80, March 1980. Computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights. Analytical Modeling of Mine Roof Behavior Using Statistical Material Properties. R. T. Langland and F. J. Tokarz. USBM UCRL-51876, Aug. 1975. Analytical study of coal mine roof behavior using a computer model of a room-and-pillar mining method. Application of a Total System Surface Mine Simulator to Coal Stripping. Vol. I-VII. Pennsylvania State University. USBM OFR 33(1)(7)-78, Aug. 1978. Describes model development, input and output documentation, three case studies of an open-pit materials handling simulator, and development of two equipment selection models and a cost model. Characterization of the Structural Behavior of Rock Masses. Vol. I-II. L. R. Herrmann and M. A. Taylor. USBM OFR 67(1X2)-75, Sept. 1974. Computer subroutines for characterization of rock behavior, Including variability of properties within the rock mass, planes of weakness orthotropy, strength criteria, and post-failure behavior. Coal Mine Electrical System Evaluation. Vol. I-VII, L. A. Morley, et al. USBM OFF! 61(1)(7)-78, 1977. A concept to improve underground coal mine electrical system safety and availability. This proposed technique is based upon the ability to predict incipient failures in the mine power system. Prediction is made possible by a new method which uses a minicomputer to implement pattern recognition algorithms. Computer Modeling of Fluid Flow During Production and Environmental Restoration Phases of In Situ Uranium Leaching. R. D. Schmidt. USBM RI 8479, 1980. Describes development and application of a computer model for simulating the hydrological activity associated with in situ leaching. Interpretation of Rock Mechanics Data, Vol. II (A Guide to Using UTAH2). W. G. Pariseau. USBM OFR 47(2)-80, June 1978. Brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis. Iterative Approximation Techniques for Microseismic Source Location. G. H. Dechman and Meng-Cherng Sun. USBM RI 8254, 1977. Iterative approximation method for microseismic source location developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems such as slope failure in an open-pit mine. Limits and Cost Sensitivity of Alternative Parting Handling Methods. Vol. I-II. T. E. Finch, D. R. Haley, and C. J. Speaks, Jr. USBM OFF! 117(1)(2)-77, March 1977. Programs to examine alternative methods of handling the parting between two coal seams in a surface mining operation. Alternative methods consist of equipment implementation in either a stowing or haulback technique. Methane-Water Flow in Coalbeds. H. S. Price. USBM CT 1-79, April 1972. This computer program calculates transient, two-dimensional, gas¬water flow in a porous medium. Plastic Canopy-A Computer Program for the Structural Analysis of Protective Canopies. K. D. Winters, G. A. Gavan, and J. C. Ault. USBM IC 8795, 1979. Presents a FORTRAN IV program for the structural analysis of protective canopies used In underground mines and rollover protective structures used in surface mines. The Three-Dimensional Structural Analysis of Double-Entry and Single-Entry Coal Mines. Vol. I-III. Agbabia Associates. USBM OFF 16(1)(3)-80, Oct. 1978. Describes the computer program designed to perform a three-dimensional finite element analysis of an instrumented section of double- and single-entry coal mines. Underground Mine Evacuation Plans Analyzed by Computers. D. Tesarik, D. Nicholson, and A. B. Boghani. MSHA, Vol. 4, No. 5, Oct. 1979. USBM has developed a computer program to evaluate and construct mine evacuation procedures and plans.

Jan 11, 1981

By A. Unal

Barbaro et al. (1990) implemented a tedious study aimed at delineating the short-scale spatial variability of sulfur in a coal seam. It is not possible, however, to extend their conclusions to any other coal seam or use theirs in any other fashion, because the background geology was not presented. Nor were the conclusions accompanied by geological interpretations in the paper. In addition, an unfortunate printing error occurred where the total sulfur (determined by High Temperature Combustion) variogram in Fig.3 was duplicated in Fig. 2 instead of the seam height variogram. A more serious error, however, has been committed in the definition of the variable, seam height. What is defined as seam height by Barbaro et al. (1990) is, in essence, mining height, and is not a regionalized variable that should be studied by geostatistical methods directly. Despite the fact that the variable, seam height, is not defined in the paper explicitly, the following quotation discloses the fallacy: "All roof rock that exceeded 1.8 m (6 ft) from the floor was not taken because the longwall was operated to not mine more than 1.8 m (6 ft) unless the coal seam height exceeded 1.8 m (6 ft)." From this definition, the seam height, and therefore the sampling height, is equal to the actual coal thickness, if the coal thickness is greater than 1.8 m (6 ft). Otherwise, it is equal to the sum of the coal thickness plus the thickness of the roof rock that complements the thickness to 1.8 m (6 ft). In the latter case, the seam height is constant and equal to 1.8 m (6 ft). It is possible to conduct a variogram study on a pool of samples that are realizations of two different variables. But the conclusions derived would not belong to any one of the two variables uniquely and, therefore, do not possess any significance. Geostatistical analysis is irrelevant for the sum of multiple regionalized variables formed by arbitrary selections. In a two¬seam setting, for example, the mining height, as defined by the thickness of one seam at one location and the thickness of both seams at another location (due to quality and/or minimum thickness considerations perhaps), should not be used in the calculation of one common variogram. The two seams should be modeled separately. They can then be combined according to the specific purposes of the study. On the other hand, if a constant is added to a regionalized variable (to incorporate dilution perhaps), the variogram of the new variable will not change. Barbaro et al.( 1990), surprisingly, does not give any geologi¬cal interpretation of their results despite the fact that most of them can be explained by the origins of sulfur in a coal seam. The presentation of the results of a geostatistical study with no reference to the geology of the deposit is uninformative. It may also be misleading for the potential users of geostatistics. It is not unusual to find nuggets of pyrite in coal seams. In such cases, pyritic sulfur will probably display a spatial structure for only a very small distance that will appear in the experimen-

Jan 1, 1991

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By J. A. Dos Santos

High angle conveyor (HAC®) systems in open pit mining offer many advantages over the traditional, truck only, haulage systems, including: (1) superior energy efficiency, (2) less dependency on petroleum products, (3) less sensitivity to inflation, (4) less labor, (5) less excavation for the amount of ore recovered, and (6) less ramp construction and maintenance costs. Previous studies had revealed the technical and economic feasibility of high angle conveyors. This paper presents the Sandwich Belt HAC® as the vital link to optimization of in-pit conveying systems. HAC development to date is discussed, beginning with studies in 1979, to the first large scale prototype in 1983, to the first commercial unit in 1984, into "the latest commercial installations. Discussion continues with the HAC systems to suit the various open pit mining operations and the corresponding characteristics of the system components, particularly the high angle conveyor. The range of HAC systems from the low capacity (up to 1,814 t/h), low lift (10.7 to 36.6M), highly mobile to the moderate capacity (1,814 to 3,629 t/h), moderate lift (36.6 to 76.2M), intermittently mobile to the high capacity (greater than 3,629 t/h), high lift (greater than 76.2M), semi-mobile, are discussed along with some possible combinations of these.

Jan 1, 1989

By Y. Guan

The dissolution behavior of silver in ammoniacal solutions with cupric ammine as an oxidant has been investigated using a rotating disc electrode. The rates of dissolution of silver were determined by an electrochemical means as well as a direct measurement of silver ions reported in the bulk solution as a function of time. The variables investigated included stirring speed, temperature, concentration of lixiviants, and pH of the solutions. The rate of dissolution under the conditions studied' was found to be controlled by an electrochemical reaction at the liquid/ solid interface with an apparent activation energy of 48.07 kJ /mole. The rate was found to be a half order with respect to the, concentration of cupric tetra-ammine, Cu(NH3)l+.; The results were explained in terms of a mixed' potential theory.

Jan 1, 1994

By F. J. Susko

The Bureau of Mines applied a flotation model to the hydrodynamics of the Bureau-developed rapid flotation system. Rapid flotation is a process which separates the bubble-particle attachment and froth-pulp separation stages of the flotation sequence into two discrete unit operations allowing the operations to be individually optimized. Both an air-injected hydrocyclone and an in-line mixer were used as the bubble-particle attachment unit and a shallow-depth froth separator was used to separate the ore-laden froth from the pulp. A 10-L/min batch system was tested on a coarse coal feed sample. The system was tested using two different bubble-particle attachment units at various aeration levels in order to test the flotation model. The results of the flotation model reflect general trends observed in the experimental data.

Jan 1, 1993

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By S. D. F. Rocha

The influence of surfactants on the crystallization of calcium sulfate was investigated in both hatch and continuous systems. The investigation was per formed at the following conditions. 343 °K, 28% P205 and with a sulfate level of 2.0%. At concentrations of 5 and 200 µgig, respectively, dodecylbenzene sulfonic acid (DBSH) and sodium diisooctil sulosuccinate (SSNa) promoted both an increase in the size and a reduction in the length/width (L/W) ratio of the calcium sulfate hydrates produced in the hatch and continuous crystallizers. Unique effects were observed in the batch system at higher DBSH concentrations. At 10 µg/g, the precipitation of hemihydrate crystals with a distinct morphology and texture occurred under conditions where dihydrate precipitation was expected. Above 50 µg/g, the precipitation of calcium sulfate hydrates was completely inhibited.

Jan 1, 1996

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By L. G. Austin, R. S. C. Rogers

INTRODUCTION Coal is geologically a sedimentary rock with distinct bedding planes containing a mixture of petrographic constituents. Yet. because of its chemical nature, it also has some of the characteristics of a polymeric material. In addition, it is extensively precracked to give a macropore structure and also has a substantial internal volume of microporosity. Add to this the mineral constituents dispersed in the coal in a variety of forms and sizes. and it can be readily appreciated that coal is a complex and heterogeneous material. It has to date not been possible to predict the particle size distributions produced by breakage of coals from a priori application of the principles of fracture mechanics. However, there is a substantial body of data resulting from empirical observation of size distributions produced under various conditions, primarily from grinding mills. It is the function of this review to outline how this empirical information can be used to predict product size distributions for those systems which have been studied systematically, and to suggest future avenues of research using similar methodology. FRACTURE THEORY APPLIED TO COAL It is, of course, possible to devise experiments for slow crack propagation in a coal. However, the evidence is that coal breaks by brittle fracture in the mills and mining machines of industrial importance and therefore the theory of brittle fracture is sufficient to illustrate the important features of the fracture of coal. In order to produce size reduction a solid must be stressed by the application of force. The force can be a tensile (stretching), compressive, or shear force, and the three dimensional stress pattern in the solid represents the tensile, compressive, and shear forces per unit area acting in any direction through any point in the solid. As an illustration consider the case of a simple one-dimensional tensile stress: then stress is defined as a=F/A where F is the force. A is the cross-sectional area of the solid normal to F and strain. E, is defined as the fractional change in the length of the solid. so that E= x/L where x is the extension of an original length of L. Coal behaves as an elastic material over short times (although viscoelastic creep can occur if the stress is maintained over long times) and if it is not stretched too far the coal returns to its original shape when the stress is removed; otherwise catastrophic failure occurs and the coal fractures at a stress termed the tensile strength. The failure under stress of an elastic material is termed brittle fracture. Elastic material fails at small stain and the stress-stain relation to where brittle fracture occurs is the empirical Hooke's law. a= YE, where Y is Young's modulus. The work done on the solid to take the solid from zero external stress to a stressed state by slowly increasing F up to a final stress u is the integral of the stress times the strain. This reversible strain energy is stored in the solid and. using Hooke's law. is u /2Y per unit volume of solid. If the solid is immediately loaded to u the work done is [EAuL] which Is a2 /Y per unit volume, that is, twice the reversible work.

Jan 1, 1988

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

By Y. Okahara

The chlorination behaviors of pure iron and manganese oxides were investigated by combining a thermogravimetric analysis (TGA) technique with batch-boat roasting followed by leaching. Ferrous and manganeus oxides could be chlorinated readily, but, in the absence of a reductant, the higher oxides of both iron and manganese were difficult to chlorinate. Thermogravimetric analysis curves were drawn to illustrate the complexitites of the reactions, and the possible mechanisms were discussed. Then three manganiferous materials from the Cuyuna Range of Minnesota were treated by a process involving the selective chlorination of manganese followed by leaching. The results were interpreted in the light of the chlorination mechanisms observed on the pure iron and manganese oxides.

Jan 1, 1969