Search Documents

Allis Mineral Systems' Grate- Kiln system can economically convert low-grade iron ore into high- grade iron-ore pellets suitable as feed material for blast furnaces for making steel. These pellets can also be fed to a direct reduction process for making sponge iron. The Grate- Car system combines the company's [ ] Grate-Kiln system for iron-ore pelletizing and Accar system for iron- ore reduction. The Grate-Car system consists of a traveling grate, a ported rotary kiln and a rotary cooler that are coupled in series. This system eliminates the pelletizing plant's rotary kiln and annular cooler. It reduces the need for some auxiliary equipment. This results in lower capital cost and lower energy consumption. The traveling grate provides that static bed handling necessary for heat hardening pellets before their discharge into the kiln. The ported kiln provides the reducing atmosphere with a more precise means of controlling the kiln axial temperature profile than conventional rotary kilns.

Jan 1, 1997

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

By W. Choi

The present study revealed that the bioleachability of a chalcopyrite flotation concentrate is influenced by the semiconductor properties of CuFeS2. The overall reaction of biooxidation,

Jan 1, 1991

By Brett P. Spigarelli

"To meet the growing need for CO2 capture and storage technology, Michigan Technological University is studying CO2 capture using alkali-based solvents. The objective of the present study was to find a way to increase the absorption rate of CO2 into an alkali solution without reducing the absorption capacity of the solution. One approach to increasing absorption rate is to use a surfactant to chemically alter the gas bubble size. The surfactant chosen for the study was a neutral-charge polypropylene glycol methyl ether (PPGME) with a molecular weight of 200. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations. Results showed that as the concentration of PPGME increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 x 10-3 mol/min CO2 at 0g/L PPGME to 3.92 x 10-3 mol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in the absorption capacity of the solution. IntroductionChemical absorption using an amine solvent is currently the most mature carbon capture and storage technology available. Amines are advantageous in that they have a fast CO2 absorption rate, which leads to a high CO2 removal efficiency. However, amine absorption has some considerable drawbacks, such as high energy requirements, high equipment corrosion rates, amine degradation in the presence of oxygen, high waste generation and a large increase in plant footprint if new equipment is constructed (Herzog and Golomb, 2004; D’Alessandro et al., 2010). Due to these drawbacks, Michigan Technological University (MTU) is studying CO2 absorption using alkali-based solvents, which address the above disadvantages of amine solvents."

Jan 1, 2015

By Richard R. Klimpel, Basil F. Fee

This paper summarizes the status of a series of new chemical reagents developed with the explicit goal of expanding the capabilities of existing froth flotation processes as well as allowing for new solid/solid separations to be undertaken that are not now feasible with flotation. The first portion of the paper briefly outlines the theory and motivation behind the development of each new reagent family. 'The second portion of the paper deals with specific laboratory examples of some separation systems studied to date.

Jan 1, 1993

The Janet Annenberg Hooker Hall of Geology, Gems and Minerals, located in the National Museum of Natural History, Smithsonian Institution, in Washington DC, opened in September, nine years after initial fundraising efforts were begun. The 1,858-m2 (20,000-sq ft), $16-million hall was mostly funded by private groups and individuals, including $1.7 million from 43 National Mining Associa¬tion (NMA) member companies. Companies that contributed more than $100,000 included Cyprus Amax, Phelps Dodge, Asarco, Homestake Mining, BHP, Caterpillar, Cleveland Cliffs, Exxon Coal and Minerals, Freeport-McMoRan, Newmont Mining and Peabody Holdings. The mining industry's contributions funded a walk-through Mine Gallery. It. features diora¬mas of four mines, as well as numerous specimens associated with the mines. The Mine Gal¬lery demonstrates to the public the importance of mining. The hall was named in honor of Hooker. She contributed $5 million in cash plus the Hooker Yellow Starburst Diamonds to the project. The hall is touted by the Smithsonian as the "most comprehensive earth science complex of its kind." It consists of seven galleries, each devoted to different aspects of gems, minerals and rocks. In addition to the Mine Gal¬lery, the hall contains a collection of gemstones and jewelry pieces, an extensive collection of minerals, a gallery devoted to plate tectonics and a gallery devoted to the moon, meteorites and the solar system. The new hall is a complete makeover of the old and outdated Geology Hall. It was built in the 1960s and finally closed to the public in 1995.

Jan 1, 1997

By L. M. Chan, D. H. Carlson, J. H. Johnson

This paper discusses laboratory evaluation of a tailpipe emissions measurement apparatus (EMA) developed by Michigan Technological University (MTU) under contract to the Bureau of Mines. The apparatus dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, C02, NO and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. During the preliminary laboratory evaluation concentrations of DPM, CO and CO2 were measured. The concentrations of CO and CO2 measured by the EMA were usually within ±14 pct of laboratory-measured values for CO and ±20 pct for CO2. EMA DPM concentrations correlated well (r = 0.96) with the laboratory values, but were 29 pct lower on average. The CO and C02 differences were observed to be related to the method of calculating the EMAs' dilution ratio and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminery analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1991

By Malcolm J. McPherson

Mine shafts that are used as primary ventilation routes are different in their airflow characteristics to other subsurface openings because of the aerodynamic effects of guide rails, buntons, pipes, cables, ropes, and shape, size and velocity of conveyances. As many shafts contribute heavily to the overall resistance of a mine ventilation circuit, it is important to be able to predict the resistance of a planned shaft with reasonable accuracy. This paper describes part of a study on the ventilation characteristics of hoisting shafts, conducted for the Basalt (Nuclear) Waste Isolation Program (BWIP). Methods of quantifying each of the four components of shaft resistance are developed; namely the shaft walls, fittings (buntons, pipes, etc.), the skips or conveyances, including the dynamic effects of their motion, and shaft stations. Practical guidance is given on ways of reducing the shaft resistance. The paper concludes by giving a step by step procedure for the ventilation aspects involved in the design of combined hoisting/ventilation shafts.

Jan 1, 1987

By Charles M. Brinckerhoff

Everyone -- especially the engineer -- is aware of the great technological and social changes taking place in our world today, We realize that changes have been taking place since man's beginnings on earth, but the element we now face is the speed of change, rather than change itself. Developments in medicine, in transportation, in space exploration, in global communications, and in many other fields, are constantly being made known. These developments are affecting the lives of each of us, although some may appear remote and unrelated to us as individuals. New developments, almost on a daily basis, affect our work as well as our social, religious and educational lives. The effects are immediate and permanent.

Jan 1, 1967

By Gemei Yang, Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

Laboratory tests on controlled airflow recirculation have shown the development of transient states in response to changes in system prevailing conditions such as those generated by a sudden start-up and stoppage of fans. Researchers in many European countries have developed various models to explain these phenomena. However, these models failed to consider some important factors such as diffusion and dispersion of gas in turbulent flows. For both in-line and cross-cut recirculation, tests have shown that after the start- up of a booster fan, the gas concentration in the system fluctuates, reaching high levels at the initial states and slowly dying out with time. These fluctuations cannot be represented adequately by simple step-wise functions but rather by smooth, albeit complex equations. In this paper, the phenomena are explained by the convection-dispersion theory, and represented by a mathematical model. Based on a few simplifications and applying Fourier's Transform Method to the differential equations of the flow recirculation model, an integral form of gas concentration function was derived. The Simpson Integration Method was used to compute numerical results for two laboratory tests. The paper also discusses the range of the dispersion coefficient to improve the accuracy of the model.

Jan 1, 1989

By A. Norholm

For grinding Portland Cement, the power consumption accounts for some 35 % of the total consumption of electrical energy for producing cement, counting right from the quarry to the packing plant. It is therefore for very good reason that great efforts during the past years have been put into making cement grinding more efficient, thereby saving power. In this paper three ways of reducing the consumption of electrical energy will be described, namely precrushing in the high pressure FLS-Köppern roller press, the introduction of a new design of COMBIDAN diaphragm in ball mills and the separation of mill discharge in the newly developed high efficient; separator SEPAX from F. L. Smidth.

Jan 1, 1987

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By Alfredo Valdivia, Hamed Nejad, Vincent Monaco, William Cao

"The East Side Access (ESA) CM005 Contract - Manhattan South Structures - consists of the installation of the waterproofing and final concrete lining for railroad tunnels, 3-Level Wye track turnout structures, segments of the Main Cavern Station, and a series of Ventilation Structures excavated beneath the existing Metro North Railroad (MNR) Grand Central Terminal. Several key team decisions made collectively by the Construction Manager (CM), Designer, and the Contractor has allowed the scheduled construction duration of 29 months to be maintained. These strategies include the use of alternate design and construction methods, including the use of pneumatically applied concrete lining and precast lining. This paper discusses these strategies, and illustrates how successful teamwork and cooperation during the execution of a large-scale construction project can lead to lowering costs, improving quality, and maintaining the overall project schedule. INTRODUCTION The East Side Access Project The Long Island Railroad (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already over congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodate the NJ Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the NYCT Subway System and Metro North Rail Road. The ESA Project includes building new tunnels and facilities under Manhattan and Queens. (See Figure 1).The Manhattan Alignment In the Manhattan segment of the ESA Project the excavation in hard rock of tunnels, cross passages, caverns and shafts has been completed by tunnel boring machines, drill and blast, and road header. The construction of the structural concrete final lining, interior structures and fit-out of the previously excavated caverns and tunnels are currently being performed under Contract CM005 Manhattan South Structures awarded to Michels Corporation and Contract CM006 Manhattan North Structures awarded to Frontier Kemper Constructors Inc. This paper focuses on the design and construction aspects of Contract CM005 which is the first ESA Contract in Manhattan to successfully construct concrete final linings in pre-existing excavated areas."

Jan 1, 2016

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By S. W. Asihene, K. Osseo-Asare

The leaching and solution treatment operations used in the ammoniacal treatment of laterites depend on the ability to establish and maintain close stability relations between soluble metal ammine complexes and solid phases such as oxides, hydroxides, basic carbonates, sulfides and ammonium double salts. This paper presents a quantitative treatment of heterogeneous equilibria in ammonia/laterite hydrometallurgical systems, by means of several.types of hydrometallurgical phasedia- grams (e.g., Eh-pH, log [NH3 + NH4+] - pH, log [C02] - pH, log SO42-] - pH, log [Metal] - pH). Dissolution/precipitation phenomena associated with nickel and cobalt recovery and with magnesium scaling are discussed in the context of the phase diagrams.

Jan 1, 1979

By Jr. Kirschner

An abandoned waste impoundment located within a portion of the Kellogg, Idaho Superfund site constitutes a field research area for studying the feasibility of recovering heavy metals in-situ from unsaturated mine and mill wastes. A prototype in-situ leaching cell has been evaluated using liquid-phase tracer tests and other hydro-geologic tests prior to introducing a lixiviant. The results of the tests suggest that: (1) the cell can be operated excursion-free with a low-density lixiviant at an injection/withdrawal rate of approximately 0.32 l/s; and (2) each hydro-geologic unit is highly heterogeneous at the different scales studied.

Jan 1, 1993

By S. K. Kawatra

The fly ash from coal combustion often has a high unburned-carbon content. This can make it unusable as a cement admixture, which is the major fly ash utilization market. As a result, high-carbon fly ashes currently disposed of by landfilling, at sometimes considerable expense. In this paper, the use of froth flotation to remove the unburned carbon from fly ash is described. Three different fly ashes were studied, which had Loss-on-Ignition (LOI) values of 6.79, 6.90, and 11.11 %. It was found that the use of an alkanolamide/oil mixture as a froth-conditioning reagent could greatly reduce the amount of collector needed, by increasing the affinity of the collector for oxidized carbonaceous surfaces. For each of the three fly ashes, froth flotation reduced the LOI of the ash to less than 2% which is well below the ASTM specification of no ' more than 6.0% LOI for Class F fly ash. Increasing carbon content of the ash tended to increase the quantities of reagents needed in flotation.

Jan 1, 1996

By Sam H. Patterson

The advances in knowledge of world bauxite resources in the last few decades include contributions to the geology of deposits, discovery of large resources, shifts in availability, and changes in. the industry in response to political and economic pressure. Improvements in the understanding of geology have resulted from the larger numbers of geologists working on bauxite and better exchanges of information. The large deposits discovered are mainly the laterite type in tropical regions. These discoveries have led to major increases in bauxite resource estimates as well as to shifts in bauxite availability and in the ranking of producing nations. Changes resulting from political, environmental, and economic pressures have resulted in increased costs of bauxite and in renewed interest in potential nonbauxite sources of aluminum. Aluminum is produced from nonbauxite raw materials only in the U.S.S.R.; however, research on extraction processes or investigations of nonbauxite alumina resources has taken place in several countries.

Jan 1, 1984

By A. B. Samaddar

A prototype automated mapping and spatial information management system has been developed, and illustrates how a powerful map manipulation capability and a comprehensive display system can be combined using both raster and vector mapping: The concept of a mapbase and information retrieval mechanism, query language as well as text and graphical menus, is introduced. The Geographic Information System (GIS), which has been built around a system for storage and retrieval of spatial and textual data, allows interaction with geographic space represented on a displayed map. The prototype is demonstrated using maps and information of an open pit mine.

Jan 1, 1989