Search Documents

By C. D. Harrison, J. W. Parkinson

This paper compares the ash slagging potential of Illinois No. 6 seam coal as raw coal, as commercially cleaned coal processed in a baum-jig plant, and as coal cleaned to a reduced ash specification at the Electric Power Research Institute's (EPRI) Coal Cleaning Test Facility. The comparison is based on ASTM ash fusibility data, a slagging index, gravity fractionation analyses of critical mineral matter compounds, and comparative pilot combustion tests. The first three grounds of comparison are laboratory data. The final comparison involves burning about 13.6 t (15 st) of each coal at Conoco's 4.40-kW/h (1.5 million-Btu per hr) test combustor. The evidence of these four comparisons indicates that lowering the ash specification of coal before combustion can significantly improve the ash slagging characteristics of Illinois No. 6 seam coal.

Jan 1, 1987

By P. R. A. Andrews

Areas of bubble contact were delineated for topaz and tourmaline in the presence of chloride, fluoride, sulfate, phosphate, oxalate, and citrate ions using dodecylamine hydrochloride collector. The limits of pH and the minimum collector concentration were established using the bubble pick-up technique. Bubble contact did not occur below the p.z.c. (point of zero charge), estimated to be 5.6 for topaz and 6.6 for tourmaline, in the presence of chloride ion. Flotation below the p.z.c. was, however, extended by citrate, oxalate, phosphate, sulfate, and fluoride ions. Oxalate, citrate, and fluoride ions displayed the greatest pH range of activation, followed by phosphate and sulfate ions. Chloride ion acted as an indifferent electrolyte. Topaz was selectively activated with respect to tourmaline by fluoride and phosphate ions. Topaz was activated by fluoride ion between pH 2.4 and 5.6. Tourmaline flotation in this pH range was virtually insignificant. Topaz was activated by phosphate ion between pH 4.9 and 7.4. Tourmaline flotation in this pH range was only partial. Activation appeared to be strongest when anionic protonated species were in maximum concentration. Strong activation also corresponded to very stable metal ion species thought to be formed on the surface of each mineral.

Jan 1, 1991

By S. J. Ripke

To pelletize fine moist magnetite concentrate, a 40% water slurry must be dewatered to about 10% by filtration, before it can be agglomerated into pellets. Slurry pH, typically ranging from 8 to 11, gives the magnetite particle surface a strong negative charge and thus causes two adverse effects. First, this negative charge attracts calcium and magnesium cations, which strongly retard the effectiveness of the bentonite clay binder added during agglomeration. Second, a repulsive force created by the negative charge functions as a dispersant that reduces filtering production rates. Tests were conducted to remove these cations during filtration, by rinsing the moisture remaining in the filter cake with a small amount of water adjusted to pH 6 with HCl. Laboratory work was also conducted at Michigan Technological University (MTU) and at Cliff’s Mining Services Company (CMSC) to corroborate the plant tests. In some cases HCl caused filter bag blinding, therefore CO2was investigated to reduce pH. The CMSC lab tests showed that using carbon dioxide to reduce slurry pH from 7.6 to 7.0 improved filtering production rates by 11%. Plant-scale filtering rates were improved by 23.7% when carbon dioxide addition reduced the slurry pH from 8.6 to 6.7.

Jan 1, 2004

By J. R. Johnson, C. G. Stewart, D. K. Myers

INTRODUCTION Radon-222 is an inert, radioactive gas formed by the radioactive decay of radium-226, a long-lived member of the uranium-238 decay chain. Radium is present in varying amounts in virtually all soils and, on the average, about 36,000 pCi (1330 Bq) of radon per square meter of soil diffuse into the atmosphere each day (UN 1977). Radon decays with a half-life of 3.6 days through four short-lived daughters to lead210 and it is these short-lived daughters[ [Ra A, (218Po, t, = 3.0 min) , Ra B, (214 Pb, t;, = 27 min), Ra C, (214Bi, t] = 20 min) and Ra C1 (214Po, t] = 2.5 x 10-6 min)] ]which cause the major health hazard associated with radon (Bale 1951). Atoms of these daughters, either unattached or attached to the ever-present particles in air, are deposited on the surfaces of the respiratory tract; alpha particles emitted in their decay can result in large doses to the cells of the bronchial epithelium lining the respiratory tract. These daughters will be present in air in varying relative concentrations depending on the "age" of the air (time since radon emanated into it) and on the amount of mixing of radon and radon daughter contaminated air with clean air. [The practical unit developed to quantify the amount of radon daughters in air is the Working Level (WL). This unit was historically related to the equilibrium concentration of 100 pCi (3.7 Bq) of the short-lived daughters of radon in one liter of air (cf. Holaday 1969) and is defined as any mixture of the short-lived daughters in a liter of air that have a-potential alpha energy of 1.3 x 105 Mev (2.08 x 10-5J) in their decay to lead-210. The working level month (WLM) was developed along with the WL, and was defined as an exposure to one WL for a working month (170 h). This is equivalent to 2.2 x 107 MeV•h•L-1 (3.54 x 10-3 J.h.m-3). If the average breathing rate is taken as 1.2 m3.h•1 (ICRP 1975), then one WLM is equivalent to inhalation of 4.24 mJ of potential alpha energy.] It is now generally agreed that the inhalation of radon daughters is the major potential radiation hazard in uranium mining, and contributes a substantial fraction to the natural radiation exposure of the general population due to the accumulation of radon and radon daughters from natural sources in buildings. Radon daughter concentrations in modern mines are controlled by ventilation, and by blocking off old working areas (cf. Simpson, 1959). However, before the hazard from radon daughters was recognized, considerably higher concentrations of radon daughters were present in some uranium and non-uranium mines. These high radon daughter concentrations resulted in an increase in lung cancers in the mining population, and it is these results that are our main source of information on the risk of inhaling radon daughters. HISTORICAL REVIEW Many excellent reviews of the history of understanding the health effects of inhalation of radon daughters are available (see, for example, Hueper 1942, Lorenz 1944, Sikl 1950, Stewart 1964, Holaday 1969, Lundin 1971, Cross 1979) but a brief summary of some of the highlights in this area may be of interest. [a] 1556: Agricola describes an unusual and fatal chest disease occurring among underground miners in the region of Schneeberg and Joachimsthal (Jachymov) in the Erz mountains in Central Europe. (It is of some historical interest to note that Agricola's book was translated from Latin into English by a mining engineer and his wife; the engineer later became President of the U.S.A.) [b] 1879: Haerting and Hesse indicated that the majority of deaths among Schneeberg miners were due to lung cancer; the lung cancers in these miners (who were incidentally not cigarette smokers) were observed twenty to fifty years after they began working in the mines. [c] 1896: Discovery of natural radioactivity by Becquerel, followed by discovery of radon by Dorn in 1900. [d] 1924: Ludewig and Lorenser report high concentrations (400 - 15000 pCi or 15 - 570 Bq per liter) of radon in the air in the Schneeberg mines and suggest that radon could be responsible for the high rate of lung cancer among miners. However, the reason why radon should cause lung cancer specifically was still not really understood up to twenty years later (Lorenz 1944). High concentrations of radon in the air in the Joachimsthal mines were reported by Behounek in 1927 and a high incidence of lung cancer among Joachimsthal miners (similar to that among miners at Schneeberg, which is only some 30 km distant but in a different political district) was noted at about the same time (Sikl 1930; cf. Sikl 1950). It is estimated that about half of the Joachimsthal miners died from lung cancer and about half from silicosis and tuberculosis (Sikl 1950). [e] 1930's and 1940's: Radioactive ores are deliberately mined in the U.S.A., Canada and other countries primarily as a source of radium for medical purposes and for luminescent dials; other radioactive ores are mined as a source of several non-radioactive minerals, while extensive uranium mining did not begin until the late 1940's. [f] 1940: Based on crude epidemiology and dose calculations, Evans and Goodman propose 10 pCi L-1 as a maximum permissible concentration of radon in continued human exposure. This is the first known recommended maximum permissible concentration for radon. This recommendation was adopted by the U.S. National Bureau of Standards in 1941 and reconfirmed in 1953. [g] 1945: Mitchell identifies the short-lived daughters in radon as a likely cause of the increased lung cancers in the Schneeberg-Joachimsthal miners

Jan 1, 1981

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By William H. Wiese

Anecdotal reports of high rates of congenital malformations and spontaneous abortions at the Shiprock Indian Health Service Hospital in San Juan County, New Mexico prompted an interview survey, obtaining data from families of 26 former uranium miners and 30 controls. Results supported the possibility of increased fetal wastage and congenital malformations. However, definitive conclusions were obviated by methodologic limitations in terms of selection of cases and controls and interviewing technique, as well as very low numbers and lack of statistical significance. The Council of Environmental Quality (1980) published a report which singled out San Juan County, nationally, as having an extra-ordinary high rate of congenital anomalies reported from birth certificates in the years 1973-75. San Juan County is in the northwest corner of New Mexico and includes the northeastern edge of the Navajo Indian Reservation. It has been the site of uranium mining and milling and also of coal mining (Clement Associates, 1980). While much attention has been focused on lung cancer and chronic lung disease as health hazards to uranium miners, virtually no attention has been focused upon possible reproductive effects that may result from exposure to radiation. Could these reports indicate such an additional arena of health effect either on miners or on others living in the vicinity of the mines and mills? The biologic and epidemiologic literature does not lend much support for adverse genetic outcome. The UNSCEAR report (UNSCEAR, 1977) summarizes much of the existing data. For example, on the basis of many animal studies and what has been observed in atom bomb survivers in Japan, it has been estimated that mutation rates resulting from low LET radiation to paternal germ cells would be 60 X 10-6 recessive and 20 X 10-6 dominant mutations per gamete per rad. There would be a five-fold increase in the number of recognizable abortions. The doubling dose for genetic disorders in mice is estimated at 100 rads. The assumption has been that low levels of exposure, such as might be received occupationally from uranium mines and mills or environmentally will produce reproductive effects that would defy distinction from background rates. However, the possibility can not be dismissed. In man, spermatogonia are thought to be three-fold more sensitive than in the mouse. Also, the high LET radiation from alpha particles is as much as 20-fold more effective in inducing changes in meiotic and post meiotic stages of cells, compared with low LET radiation. There is some degree of localization of alpha emitters in testicular tissue after inhalation of radon and radon daughters (Blanchard, R.L. and Moore, J.B., 1971; Pohl, E., 1964). The slopes of doseeffect curves are affected by type radiation and rate of administration. Data on such curves are poorly defined and debated as to whether there may be increased or decreased effect per unit dose at low levels of high LET radiation. Increased rates of aberrations of chromosomes in peripheral lymphocytes cultured from uranium miners have been reported (Brandom, W.F., et al., 1978). At cumulative exposures of 100 working level months (WLM) or less, a range of exposure lower than the limit of current occupational standards, the aberrations were increased more than two-fold. Our interest has led us to pursue the question of reproductive effects along three separate paths of inquiry: studies of the secondary sex ratio, cytogenetic study of human sperm, and studies of rates of congenital anomalies. I will present the thrust of our findings, most of which remain preliminary, comment on their interpretation and limitations, and indicate directions needed for future research. The secondary sex ratio is the ratio of males to females at birth. In the U.S., the ratio averages around 1.05. Ratios in blacks are somewhat lower (1.025) than in whites (1.053). For American Indians, the data are less definite. Values from Oklahoma and California are similar to whites (1.05). Southwestern tribes have, as we shall see, varying levels. The theoretical effects on sex ratio resulting from irradiation of the zygote are based on the principles of sex-linked genetics, including differential effects of lethal dominant and recessive mutations on the sex chromosomes, complicated by possible non-disjunctional events. Observations have done little to clarify, confirm or refute the theories. The sex ratio of progeny of survivers of the atomic bomb showed little change (Schull, W.J., Otake, M., and Neel, J.V., 1981). Observations in children of uranium miners having been inconsistent. Most frequently cited is a study of miners in Czechoslovakia (Müller, C., Razicka, L., and Bakstein, J., 1967). Compared with children born to miners prior to the start of mining, the sex ratios of children born after the start of mining were decreased -statistically significant after correcting for birth order. The ratios in first-born children were, before the start of mining, 1.118, and, after the start of mining, .713. In the interview survey at Shiprock, the sex ratio in families of non-miners was 1.03, and in families of miners it was 0.73 (p < .05). Dr. Alan Goodman at the University of New Mexico has studied trends in the sex ratio in the general population in New Mexico and Arizona with particular reference to counties in the Four Corners area and the Navajo Indian Reservation, areas where uranium mining has been active_ His findings (unpublished) are as follows: (1) Beginning in the early 1950&apos;s, there has been a modest, but persistant and statistically significant decline in the secondary sex ratio for the state of New Mexico compared with the U.S., a decline that roughly parallels the emergence of uranium mining in the Grants mineral belt in northwestern New Mexico. (2) Data available for the 11 years since 1969 show that among the five counties with ratios significantly lower than the state

Jan 1, 1981

By George B. Rice

In a recent speech in Pittsburgh, Dr. George Keyworth, the President&apos;s Science Advisor, made a statement which I believe deserves our very careful consideration. Dr. Keyworth said that there is no energy crisis. The crisis, he explained, is simply that people refuse to accept the solution. The solution which Dr. Keyworth has in mind is increased utilization of our abundant supplies of solid fuels and, in particular, uranium. I share his view concerning the solution to our energy needs. The use of uranium fuel is a safe, clean, and dependable means to generate our electric power. It is time that we addressed the real energy crisis: the refusal to accept the nuclear solution. The reason for the refusal is not difficult to find. It is nihilistic thinking about risk. Under this thinking, we assume the worst possible case and act accordingly, simply because we cannot prove to a total certainty that nuclear energy is perfectly safe. If this absolutist approach were generally applied throughout our society, there is no doubt all of us would soon be sitting around our campfires fearfully holding the wild animals at bay with our trusty spears. Today I am here to enlist your support in reversing the regulatory trend that threatens the very extistence of the nuclear power industry. As distinguished scientists, engineers and businessmen, you can use your influence to help bring rational regulation to the industry. Our industry supports strong safety and environmental protection programs. We understand the need for and do not object to reasonable regulation. Many anti-pollution measures can be practical to implement, cost effective and highly successful in minimizing environmental impacts. However, it is a fact of life that in the field of health and safety regulation, the law of diminishing returns operates with a vengeance. Absolute or near-absolute safety is impossible and any attempt to achieve it is intolerably costly. Fixation on absolute safety is particularly acute in the regulation of the nuclear power industry. Government Agencies, overly anxious to allay the irrational fears of those opposed to nuclear power, are literally regulating the industry to death - exactly the result sought by the anti-nuclear groups. Dr. Robert L. DuPont wrote in a recent issue of [Business Week]: "The nuclear power industry has been virtually stopped in the U.S. [because of fear]. This is true despite the fact that for more than 20 years the commercial nuclear industry has operated under unprecedented public health scrutiny and that to date there have been no radiation-related injuries, let alone deaths, suffered by any member of the public."1 I believe a useful way to convey the nature of the problem faced by the nuclear industry is to review an example of [unreasonable] regulation. While the example relates to our domestic industry, I am certain there are similar situations in other countries. For the example I will use the Nuclear Regulatory Commission&apos;s recently issued regulations governing the stabilization of uranium mill tailings.2 These regulations, known as the Uranium Mill Licensing Requirements, specify, among other things, that radon emanation from uranium mill tailings be limited to no more than 2 pCi/m2-sec. First, one must understand that this standard will have virtually no impact on the total amount of radon to which the public is exposed. Radon emitted from even completely unstabilized tailings piles is a tiny fraction--much less than 1%--of the amount of radon released from natural soils in the United States.3 In fact, it is far outweighed by natural variations in the background flux. For example, changes in the level of the Great Salt Lake in recent years have had [eight times] as much effect on the amount of radon released into the Salt Lake City regional air than the annual release from the Vitro Mill tailings pile located in that city.4 Nevertheless, NRC claims that the standard is required to protect the public. The Commission admits, however, that there are no studies which establish that exposure to radon at the low levels associated with uranium mill tailings will result in any adverse health effects.5 In the absence of actual evidence, the Commission assumes that some such effects will occur on the basis of the linear, non-threshold model.6 Employing this model, NRC calculates that the maximum hypothetical risk for the average member of the population is only about 1 in 70,000,000 from the radon that would be emitted from [three times] the number of mills now in existence, even if the tailings produced through the year 2000 are left unstabilized.7 NRC has elsewhere explained that this level of risk would be equivalent to the risk posed by "a few puffs on a cigarette, a few sips of wine, driving the family car about 6 blocks, flying about 2 miles, canoeing for 3 seconds, or being a man age 60 for 11 seconds." This level of risk is [de minimis] in comparison to other risks commonly and readily incurred in our society.9 Moreover, even this remote risk is overstated. A group of prominent health physicists, including experts from the Department of Energy, The Environmental Protection Agency, Britain, Canada and Germany recently published a study indicating that the risk to the public per unit exposure to radon can be no greater than one-third that suggested by the Commission, and [may in fact be zero].l0 Regulators routinely rationalize the need for their regulations. For example, NRC attempts to justify the radon flux standard because it is necessary to reduce the risk to someone who builds a house on top of a tailings pile. This possibility, however, is totally unrealistic because the Mill Tailings Act requires that stabilized tailings be transferred to

Jan 1, 1981

By D. B. Sikka, R. B. Bhappu

Porphyry-type copper-molybdenum (Cu-Mo) deposits typically occur in the Phanerozoic rocks and have been well-documented. During the past two decades, a number of porphyry-type Cu-Mo deposits that range in age from 1055 Ma to 2970 Ma have been identified in the Precambrian rocks of Australia, Canada, China, Finland, India. Namibia and Zambia. The Malanjkhand porphyry copper deposit M.P., India is estimated to contain 789 Mt (870 million st) averaging 0.83% copper (mill headgrade); 0.004% molybdenum; 0.2 g/t (0.006 oz/st) gold; 6 g/t (0.175 oz/st) silver and a cap of 7.5 Mt (8.2 million st) of oxide ore averaging 0.8% copper. The economic potential of the expanded copper mining milling, smelting and refining complex is expected to yield cathode copper 118.6 kt (130,700 st); molybdic oxide 830 t (914 st); gold 1.9 t (61,732 oz); silver 46.6 t (1.5 million oz); sulfuric acid 240 kt (264,500 st), copper from leach dumps 11.5 kt (12,600 st); nickel 24 t (26,400 st); cobalt 84 t (92,600 st); bismuth 16 t (17.6 st); selenium 48 t (53 st), tellurium 4.8 t (5.3 st).

Jan 1, 1995

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study was conducted to control iron in copper electrolyte streams using Eichrom Industries&apos; new monophosphonic/sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27-g/L iron and can be readily regenerated. In addition, the new resin can easily be synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydrometallurgical streams.

Jan 1, 2002

By Robert A. Bauer

Investigations of bedrock within subsided areas over abandoned coal mines reveal) very little disturbance of the bedrock. In areas that have surface subsidence of .3 to 1 m (1.0 to 3.25 ft), examination of cores from exploration drilling and investigations of the boreholes by means of closed circuit television have shown that fractures are spaced at least .9 to 3.6 m (3 to 12 ft) apart and are located within a zone 6 to 15 m (20 to 50 ft) above the collapsed area in coal mines 42.6 to 112.7 m (140 to 370 ft) deep. The dip of the fractures ranges from 25 to 60 degrees, cutting across nearly horizontal sedimentary bedding planes. Typical core recovery is 80 to 95 percent within the subsided areas and 100 percent outside the subsided areas.

Jan 1, 1984

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By Ron Derrick

SX operators have conducted extensive shut-downs and repairs over the years to mitigate solution leaks from failed stainless steel false floors and walls in rectangular mixersettler mix boxes. Hydrodynamic modeling using first principles and constitutive equations of fluid mechanics can inform an efficient structural redesign sufficient to eliminate the plate failures. Updated mix boxes have been performing without failure for over a decade. Given the extensive construction of the original Holmes and Narver mixer-settler design throughout the world that includes stainless steel lined rectangular primary and auxiliary mix boxes, SX operators may benefit from the approach, eliminating costly shutdowns, leaks to containment, and hazardous repairs.

Feb 1, 2024

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By Raymond L. Jones

With the inauguration of the open pit operation in Bagdad, plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until the spring of 1961. Like all neophytes, we started something about which, on a commercial scale, we knew next to nothing, either dump preparation or leach procedure, and as a consequence, we are still paying the piper. True, we had been through an extensive laboratory pilot program, but it soon became apparent that there was considerably more to increasing solution volumes than simple multiplication. Had we initially possessed our present acumen, the Cyprus Bagdad plant could be operated more efficiently and at a better profit. During the past several years, the art of dump leaching of copper has improved in many ways, primarily because of the application of scientific principles gleaned from general mining practice. Rigid pH control and the use of atomic absorption techniques for rapid," accurate assaying have probably played a leading role in this respect, although we cannot overlook the other sophisticated electronic controls lending improvement to acid addition and pumping, better piping materials, and lastly, the more efficient use of our pregnant liquors. Thin too, the years of experience have given us a greater understanding of dump behavior in general; and, we can, to a greater extent, measure, predict, and avoid some of the idiosyncrasies inherent in every dump. However, it is my firm belief that we will still be confronted with unexplainable dump behavior as long as we are involved in leaching. We have found our dump to be a wonderful money bank, but one that is capable of yielding a wildly fluctuating profit.

Jan 1, 1975

By Joseph E. Worthington

The announcement of a high-grade ore intercept near Wenatchee, Chelan County, WA, by Asamera Minerals in 1983 triggered widespread interest in this old gold mining district. The district has a long history of exploration and production and was actually one of the few underground gold mines that operated in the post World War I1 years in the US. Gold occurs in a north-trending structural zone in folded and faulted Eocene arkose intruded by andesite and dacite dikes having dates in the 42 to 50 m.y. range. Ore has been mined selectively from ladder veins perpendicular to the trend, from the south end of the trend near Squilchuck Creek. These veins narrow and silicification becomes pervasive northerly where wider zones were caved later in the operation. Recent discoveries at "B" reef at the north end are also in wide zones of silicified arkose. The gold lodes originally cropped out as prominent silicified and iron-stained ridges that were described in the early days as "reefs." The early discoveries were made in out- crop about a hundred years ago, and two claims, the Gold King and Macbeth lodes, covering the most prominent out- crops on the north side of Squilchuck Creek, were staked in 1885 and patented shortly thereafter. A five stamp mill was erected in 1894, but failed to liberate gold for amalgamation. The two patented claims were acquired in 1934 by J. Keegan, who carried out limited exploration and shipped small amounts of flux ore to Tacoma during the next few years. There was no substantial exploration or development of the claims, however, for several years after that time, and ownership of the claims eventually passed to a series of trusts administered by a bank in Seattle.

Jan 1, 1990

By Steven A. Elmquist

INTRODUCTION R&D activities are needed, at a minimum, for a company&apos;s competitive survival followed in importance by the growth and diversification of the company. For most industrial companies, however, R&D is the business area that has been the most difficult relative to confident long-range financial commitments and effective control and relative to its value as a long-term investment. Investors look not only at the current profitability of the company but increasingly at the plans, actions, and quality of the personnel in position to improve the market position and profitability of an organization. "The strongest predictor of investment value is the degree of innovation of the &apos;company.&apos; I believe this is true of both strategic planning and R&D activities." R&D is the lifeblood of a company&apos;s future. If this basic premise-R&D for survival and growth-is believed to be true, why is it necessary to "Sell R&D in your organization? My personal experience, in a number of organizations, is that R&D budget is perceived as a business element area that could be delayed or reduced to improve the bottom line during difficult business conditions. I believe the following quote speaks volumes about this subject-"There is only one thing I know for certain about research, and that is it costs money-lots of it." -Unnamed, Hard- headed Financial Executive. A business must make money and be profitable in order to maintain and create jobs, pay taxes, cover working capital and costs of goods sold, and most importantly, create value for its shareholders. The foremost element of selling R&D, therefore, is to consistently demonstrate the R&D group&apos;s contribution to the bottom line.

Jan 1, 2004

By Donald V. Fites

The evolution of open-pit mining has been rapid during the last two decades. The development of larger, more productive and efficient equipment has been one of the key factors in this open-pit advancement. Selection of the proper equipment and its correct usage is paramount to successful operation while maximizing return on investment. The quantity of material being moved prior to mining the saleable product is increasing at a significant rate. For example, at a southwestern copper mine more than two hundred million tons of over- burden have been removed prior to exposing an ore which contains less than 1% copper. A recent survey of twenty-three Western Hemisphere copper mines reveals the average strippingratio was 2.2:l with a range of 0.9-8.5:l. In the face of increased mineral demand, the resulting technological developments and rising overburden to ore ratios, many open-pit mines now use totally different concepts for the removal of ore and overburden. An increasing number of these concepts now being installed include wheel tractor scrapers as a major part of the material handling system for unconsolidated overburden removal. To say scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. As reported in the Minerals Year- book, however, about one-half of the material moved in metal and non-metal mines is never drilled and blasted or broken by other means. We will, therefore, in this paper, concentrate on the role of wheel tractor scrapers in unconsolidated overburden; the area of greatest usage.

Jan 1, 1969

By M. Argiantopoulou

In today?s mining environment, improving production, performance, productivity and profitability is crucial. Production, ancillary, plant and shipping equipment need to be monitored and controlled by online systems delivering production statistics and real-time information to everyone involved, including equipment operators. Traditional systems currently in use today, operate in an iterative mode constantly switching between scheduling and execution. However, the real world tends to change in ways that invalidate such advance schedules. Agent based computing has been hailed as the most significant breakthrough in software development and the new revolution in software. Agent systems are being used in an increasingly wide variety of applications, including complex mission critical systems such as Air Traffic Control. This paper presents the possible ways that multi-agent systems can be applied to mine production and rehabilitation scheduling problems with focus on real time fleet management, plant and equipment performance monitoring, downtime and delay reporting, stockpile management, personnel and equipment tracking and product distribution and transportation.

Jan 1, 2006

By J. B. Hiskey, V. M. Sanchez

Electrochemical oxidation of arsenopyrite (FeAsS) has been investigated as an attempt to gain a better understanding of its dissolution chemistry. Rest potential measurements, cyclic voltammetry and constant potential experiments were conducted in the pH range from 8 to 12 in the absence and the in the presence of cyanide. A two-step reaction sequence is suggested by the electrochemical measurements. The initial step is described by: [FeAsS+6H20=Fe(OH)3+H2AsO3- +S°+7H++6e] The second step involves the oxidation of the arsenite and sulfur according to the following reactions: [H2As03-+H20=HAsO24-+3H++2e and S° +4 H2O=SO4-+3H++6e] Stoichiometric determinations confirm that 14 electrons are involved in the overall reaction.

Jan 1, 1992

By L. Alan Weakly

At a time when the US mining industry is struggling to emerge from a lengthy recession, the burden of new, unnecessary regulations could shorten the life of, or be fatal to many domestic mining companies. The possibility of new restrictions on the use of diesel equipment operating in underground mines is one example of unnecessary regulations. These could cause serious harm to the economic health of many mining companies. Whether future health-related Mine Safety and Health Administration (MSHA) regulations restricting the use of diesel equipment are unnecessary, depends on whether these restrictions are supported by fact or created in a political environment. The mining industry has benefited from the use of diesel equipment in underground metal-non-metal and coal mines for more than 50 years. Since first introduce to underground mines in the early 1940s, the use of diesel equipment has grown in numbers and size. During this time, the mining industry in America has achieved much higher productivity rates and improved safety. Although all these gains cannot be attributed to the greater use of diesel equipment, a high percentage can be. I began my professional mining ca¬reer in 1970 working in the Missouri lead mines. At that time, the use of diesel equipment was well established in metal-non-metal mines throughout the United States and many parts of the world. As director of mining research for St. Joe Minerals Corp. (now The Doe Run Co.), I was involved in research to improve mining productivity and safety. This involved investigating the better and safer use of existing or new mining methods, products, equipment and people. Within this group, diesel equipment had the single largest positive impact.

Jan 1, 1993