Search Documents

By Jan Walaszczyk

The paper concerns the calculation of stresses and displacements in working area of room-and-pillar mining system of cooper ore mines. A three-dimensional rock mass model based on the finite element method has been developed. The complete strain-stress characteristic for pillars has been applied, but for the purpose of modeling the curve has been approximated by three segments of lines: - the first represents a behavior of pillar before a failure, -the second corresponds to a progressive pillar failure phase, - the third represents the part of the curve, where the increase of strains do not cause the stress changes, and it is called the residual strength. The criterion of model stability has been derived, which can be useful for predicting rockmass stability. The programs have been built, which allow to calculate stresses in bar elements, displacements in plate nodes, and estimate the stability of the model, which consists of plate elements and one-dimensional elements with a segment strain-stress characteristic. The programs were used to consider two different problems, which are connected with mining design and the exploitation systems.

Jan 1, 1992

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda's interest in the techniques stems from long experience with vat and heap leaching, 'dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971

By W. J. Adamson

Strategic Data Planning (SDP) is an emerging technique for the analysis and design of information systems. This paper describes the use of strategic data planning in the formulation of a complete integrated set of mining technical systems for the Koolan Island iron ore mine. Applications covered include hydrogeology, geology, mine planning, surveying, quality control, laboratory and mine production recording. Koolan Island is 13 kilometres long and 5.5 kilometres wide at its widest point. Its sole industry is an open pit iron ore mine of 3 million tonnes annual capacity, owned and operated by BHP Minerals. Some of the production is used by BHP Steel International, but most is exported. The orebody is steeply dipping and is mined bench by bench. Outturn grades for run-of-mine product are iron 66.5%, silica 3.0%, alumina 1.0%. Computer systems are run on Data General equipment, currently an MV10000. Computer applications, which are shared across mine sites, are developed and maintained by BHP Information Systems in BHP's Melbourne Office.

Jan 1, 1986

By John C. Draper

[Duquesne Light Company's three power plants in western Pennsylvania are now receiving high BTU clean coal from a new coal preparation plant. When burning coal from this plant, particulate emissions are greatly reduced and the sulfur content of stack ace descend. The cleaner coal also leads to more effecting overall operating of the power plants because of less bulk handling of fuel and ash. Environmental improvement is an important benefit of the cleaner, more complete combustion.]

Jan 1, 1976

By David A. Fawcett

An auxiliary cross-pit mining system, working in tandem with the prime excavator, is evaluated technically, operationally and economically for application in the selective removal and replacement of soils and unconsolidated ovezburden. Previous studies on cross-pit technology and applications of this technology are briefly reviewed. Stratigraphy plus pit, operating and economic parameters are assumed and applied in the evaluation and comparison of a base case dragline system with two alternatives - a dragline/scraper-dozer combination and a drag- line/cross-pit system combination. The economics of the proposed cross-pit system favour it as a viable alternative to conventional systems.

Jan 1, 1981

By F. L. Pirkle

The mineral zircon is mined for use as specialty foundry sands, abrasives, ores of ZrO2 and zirconium metal, refractories, and zirconium chemicals. It is produced as one of several products from heavy-mineral sand deposits associated with fossil shorelines. Because of its low coefficient of thermal expansion, its high melting point, its high refractive index, and its chemical inertness, it is an attractive refractory material. Zircon varies from deposit to deposit in terms of grain size, grain shape, and chemical impurity. Thus, there is a wide range of commercial products differing in impurity levels, particle shapes, and grain sizes.

Jan 1, 1992

By Steven M. Puricelli

In recent times, smelter off gases treatment plants have become more efficient and environmentally friendly. Where in the past it was acceptable to process only high strength, treatable furnace gases, new smelters must now treat primary gases and abate dust and SO2 from secondary gases: Processing smelter gases can present some interesting challenges. Some equipment can see varying concentrations of sulfuric acid, up to the boiling point, with a periodic table of contaminates thrown in for good measure. Treating weaker secondary gases have, in the past, been cost prohibitive. Nowadays, new technology, like physical absorption or catalytic carbon, show promise for economically treating low strength secondary gases. Modem smelters do a much better job of treating the SO2 laden gases generated by the smelting process but significant challenges remain.

Jan 1, 1998

By Peter L. Siems

Humid tropical environments pose many problems for mineral exploration. The problems result from thick lateritic soils, dense vegetation, seasonally heavy rains, deep chemical weathering, few outcrops and thick saprolites. Although geochemical exploration should be potentially a useful technique in these environments, it appears from the scarcity of reports in the literature that insufficient attention has been paid to developing procedures that are specific to the needs of humid tropical areas. For this reason, the authors believe that this account of a geochemical study in a tropical coastal area on the edge of the Brazilian shield is of general interest and importance for potential geochemical exploration surveys in similar areas within the tropics. The objective of the geochemical study was to develop a practical technique of reconnaissance geochemical prospecting for copper deposits in Brazilian tropical coastal lowland areas. In order to achieve this objective, information concerning the secondary dispersion of copper in these areas was required. Consequently, an orientation survey was designed to provide this information. The present account contains details of the geochemical study and the information about the secondary dispersion of copper that was acquired during the course of the orientation survey. Location and Climate The field area is on the Atlantic coastal lowland of Brazil at latitude 13°S. It lies approximately 10 kilometers south of Maragojipe, a city of 15,000 inhabitants; this city is on the western side of the Bay de Todos os Santos about 45 airline kilo¬meters northwest of Salvador. (See Fig. 1) A good gravel road from Sao Felipe to Sao Roque do Paraguay crosses the southern part of the field area. The climate of the area is hot and moist, and is without prolonged dry periods. The mean annual rainfall is about 1600 mm (63 in.) and the greatest precipitation occurs during the winter months of May and June and the summer months of December

Jan 1, 1972

By E. W. Greig

This paper is an account of exploration for bauxite in the Amazon Basin, Brazil, and particularly of the discovery, exploration and development by Alcan of the Trombetas deposit so a general account of the Trombetas Project has already been published in E/MJ (Anon. 1975) to which the reader is referred for details on owner-ship, infrastructure and construction as well as the proposal for mining and treating the bauxite. It is impossible to consider the Trombetas deposits in isolation. A regional account of bauxite in and around the Guyana Shield and the northern portion of the Brazilian Shield is included and it is suggested that these deposits all formed during Tertiary time under similar conditions.

Jan 1, 1977

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By K. P. Chong

Fracture toughness of oil shale is an essential property in fragmentation to optimize particle sizes and permeability distributions in in-situ processes. Fracture mechanics of oil shale has been based on conventional fracture mechanics using notched samples and assuming the material to be isotropic and elastic. Oil shale is a layered material more accurately characterized as transversely isotropic. The senior author proposes to use a semi- circular core specimen with a center crack subjected to three point bending. Singular crack tip elements with isoparametric elements are used. The precracked semi-circular disk is modeled under displacement loading. The effect of crack length on the non-dimensionalized stress intensity factor is investigated by strain energy method, ellipse method, and stress method. Very close agreements are found. The fracture toughness is obtained by compressing the specimen in to failure. Parameters such as oil yield are investigated.

Jan 1, 1984

By R. E. Musgrove

At the present time Climax Uranium Company recovers vanadium oxide from carnotite type uranium ores in the mill at Grand Junction, Colorado, The flowsheet of this mill is shown in Figure I. Vanadium is solubilized by a salt roast of the slime fraction of the ore and dissolution is accomplished by a water leach. The metal is precipitated from the pregnant liquor as sodium polyvanadate by heating to boiling and adjusting the pH to 3 with sulfuric acid. The sodium polyvanadate, commonly called, "red caken, is filtered, melted, and cast into thin flakes. This fused flaked vanadium oxide is the material which is packaged for sale. Fused vanadium oxide, marketed by Climax, contains approximately 87% V205, 7% alkali oxide, 0.08% sulfur, 0.03% phosphorus, and less than 0.5% Insoluble. This material is of a lower grade and has a higher alkali oxide content than other vanadium products offered for sale at this time. A typical analysis of a high grade vanadium oxide currently offered for sale by another company is 98% V205, 1 - 2% alkali oxide, less than 0.05% sulfur and less than 0.2% Insoluble. The only reagent consumed in the precipitation of the sodium polyvanadate is sulphuric acid. The total reagent cost is 0.58 cents per pound of vanadium oxide produced.

Jan 1, 1958

By G. Pan

The production data of many mines have not reconciled geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metals are sometimes as large as 30%. A number of factors are responsible for such unpleasant outcomes. A major cause, however, is the lack of geological controls in the implementation of geostatistical techniques. Geological modeling establishes geological constraints and mineralization/ore envelopes. Geological constraints are usually established through drill hole interpretation. Mineralization and ore envelopes have been delineated manually based on assay grades. The issues associated with manual methods are: •Time requirements . •Inconsistent dilution. •Uncontrollable implementation variance. Although the time issue may not be a big concern for some companies, the other two have been responsible for many undesired estimation errors. A new geostatistical approach described in this study is designed on the basis of indicator and ordinary kriging. The central component of the method is the procedure for automatic delineation of mineralization and ore envelopes. The method, referred to as probability assigned constrained kriging (PACK), is demonstrated on a Carlin-type gold deposit. The estimation results are compared to blast-hole based production panels, showing that the estimated tonnage is about 2.1 % higher than the actual production, and the average grade is about 2.4% lower.

Jan 1, 1995

By David A. Summers

Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these area has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generally have been short in length, although where methane drain- age operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the Federal Government, methods have also been developed for draining seams of coal of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes.

Jan 1, 1979

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

By J. C. Zelanko

The U. S. Bureau of Mines conducted a multi-faceted geomechanics research project at a bump-prone longwall coal mine in eastern Kentucky. This mine presented a unique opportunity to study coal mine bumps in that the problem appeared to be confined to areas beneath a sandstone channel of limited areal extent. The Bureau's research plan sought to exploit the uniqueness of the site by monitoring strata behavior and longwall support reactions as the longwall face approached and passed beneath a sandstone channel. The study incorporated static pillar stress and strata deformation measurements, shield support leg pressure measurements, and microseismic monitoring as well as geologic mapping and the collection of observational data. Data collection was underway when a major coal bump occurred on the longwall face at the mine. Pillar behavior (load and deformation), shield loading, and microseismic activity were monitored prior to, during, and after the bump. Observations in the tailgate indicated that these pillars were failing prior to and after the face bump. Shield load data which were evaluated in an effort to identify trends which could be used to forecast coal bumps appear to provide a measure of the effectiveness of destressing operations conducted on the face (e.g. shot firing). Analyses of microseismic data revealed anomalous values associated with microseismic "energy" prior to the face bump. In addition, microseismic source location data and underground observations provided some insight as to the sequence of pillar and face bumps.

Jan 1, 1991

By N. L. Parduhn

Populations of Bacillus cereus spores are elevated in soils over four subsurface gold deposits in the western United States. Large deposit-to-background ratios of B. cereus populations were obtained in soil traverses over the Minnesota vein deposit, Empire District, Colorado (maximum 50:1); the Shasta (maximum 3,500:1), and Evening Star maximum 18,000:1) vein deposits, Shasta County, California; and the Hog Ranch disseminated gold deposit (maximum 40,000:1) in Washoe County, Nevada. Small increases in the concentration of toxic metals in the soil may be responsible for the elevated spore populations. The observed elevation of B. cereus spore populations near these gold deposits indicates that the method should be further investigated as a potential exploration tool.

Jan 1, 2013

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, 150 km southwest of Ciudad Juarez. The ore deposit was discovered in 1979, and was placed in production in 1992. The production rate is about 2400 tpd from an ore reserve of 8.5M tonnes. Grades average about 8 % Zn, 0.5 % Pb, 0.2 % Cu and 50 g Ag per tonne. Substantial inflows of water into the under-ground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark was operated through a joint venture, Minera Bismark, S.A. de C.V., with U.S. and Mexican partners, but since early 1993, it is wholly Mexican-owned and operated.

Jan 1, 1994