Search Documents

By L. A. Clark

Although vein-, syenite-, and pegmatite-type deposits are known in Saskatchewan, recent intense exploration stems from discovery of several exceptionally high grade uranium and uranium-nickel deposits locallized near the basal unconformity of the 1.3-1.4 b.y. Athabasca Sandstone Formation. Graphitic basement rocks and post-Athabasca faulting or brecciation coincident with the unconformity are important in locallizing uranium deposits which form as tabular, shoe lace-like bodies with grades averaging over two percent and containing up to 50,000 tonnes U308. Some deposits have similar nickel contents. A few published sandstone analyses average 0.8 ppm uranium while basement granitoid and meta-sedimentary rocks vary from 0.5 to 20 ppm. In the proposed genetic model, traces of uranium are leached from these rocks by oxidized formation waters sweeping through the sandstone and along faults. Solutions are reduced and uranium is precipitated as basement graphitic meta-pelites are encountered along brecciated fault zones.

Jan 1, 1979

By M. K. McCarter

In 1963, a major expansion program at Kennecott's Bingham Canyon mine converted rail operation in the upper portion of the pit to truck haulage. Since that time truck-haulage capacity has increased to about 272 000 Mg (300,000 tons) per day. The majority of this production is waste material which is deposited in monolithic dumps located on the eastern slopes of the Oquirrh Mountains. The largest of these dumps, referred to as Copper Notch and Keystone, measures approximately 1830 m (6000 ft) in length, from 180 to 300 m (600 to 1000 ft) in height, and contains some 430 Tg (470 mil lion tons) of waste. The height, structure, rapid rate of growth, and anticipated leaching suggested the possibility of dump failure. In order to evaluate this possibility, an outside consulting firm was retained in 1966 to investigate the stability of the growing dumps. Their investigation indicated that, other than superficial movement, the waste dumps would be stable under static loading, and that soil distribution was not continuous enough to sustain massive foundation failure. Since this investigation, however, several failure processes have been observed. Crest settlement occurs frequently in response to compaction and over-steepening in the upper portion of the dump surface. Over-steepening results from accumulation of fines near the crest caused by natural segregation. Normally, coarse material, near the base of the dump, exhibits an angle of repose near 0.65 rad (37"). The fine material, however, stands as steep as 0.75 rad (40"). Periodic equilibrium adjustments cause stepwise settlement (Figure 1) of the dump surface and occasional sloughing of the protective berm. Routine surface preparation by dozers and graders and frequent inspections by supervisory personnel have proven adequate in preventing problems associated with this form of crest instability.

Jan 1, 1976

By J. B. Moritz

From the beginning, man has concerned himself with the task of controlling the elements and forces about him so as to provide a better and easier life. In the accomplishment of this task, he is required to utilize in the best way possible the resources which are available to him. In many cases, the available resources must bee refined before they are in a useable form. Many products in the mining industry fall into this category, as some form of refinement is generally needed to produce a saleable product. Over the years man developed more efficient ways of extracting the resources from earth through the use of electrical and mechanical devices. A reduction in manual labor, which is a by-product of increased efficiency through machines, has also been enjoyed. The combination of man's senses and new devices has also enabled man to reach a high level of control in the refinement process. Control of a process through machinery and man's senses has been termed an "art." Until recently man's senses (sight, feel) were the only method available for making measurements simply because suitable measurement devices (instruments) were not available. Even today some items cannot be measured and man's senses must be used. However, the development in our instrument laboratories tends to indicate that time will eliminate this. In recent years, control of many processes has been reduced to a science and part or all of the art eliminated. This does not imply that process art should be degraded; however, when a process is reduced to a science, uniformity of the product from day to day is attained. Decreased processing time and more efficient use of additives and raw materials are other benefits that result from control of a process when it is reduced to a science.

Jan 1, 1965

By James M. Baylor

Ladies and geltlemen, it is indeed a privilege and a pleasure to be here in Denver with you. I want you to know too I'm not a stranger out here. Golden, Colorado is the headquarters of A. T. Massey Coal Company's Western Division, headed by Vice President, Gregory H. Hoyl. I also have a very close friend and fraternity brother who works and lives in Denver so I could talk on and on about this area and our western coal properties, but it's Massey's coal terminal business I'm to focus in on today, and that's a horse of a different color. So on to the subject of my address: MASSEY COAL TERMINAL INVOLVEMENT As I have stated on other occasions, A. T. Massey Coal Company, for better or for worse, is in the coal terminal business.

Jan 1, 1981

By Sylvain J. Pirson

A fluid mining process has been developed by the writer whereby phosphate deposits are leached in place through the injection of a weak and recoverable acid solution much in the same manner as in the recovery of oil by water-flooding. The phosphate mineralization is dissolved In place, selectively treated in a surface plant and a high grade diacalcium phosphate substatially free of fluorine (hence of feed grade quality) is recovered. Because of its finely divided and powdery state, the plant product is highly desirable as stock material for the manufacture of triple-superphosphate and of high grade phosphatic chemicals. Details of well completion, fluid injection, areal sweep and solution efficiency, plant design and economics are presented The rate of return on investment is particularly attractive under conditions of shallow occurrence of the phosphate mineralization such as in the Bone Valley formation of Florida. The process may also be applied economically to the Phosphoria formation of wide- spread occurrence in the Northwest United States through the application of selective formation fracturing (or Hydrofrac) previous to fluid mining operations.

Jan 1, 1959

By Walter C. Labys

This paper reports on recent modeling efforts to analyze the eastern U.S. steam coal market with a cross-sectional econometric as well as a quadratic programming approach. The background to coal modeling is examined first. The particular aspect of the steam coal market to be modeled are then presented and the corresponding coal model described. Both empirical results and rigorous mathematic pertubation analysis are presented. Conclusions are then drawn regarding potential modeling applications in the policy area.

Jan 1, 1979

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By W. Clark Ashby

Trees are an essential ingredient of sound reclamation in nearly all surface mining regions. There are, however, possible problems in current reclamation regulations and practices which need to be evaluated and remedied. Recognition and accomodation of growth requirements for trees and other plants will greatly increase reclamation success. Surface mining encompasses a series of processes from a pre-mining baseline study to bond release following revegetation. Land owners, and society, have a great interest in subsequent plant growth on reclaimed areas and in future land values.

Jan 1, 1981

By James A. Doolittle

In the underground type of mining operation, the finer portion of the waste material commonly is pumped as a hydraulic slurry to a tailings disposal pond. (1)* The tailings slurry is deposited via a pipe manifold system located around the perimeter of the pond. This method of deposition produces zoning because the coarser material tends to settle out immediately while the finer particles tend to remain in suspension and are deposited progressively nearer the center of the pond. The manifold system must be raised periodically as the pond fills with the tailings material. Over a period of time, this procedure will produce a zoned embankment known as a tailings dam. A typical pond and dam are shown in Figure 1. In plan view, the dimensions of tailings dams can be on the order of miles, with the height of the dam reaching 100 to 200 feet. Due to such factors as inadequate compaction, inherently low strength of the tailings material, and the possibility of high phreatic surface, many dams at some point become unstable, i.e., the factor of safety against a slope failure approaches 1.0. Remedial measures are required to improve the safety factor in order to prevent massive failure of the dam. In most cases, stability can be improved by effectively flattening the slope of the dam as shown in Figure 2, but this is not possible in every case. Occasionally, a tailings dam is constructed adjacent to a natural or legal boundary so that it is not possible to construct a conventional berm or to reduce the slope angle with earth moving equipment. Even a terracing process would require removal of the material and this may not be practical. In such a situation, an alternate scheme to improve stability must be found.

Jan 1, 1974

By H. G. Linge

The Australian gold industry currently contributes some $4bpa to the national economy [l]. Some 40% of the total gold is produced in the region centred on Kalgoorlie known as the Eastern Goldfields of Western Australia. This region is the largest single centre of production with an output of some 100 tpa of gold [2]. In the Eastern Goldfields, refractory arseno­pyritic gold ore is an increasingly significant source of gold, feeding several operations utilizing bio-oxidation as the pre­carbon in pulp/leach (CIP/L) treatment process [1]. This paper desribes an alternative pre-CIP/L treatment option for use in the Eastern Goldfields based on the chlorination of arsenopyrite by chlor-alkali technology [3] using the salt resources available from saline water present in abundance in the region.

Jan 1, 1995

By R. K. Clifford

The formation of elemental sulfur on the surface of sphalerite in aqueous systems was investigated. Hallimond tube flotation tests showed that unoxidized sphalerite did not float well without a collector. Flotation recoveries of greater than 95 percent were obtained without the use of a collector or frother after the sphalerite had been reacted with oxygen under pressure and water at pH 2.8 at room temperature. High flotation recoveries also resulted when sphalerite was reacted in acidic solutions in the presence of platinum sponge, titanium sponge, 316 stainless steel, copper turnings, or [10-5M++]. Conditions which produced high flotation recoveries of sphalerite yielded contact angles of 37° to 40° and also produced elemental sulfur. The increase in elemental sulfur on the surface of sphalerite was detected by elemental sulfur extraction with petroleum ether, electron spectroscopy for chemical analysis (ESCA), and the electron beam microprobe. The quantity of elemental sulfur formed was insufficient to be detected by infrared or Raman spectroscopy, or by the optical microscope or by the scanning electron microscope. An electrochemical type reaction for the production of elemental sulfur in acidic solutions was proposed. The cathodic reduction of oxygen was the slow step which needed to be catalyzed. A chemical type reaction which produced H2S rather than elemental sulfur was evident in non-oxidizing conditions.

Jan 1, 1974

By Sarkis G. Ampian

This late 1979 Bureau of Mines report presents current stocks and monthly consumption rates for Guyanese refractory bauxite (GRB), with emphasis on the impact of the GRB shortage on the refractory and downstream industries, general background material, and an evaluation of the situation resulting from the strike of Guyanese bauxite workers during the summer of 1979. A study by the Bureau indicated that industry stocks contained little more than a month's supply of GRB--30,000 calcined short tons (CST), at present consumption rates of 25,000 CST per month. The report was requested by the Federal Emergency Management Agency (FW) in response to refractory industry requests that the Government release GRB from the National Stockpile to minimize forecasted industry problems. The report traces the historical innovations in the high-alumina and/or bauxite-type refractory products industry, eventually leading up to fabrication of modern, high-quality firebrick and monolithic refractories.

Jan 1, 1980

By Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980's. Approximately 50 million tons of hazardous wastes are produced yearly. One of the major aspects of the problem is the siting, design and construction of environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sires for several reasons: 1. Surface mines represent an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic savings when compared with sites on undisturbed lands chat might require extensive excavation or embankment construction.

Jan 1, 1981

By Randall C. Divito, Craig R. Eckdahl, Bruce D. Wagener, Joseph Klejwa

The existing Central City Tunnel was built primarily in the 1930s with a small portion as old as the 1880s. It conveys stormwater in downtown Minneapolis. It is a 4,400-ft long tunnel located 80 feet underground. The Central City Tunnel has experienced surcharging and surface overflows during heavy rainfall events. This paper presents the details of tunnel and shaft design for the new Central City Parallel Tunnel to mitigate the overflows. The design considered hydraulics and geotechnical engineering for the structural geologic conditions including the weak Saint Peter Sandstone and overlying strong Platteville Limestone. Ground conditions resulted in tunnel designs including large flat-back box tunnels and unique cathedral-shaped tunnel sections.

Jun 13, 2023

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By Dale D. Teeters

Today, I would like to talk about ways to maximize the efficiency of surface coal operations. I doubt I will present any startling new ideas, but my comments may, hopefully, stimulate some conversation today and later back at your own operations. Strip mining is a very old technique used by ancient societies. Only with the coming of the machine age in the early twentieth century did we attempt to increase the magnitude of our operations. The industry, as we know it today, really only got started in the early 1900s with the advent of steam shovels. In the first portion of this presentation, I will attempt to show that we have, in many cases, not changed the basics of strip mining, only the scale. In doing so, quite often we have complicated the operations to the point of being unmanageable and unprofitable.

Jan 1, 1981

By R. W. Smith

The electrokinetic and flotation behavior of the green alga Chlorella vulgaris was studied in the absence and presence of Pb(II), Al (III) and flotation collectors. It was found that the presence of Al (III) is necessary for good flotation of the organism whether or not Pb(II) is present when dodecylammonium chloride or sodium dodecylsulfate is used as collector. Best flotation using dodecylamine is at about pH 8 and best flotation when using sodium dodecylsulfate is at about pH 4. It appears because of the small size of the organisms that the Al (III) is necessary for flocculation to enhance bubble-cell contact and C. vulgaris removal from water. When N-dodecyl-2-aminoproprionic acid is used as collector good flotation occurs at about pH 4 without the addition of Al (III).

Jan 1, 1990

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025