Search Documents

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By Carlos Viramontes Aldana

Mining in Mexico is one of its post traditional activities, whose influence in the development of important cities and communications has been decisive. Precious metals and, to some extent, copper and tin were known and used before the Colonial period, but from the sixteenth century to tie end of the nineteenth century, mining and metallurgical industries were concentrated in the precious metals, mainly silver. This silver was exported to Spain and other countries under the Spanish. Rule, Mexican peso was known world wide since the end of the sixteenth century and Mexico ranked as the first silver producer since the eighteenth century.

Jan 1, 1985

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By Ronald M. Hays

The White Pine Copper Division of Copper Range Company is a large copper producer operating an underground mine, mill, and smelter on Michigan's Upper Peninsula. Principal water discharges are from the tailings basin where these discharges are high in dissolved solids because of mine water pumped into the basin. Principal air emissions are from the smelter where SO2 emissions are uncontrolled. Although water discharges and air emissions have not had significant environmental impacts, environmental regulations could require additional control procedures. Because of low copper prices and poor profitability, cost of compliance with possible new environmental regulations could have serious impact on White Pine with no apparent significant beneficial environmental impacts.

Jan 1, 1979

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By John D. Elmes

The purpose of this paper is to describe the geology and the modelling work carried out to date. The Lisheen Zinc-Lead deposit was discovered in April, 1990. The deposit comprises two stratiform sulphide orebodies, hosted within the Lower Carboniferous Waulsortian limestone formation. The fully diluted geological resource is 22.5 Mt @ 13.02% Zn and 2.19% Pb, based on a total of 548 diamond drill-boles and 10,998 sampled core intersections. Due to the absence of a geological marker it was necessary to apply economic criteria to define and model the resource envelope. In common with other drill-hole geological databases, the establishment of a workable geological model presents unique challenges.

Jan 1, 1998

By George J. Saulnier

The U.S. Geological Survey has developed mathematical-modeling techniques to assess potential impacts on the hydrologic system resulting from mining of coal and oil shale in northwestern Colorado. Potential impacts of oil-shale mining on ground-water hydrology have been simulated using a quasi-three- dimensional finite-difference model. The model has been used to simulate hypothetical mine-dewatering operations at two proposed oil-shale mines. Dissolved-solids distribution and solute transport were simulated with a three- dimensional finite-difference model that was used to evaluate the effects of flooding in hypothetical abandoned mines. The potential impacts of coal and oil-shale mining on watersheds were investigated using a digital watershed model. This deterministic physical- process model predicts responses of the hydrologic system to modifications resulting from mining in basins having snow as the major source of runoff and recharge. Potential impacts of coal development on surface-water quality were investigated using a river-quality assessment model.

Jan 1, 1979

By P. F. Ziemkiewicz

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalized according to construction cost, projected service life and tons of acid load treated. Results were dimensioned as $/tons of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

By M. L. Free, N. Dhawan, M. S. Safarzadeh, J. D. Miller, M. S. Moats

"The drum agglomeration of nickel laterite and gold ores has been optimized through the design of experiments (DOE) using a Taguchi L16 (45) orthogonal array to determine the optimum conditions for maximizing average agglomerate size and minimizing the amount of fines. The effects of controllable operating factors including moisture content (nickel laterite ore: 34-37%; gold ore: 7-10%), retention time (2-3.5 min), drum speed (15-45% critical speed), drum load (nickel laterite ore: 8-32 %; gold ore: 6-22%) and acid concentration (150-600 g/L) on the performance of the agglomeration process were studied.For nickel laterite ore, maximum average agglomerate size and minimum percent fines (-1 mm) occurred under the following conditions: drum load (23.7%), moisture (36.5%), time (3 min), drum speed (30% critical speed) and acid concentration (150 g/L). Under the studied nickel laterite ore conditions, the most effective parameters for maximizing average agglomerate size and minimizing the amount of fines were found to be drum load and acid concentration, respectively. Drum speed had a statistically significant effect on minimizing the amount of fines. Maximum average agglomerate size and minimum percent fines (-1 mm) for gold ore occurred under the following conditions: drum load (19.3%), moisture (8.5%), time (2 min 15 s) and drum speed (40% critical). The most significant factors for maximizing average agglomerate size and minimizing the amount of fines for gold ore were found to be drum load, time and moisture.IntroductionSeveral heap leach operations have experienced problems in terms of poor recovery due to percolation issues caused by low-grade complex ores, tailings and clayey deposits. Poor percolation can lead to low metal extraction due to solution channeling or the development of impermeable/dead zones within the heap (Dhawan et al., 2012; Kappes, 2005). Improper heap building practices such as the use of loose agglomerates and inadequate attention toward the presence of clay minerals have been among the main reasons for percolation issues. During the transport of ore material, severe segregation of the material can occur. To overcome percolation problems, a major improvement was made through the introduction of agglomeration prior to ore placement. If the ore particles and agglomerates are of similar size, segregation can be avoided to a great extent (Dhawan et al., 2013; Kinard and Schweizer, 1987; McClelland and van Zyl, 1988). Agglomeration improves the uniform percolation of solution through ore heaps and is applicable to many ores, wastes and milled tailings (Bouffard, 2005; Dhawan et al., 2013). Manning and Kappes (2005) reported agglomeration/ stacking accounts for ~14% of the total heap leaching operating cost. The cost of binder is a primary contributor toward the total cost. Also, the lack of consistent quality control tests for agglomerate often leads to operational problems. The details are mentioned elsewhere (Dhawan et al., 2013). Considering the significant contribution of the agglomeration/stacking step toward the total heap leach operating cost, it is appropriate to study the agglomeration behavior and its optimization for two different ores. The reason to study the same parameters for different ores is the fact that significant variability in the agglomeration behavior of different ores has been reported to exist in industrial operations."

Jan 1, 2015

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By R. Perez

The consumption of grinding media forms a significant part of the operating cost of a mineral processing plant. An estimated half billion pounds of steel in the USA and over one billion pounds in the world are consumed each year in wet grinding alone. However, there is some conjecture as to the interacting roles of abrasion and corrosion. In order to provide a more complete picture of the conjoint action of abrasion and corrosion, marked ball tests were conducted on different grinding ball compositions in a laboratory ball mill and the metal losses were measured on varying the conditions, i.e., pH, PO2, in wet grinding a Cu-Ni gabbroic rock and compared with taconite grinding. Ball wear rates ere discussed with respect to ball composition and microstructure and the varying conditions used in the grinding tests.

Jan 1, 1984

By R. Keith Evans

Potential large scale uses in secondary battery systems and fusion reactors together with a steady increase in demand for conventional applications, particularly in aluminum smelting, has resulted in an increasing interest in lithium and its compounds. Current world requirements are met from both granitic pegmatites and non-pegmatitic sources and although the emphasis in this short paper is on the pegmatitic minerals, and, in particular, on their "direct usage" applications, a short summary of other sources and requirements for chemical production is included for the sake of completeness.

Jan 1, 1977

By Manuel Gomez

This, report presents correlative data on ash and sulfur forms for Pittsburgh seam coal from Greene County, Pa. Prediction equations were developed for sulfur form distributions and washability characteristics. The equations developed were evaluated with an independent set of exploration core samples. It was demonstrated-that both sulfur distributions and washability characteristic's can be predicted from exploration core data ahead of mining. This information can improve the efficiency of selective mining techniques for the production of a uniform metallurgical coal product.

Jan 1, 1967

By V. I. Lakshmanan

Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market. Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogenous grinding. In addition to producing marketable coarse graphite by such autogenous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies.

Jan 1, 1984

By W. C. Yates

Lack of visibility from cabs of the large haulage trucks used in open-pit mines has become a serious safety problem. This Anaconda research program was conducted to develop a low-cost system for alerting haulage truck operators of the presence of small vehicles in their blind areas. Several systems, developed and tested to help solve this problem, are summarized and evaluated in this paper. As the size of the haulage trucks used in large open-pit mines has increased, so have the blind areas. Mine utility vehicles, pickup tucks and cars become concealed within these blind areas and, thus, become a serious safety hazard. Figure 1 shows the typical blind areas of a 150-ton haulage truck. The areas of greatest concern are those at the rear center and front right corner of the truck. It is within these areas of "no visibility" that numerous small vehicles over the years have been crushed by the large haulage trucks at various mine sites. Although the occupants in most instances, have escaped the vehicle before it was destroyed, injuries and deaths have occurred. The accidents, in most cases, were attributed to negligence or carelessness on the part of the driver of the smaller vehicle, but the problem of limited visibility still exists, and a solution is needed.

Jan 1, 1982

By M. Fig, J. Brune, C. Strebinger, G. Bogin, J. Grubb

"Although it is known that explosive gas zones can form and sustain combustion in a longwall coal mine gob, a complete account of the interaction of the methane flame and gob remains obscure. The goal of this study is to examine the impact of several gob parameters such as packing orientation and void spacing. The impact of ignition location is also detailed. A series of experiments with methane flames were performed in a horizontal cylindrical quartz reactor. The reactor was tested both empty and packed with an obstacle wall consisting of spherical glass beads to investigate the impact of various gob parameters. Results demonstrate that methane burning velocity is sensitive to all parameters investigated, and most sensitive to packing density and ignition location. INTRODUCTION The explosion at the Upper Big Branch Mine in 2010 and several other underground longwall coal mine fires and explosions show that explosive gases can mix with fresh ventilation air creating explosive gas zones (EGZs). Investigative reports of these fires have found that EGZs are able to move from the gob and into the active longwall face, endangering workers and equipment [1]. Currently, researchers at the Colorado School of Mines are using computation fluid dynamics (CFD) modeling to predict the location and movement of EGZs in the gob and along the longwall face [2,3]. It is the goal of this work to validate combustion models [4] that include interactions of the flame and the gob for future incorporation into ongoing CFD modeling of EGZs [2,3]. Throughout the years, there has been significant research investigating how flames interact with obstacles and propagate through porous media [4,5,7-11]. Since there is limited access to the gob in a longwall coal mine (Figure 1), the orientation and size of rocks and void spaces within the gob is unknown. Experiments of a simulated gob have been performed in a large scale flame tube in order to investigate the effect of scale (Figure 2) [4,5]. However, the variation in rock spacing, rock orientation, and void location makes it difficult to determine the impact of each of these parameters on methane flame dynamics. This study aims at gaining a stronger fundamental understanding of gob parameters such as spacing, orientation, and ignition location on methane flame propagation. The results from this study will provide a basis for experimentation in larger explosion vessels and will be used to validate methane combustion models for incorporation into longwall ventilation models of EGZ movement [2,3,4]. BACKGROUND Researchers have been studying flame propagation across obstacles and porous media for many years using various fuels and experimental setups [4,5,7-11]. Experiments have been performed in horizontal chambers with both ends open [7], horizontal chambers that are semi-open [4,11], horizontal chambers with both ends closed [8], and vertical arrangements [9,10]. Due to the variation in experimental setups and methods of characterizing flame dynamics such as flame speed, peak overpressure, or burning velocity it becomes difficult to directly compare results. Flame speed is a property of the mixture and refers to the speed of the unstretched flame front normal to the direction of propagation. This study characterizes the flame by its burning velocity, which is the difference between the flame speed and the speed of the unburned gases just ahead of the flame front. However, some references use the terms flame speed and burning velocity interchangeably. In this study, a semi-open quartz cylindrical reactor was used to determine methane burning velocity, which was used as a basis for comparison to determine the impact of obstacle configuration on methane flame dynamics. The quartz reactor also has the unique ability to allow for flame visualization. These features allow for faster combustion model validation [4]."

Jan 1, 2017

By T. V. Shockley

The Gulf Coast, from New Orleans, Louisiana to Brownsville, Texas, is one of the largest high energy consuming areas in the United States. This region has areas of very high industrial density. The lower Mississippi River from Baton Rouge past New Orleans has a high industrial density. Lake Charles, Louisiana, the Orange-Beaumont-Port Arthur area, Houston (4 separate areas) and Corpus Christi all have the same high industrial density. This situation developed due to good transportation, good labor conditions, good weather and the abundance of cheap energy-gas and electricity. Obviously the latter had the greatest impact. The availability of cheap natural gas made Gulf Coast sites very attractive to energy intensive industry such as metals and petro-chemicals. The area was also very attractive to refinery development due to the large supply (endless?) of crude oil available. As we all know, the energy situation has changed dramatically in the last five years. The cost of a MMBTU has risen from the 17¢ to 19¢ level to a price of $1.95 to $2.10. The price of interstate gas, as defined by the National Energy Plan recently passed by Congress, was approximately $1.98/MMBTU escalated to October, 1978. It goes without saying, that this has had a major impact on doing business in the Gulf Coast. As fuel prices soared, different companies responded in different ways; but overall, industrial energy consumption along the coast was reduced 20% to 25% from 1974 to 1975. Since 1975 production and energy use has been increasing, however, production at some plants is still significantly below plant capacity.

Jan 1, 1979

By L. T. Larson

Had the blank on the Abstract form been sufficiently spacious a more appropriate title for this paper would be: Neogene Tectonism, Magmatic Activity and Hydrothermal Precious Metal Mineralization in Anatolian Turkey; an Analog with the Basin and Range Province of the Western U.S.? Like the alternative title no thing in Turkey is simple. Its history is long and convolute; its culture fascinating; its metallogeny diverse and its geology very complex. This paper will focus only on the geology of western' Anatolia and the precious metal potential of this third of Turkey. The argument is in the article but to save the reader time and suspense I'll put my conclusions up front- the potential is great and the possibilities exciting.

Jan 1, 1989

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011