Search Documents

By O. Olajide, E. H. Cho

A laboratory study of the jigging process with Pittsburgh seam coal has been conducted. The laboratory-scale Baum jig used in this study was a McNally-Norton LO30X Right Hand Model Baum jig with an effective screen area of 0.186 m2 Feed material was prepared by selecting a size range from 6 mesh to 1.91 cm. Solid feed rates were 27.2 kg/min and 32.7 kg/min. Water flow rates were varied from 37.9 to 94.6 L/min. It has been found that smaller particles give higher values of density of separation and lower efficiency of separation. Increasing water flow rate increases the discharge rate of clean coal at a constant solid feed rate. It appears that the efficiency of separation increases by increasing water flow rate up to a certain value, and then levels off upon increasing the flow rate further.

Jan 1, 1988

By G. G. O. O. Uwadiale

Because mineral matter is finely distributed within the matrix, Nigerian Labia coal is nonresponsive to conventional processing techniques. However, testing has shown that Lafia coal can be upgraded by selective oil agglormation. The optimum oil concentration was found to be 10 mL of paraffin per 25 g of coal. A product containing 6% ash and 1.9% sulfur was obtained with a yield of 90%. Optimum results were achieved with a grinding; time of from 2.5 and 3 hrs, which produced a 98% -400 mesh product. However, further grinding wars found to be deleterious to the process. Also, high pH adversely affected concentrate yields. Utilizing kerosene as a bridging liquid, a product containing 4% ash and 0.33% sulfur was achieved at a natural pH of 6.3 with a yield of 85%. At pH 9 and 10, a product containing 4.5% ash was achieved with a yield of >90%.

Jan 1, 1997

By James G. Mock

The choice of equipment to be applied to a given installation by the Application Engineer begins with the data as presented to him by the user. This point in the relationship establishes a communication link, which will decide whether or not the correct piece of Overhead Equipment is applied at the most economic advantage to the user. The role played by the user cannot be minimized. No one knows better than he, just what work he expects to accomplish with this piece of machinery. However, all too often, he oversimplifies the requirements, and along with minimal crane and building parameters, merely refers to one of the following crane classifications as defined by The Crane Manufacturing Association of America, as shown in Figures 1, 2, 3, 4, 5, 6 and 7. This approach places the ultimate user in an unfair position, since he has then assumed the status of the machinery designer and must, therefore, assume the responsibility of the success or failure of the operation of that piece of machinery. If the user selects a Class "C" crane for his job requirement, when actually a Class "B" crane can adequately handle the work load, he is not offering the most economic solution to his company and added little to the cranes service capabilities.

Jan 1, 1973

By Richard J. Lewandowski

Corrosion and product contamination have been difficult problems for extractive metallurgy industries in the U.S. because of the highly active chemicals used. During the past twelve years, other industries, particularly the chemical and paper segments, began to combat this problem with some degree of success using newer materials of construction, including reinforced plastics. These materials are made by combining a corrosion resistant thermosetting resin with a glass fiber reinforcing material and are used to con¬struct hoods, stacks, blowers, tanks, towers, pipe, and equipment of the most complex configurations. For service in contact with aggressive chemicals, the equipment is most often fabricated with the bisphenol-A fumarate polyester resins because of their resistance to corrosive attack. Data from both laboratory work and case histories of field applications are presented-for many common chemicals found in extractive processes. Information is also presented concerning design standards and recommended construction procedures

Jan 1, 1970

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

In some 35 years in the explosive and construction industries, we have probably seen the extremes in drilling and blasting practices. All of you know that it is difficult if not impossible, to separate those two operations, particularly when we are searching for an optimum. Early in my career while doing engineering survey work for a major cross country pipeline construction company, we witnessed some of the wildest blasts imaginable, and they were wild for two reasons. Both the drill hole diameter and the drill pattern were such that when loaded with explosives, the factor in terms of pounds/cu. yd. was extremely high. On the other hand, in 1982 we were in an underground coal mine where just one hole was used to prepare a 20-ft. (6m) wide face. In this coal mine, they brought down 7 yd3 (5.35m3) of coal with just 1 lb. (.454 kg) of explosive. On a pipeline job, the factor may only be .1 yd3 per lb. of explosives. Open pit operations in the same geographical area may have almost the same type of rock, but similarities could end there. The several operators over the years will have installed different size-crushing equipment or variances will exist in other facets such as drilling, excavating, and haulage units. That tells us that if we have 6 operations in that common area, we are faced with a fact that there is an optimum drilling and blasting pattern for each of those six. We start at that point. We will note from Figure No. 2 the simple equations for determining either cu. yds. or tons. For a rock heavier than limestone, it may require only 10 to 11 cu. ft. (.31m3) for 1 ton (.91 metric ton) of rock in place.

Jan 1, 1986

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By Tetsuji Hirato, A. J. Monhemius, Yasuhiro Awakura, G. W. Warren, E. Peters

An electrostatic pseudo-liquid membrane technique, in which extraction and stripping take place simultaneously in a single reaction vessel using an electrostatic dispersion, was applied to recover Ni(II) from aqueous 0.1 kg m-3 Ni(II)(as NiSO4) – CH3COONa solutions, and the Ni(II) ions were concentrated by a factor of 9 into an aqueous 1.0 kmol m-3 HCI solution using D2EHPA as an extractant at the applied voltage of 3.7 kV for the dispersion. When the process of ESPLIM proceeds favorably, the concentration of Ni(II) in the upper part of the organic phase of the reaction vessel is lower than that in the lower part. In addition, the concentration of Ni(II) in the organic phase of the extraction chamber is higher than that in the stripping chamber. For the stable operation of this process, the stripping rate must be greater than the extraction rate to prevent the excess accumulation of Ni(II) in the organic phase which leads to the poor dispersion of the aqueous phase.

Jan 1, 1993

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By P. Holman

I would like to start this paper by looking back about twenty years to see where we have been in the mining industry. We will also look forward a bit and talk about what lies ahead. Here is what has happened to the world economy since the 1970s. Economic growth was strong in the early 70s, but slipped into a recession in the middle of the decade. Then, after a fairly decent recovery recession struck again in the early 80s and since then growth has been rather sporadic. All in all, it has been a real roller coaster ride. There will continue to be plenty of ups and downs in the world economy in the future.

Jan 1, 1993

By A. Delgado-Jiménez, O. J. Restrepo-Baena, G. Aristazabal

"Mining industry as a source of raw material is essential to society however, it lacks of good reputation due to the type of management historically applied to many of its social and environmental impacts. It is argued that this situation has hampered the obtaining of social license to operate of a lot of mining projects around the world. The last considerations are very common in Latin American countries. As a result, the mining sector has understood that the viability of the business long term is associated with more profit for the shareholders but also with activities that improve the livelihoods of local communities, enhance the capabilities of local governments and preserve the ecosystems around the projects. Nevertheless, recent studios have shown that most of the current advances to incorporate sustainability concepts in mining have been mainly focused on control and the prevention of environmental and social impacts of extractive activities. Thus, contributing to the development of territories around mining projects constitutes a fundamental aspect of the business competitiveness through reducing cost and risks of stopping projects, innovating new ways of relationship with stakeholders, improving the level of reputation of the industry as well as its position in the market. However, this contribution requires formal strategies and models that enable companies understand the different resources in the territories where their mining activities are developed and those resource transformations, in order to establish the best way to articulate the project with the territory, pursuing an effective contribution to its development, truly sustainable over time even after the mine closure. CONTEXT Currently in the world but especially in developing countries such as Latin Americans, different stakeholders are increasingly vigilant of how mining companies carry out their activities in terms of socio-economic and environmental management of territories, not only for its impact on the livelihoods of the communities that inhabit them, but also because many demanders of raw materials -both countries and companies- have set sustainability standards as a prerequisite to establishing business relationships with mining companies, such as the recently declared Sustainable Development Goals by 2030 (UN, 2015). Accordingly, decide underinvest or not to invest in sustainability issues carries risks for mining companies. However, invest much in the wrong way may involve the same risks. Managers are concerned to ensure profits, and therefore they decide carefully how to invest in the areas of production, R & D or marketing. Likewise, they should think strategically about investing in initiatives related to sustainability. This if they really want that those investments in fact help to improve the competitiveness of the company. The mining industry benefits from natural capital that extracts, so it should implement strategies that lead to remunerate such benefit to the territories (Almaguer, 2007). One option is through the transformation of natural capital in other types of non-existent capital or poorly developed in their areas of influence. In this way, the value generated by the extraction of underground resources is shared and additionally contributing to improving the quality of life of the communities. Historically, mining industry has been into several problems to achieve this, which represents one of the aspects that has most influenced the current reputation of mining industry in some regions of Latin America. Many communities, local governments and civil society organizations continue to associate this activity with the destruction of the social fabric and ecosystems in the territories, and their opposition against companies working in the areas has led to affect the operational continuity of many projects (Hamann, 2003; Prno and Scott, 2012; Slack, 2012)."

Jan 1, 2017

By Dennis R. Twining

Recently a mining analyst for a major bank called me to say that during his travels he had encountered an electric utility interested in a new uranium supply. Since we produce uranium as a by-product of phosphate operations rather than as a primary product, he assumed we simply sold our output in the spot market and that a new prospective purchaser would be of interest to us. This assumption was incorrect; the uranium had already been sold on a long term basis at terms more favorable than the currently depressed spot market. From the outset our approach to the marketing of uranium was based on the principle that by-product marketing is not unlike primary product marketing. This was particularly appropriate in the case of uranium, as we were planning a considerable technical and capital commitment to a new business. This illustrates: that the fundamental principle in by-product marketing is to follow a primary product strategy; that the terms "by-product" or "co-product" are creations of accountants; that they have no place in marketing decisions! Traditionally, the term "by-product" has implied that only a secondary marketing effort is required. Recent history has contradicted that view by demonstrating that by-product values can have marked impact on a mine's revenues and costs. In fact, by-product values can spell the difference between success and failure.

Jan 1, 1983

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980