Search Documents

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By James A. Clum

The shift to lower grade iron ores, e.g., magnetic taconites, resulted in a shift towards agglomeration practices which could effectively deal with the fine particle sizes generated in the liberation and concentration processes. If the iron bearing particles are not extremely fine, e.g., -1/2 in + 100 mesh, sintering is an adequate means of agglomeration.(1) For the more dispersed ores which result in fine concentrates (more than 80%,-325 mesh), the fine particles must be agglomerated by mechanical means before final hardening, e.g., pelletizing.(1) In the pelletizing process, the essentially mechanical step of balling is extremely critical since the strength of the pre-fired pellet determines the firing conditions. The ability of the proper amount of moisture to hold together a ball of the very fine ore concentrate particles has long been recognized. It is a charac¬teristic of the reaction at the interface between the ionic solid of the ore concentrate and the polar water phase which overlays the solids. The strength in such moisture laden balls, the green strength, is a strong function of the water content (Figure 1) and thus deteriorates rapidly for either a small excess or a small deficiency of moisture. For purposes of commercial practice, the control of green ball handling properties by accurate control of ball moisture is too demanding. Moreover, as the ball is heated towards its hardening tempera¬ture, e.g., 1300'C, there is a substantial drying reaction which would lead to such a low dry strength of the ball that it would not support its own weight much less the weight of other balls in a firing furnace.

Jan 1, 1976

By Richard Collins

The projected depletion and the increasing costs of petroleum and natural gas along with the public and governmental resistance to nuclear energy have caused coal to emerge as one of today's answers to both our short term and long term energy needs in power generation. In order to satisfy this need, major increases in coal production are mandatory, thus requiring more and higher capacity coal transfer terminals. The logic for selecting coal as the major fuel for power generation is based on many different reports on the existing and potential energy sources, which include petroleum, natural gas, hydropower, solar, geothermal, and nuclear. The following is a brief synopsis of these reports for each type of energy.

Jan 1, 1978

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Abhiram Kumar Verma, Soumya Ranjan Mallick

Generally, waste such as soil and sandstone is used in mines for road construction or haul roads. In many such mines, it is challenging to design haul road pavement to match the dumper capacity. This paper investigates overburden soil to find its utility as a pavement material. It is found that overburden soil is unsuitable pavement material without stabilization; hence, nine composite materials are developed using overburden soil and RBI. Physical, mechanical and microstructural properties of unstabilized and stabilized soil are determined. Statistical analysis is carried out to assess the effect of soil type, RBI and curing period of strength characteristics of unstabilized and stabilized soil. ANOVA tests assess the influence of RBI percentage on soil geotechnical properties, and regression relations are developed. Two-way ANOVA shows the effect of RBI and soil type on soil geotechnical properties, whereas one-way ANOVA shows that the influence of soil type is more than the RBI. The regression relation is developed for CBR, UCS, Poisson’s ratio and modulus of elasticity with a good correlation coefficient. The performance of RBI is more with the finer material and reduces with an increase in the size of soil grains. The performance of the developed composite is better than the earlier developed composite based on overburden with fly ash, lime kiln dust, lime or clinker.

Mar 19, 2024

By Leon Y. Sadler

Equations which predict the unsteady-state response of the continuous froth flotation cell to changes in operating conditions are necessary for the rational design of an automatic flotation cell control system. Unfortunately application of automatic control to froth flotation separation equipment has lagged behind application to other types of separation equipment (for example distillation columns, absorbers, liquid-liquid extractors, etc). This may be due partly to the unavailability of suitable mathematical models for predicting the dynamics of continuous mechanical froth flotation cell. This paper presents the results of a comparison of four dynamic flotation models (in transfer function form) using the same set of unsteady-state continuous flotation data. One of the transfer functions tested has been presented previously in the literature (1), another (2) has been accepted for publication, and two are given here for the first time. In addition, data are presented which confirm earlier findings that the mixing in the rotor-stator type cell is nearly perfect. The specific purposes of this paper are to: (1) provide the automatic control systems designer with several alternative dynamic mathematical models of the continuous mechanical froth flotation cell (2) give some idea of the relative a¬bility of each model to predict unsteady-state behavior by fitting each model to the same set of experimental stimulus-response flotation data and (3) provide more insight into the macro-mechanisms prevailing in the continuous mechanical flotation cell. The dynamic models which are presented and tested here all relate the time variation of the concentration of a given floatable mineral in the tailings to a time-dependent disturbance in the same floatable mineral concentration in the feed to the flotation cell.

Jan 1, 1972

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

A PDP 11/34 computer has been inter- faced to existing instrumentation in a 400 tph rod-mill/ball-mill grinding circuit and programed with a Kalman filter to estimate several unmeasured variables. A dynamic two-size- fraction model of the circuit is used to predict the complete state of the circuit including particle size distributions around the circuit, mass holdups and flowrates, the ball-mill grinding rate, water additions and cyclone parameters. Online measurements of sump level, slurry densities and product particle size are used to update the model values sequentially on a 20-second interval. This procedure results in optimal estimates of circuit variables given the relative reliability of measurements and the accuracy of the model.

Jan 1, 1983

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

By Liangguo Kang

Coal, as one of the vital sources of energy in China, has raised widespread concerns regarding its safety issues amidst the country’s economic growth driven by coal. To address this concern, this study employed the Kuznets curve, multiple linear regression, and data envelopment analysis models to investigate the impact of Chinese coal economic development on coal mine deaths from 1992 to 2021. The findings revealed a clear correlation between the Chinese coal economy and coal mine deaths. Specifically, per capita coal output, the death rate per million coal tons, and the death rate per hundred thousand persons exhibited positive, negative, and negative correlations, respectively, with the growth of coal income over the past three decades. Moreover, when the coal workers and coal output factors remained unchanged, the income of coal demonstrated a negative correlation with future changes in coal mine deaths. Notably, with three decades of coal economy development, substantial improvements in coal mine safety have been observed in China. Consequently, this research provides valuable insights for formulating safety measures and policies in coal mines across different economic levels, as well as a useful framework for assessing safety development in the coal industry.

Jan 20, 2024

By J. Morris, R. Sellaro

Petro-diesel is a common collector for coal flotation, but the partitioning of diesel range organics (DROs) in process streams has not been widely studied. Preliminary research suggested that under normal dosing schemes total residual DRO contents in process waters should be limited to the sub-ppm water-soluble fraction (WSF). Further, polycyclic aromatic hydrocarbons (PAHs) should partition proportionately with DROs. The purpose of this study was to confirm these findings in laboratory flotation tests. Total DRO and specific PAH contents were measured in the waters associated with the concentrate and tailings streams. The results show that concentrate waters consistently had higher amounts of DROs than tailing waters. Moreover, the DRO contents in both streams generally increased with increasing diesel dosage. In line with preliminary research, DROs appeared to be limited to the WSF, and PAHs tended to partition proportionately with DROs. Under typical operating conditions, it appears that residual DROs should not present an environmental concern, but conditions should be avoided that allow significant overdosing of diesel.

Jan 1, 2014

By Ryan Marsters, Adam Pring

The Rawah Ditch is a mountainous water supply diversion which supplies Larimer County, Colorado with water since 1903. The ditch includes two historic tunnels excavated by drill and blast through a gneissic rock buttress. Both rock tunnels were failing with annual convergence. After a snowshoe-accessed eld investigation, nite element modeling, and an alternatives analysis, a diameter DE pipe was inserted within each tunnel and the annulus lled. The proect was implemented in an Alternative Delivery contract lasting ve months from eld investigation through procurement and construction.

Jun 23, 2024

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By Matthew Deutsch

A common casualty of modern open-pit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow, and not minable with realistic equipment. In this paper, all of these problems are addressed by encoding these three fundamental open-pit mine optimization problems as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are non-linear and may guarantee the optimality that metaheuristics cannot.

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By Brian J. Gorva

The key objective of forming a cartel is to increase profits to members of the cartel by taking the following action: a) control output; and b) control price. However, while attempting to obtain monopoly profits the cartel members have to contend with costs associated with cartelization and such costs include the following: political costs; the cost of coordinating output and price; organizational costs (such as cheating); and administrative costs (such as the cost of attending cartel meetings). The objective of commodity exchanges is to provide an open, free market where buyers and sellers may openly complete transactions and pricing information can be immediately disseminated. These transactions include the following: a) to provide facilities for "hedging", or transferring price risk from buyers and sellers of physical commodities to "speculators" through the medium of buying and selling futures contracts, and b) taking physical delivery of metal on due dates.

Jan 1, 1983