Search Documents

By Zhongran Dai, Nan Hu, Jianhong Ma, Hui Zhang, Zhihua Zhong, Han Zhou, Feng Li, Yonggen Qiu, Yang Ding, Yingchun Yang, Dexin Ding

In the traditional chlorination roasting-water leaching-solvent extraction process for the extraction of rubidium-bearing ore, Rb leaching from the ore and calcium removing from the leachate are conducted separately, and this results in the complicated process and high energy consumption. In order to integrate the Rb leaching and calcium removing processes, Rb-bearing polymetallic ore was firstly treated by chlorination roasting, it was then leached in a micro-reactor with raffinate, and the calcium ions in the leachate were removed in the reactor as carbonate precipitates by passing CO2 at certain pressure into the reactor. The effects of raffinate alkalinity, CO2 pressure, and CO2 reaction time on Rb leaching rate and calcium removing rate were investigated. The experimental results show that when Rb-bearing polymetallic ore was leached for 90 min by stirring with raffinate with 1.125-mol/L alkalinity, and the pulp was made to react with CO2 at 0.8 MPa for 15 min, the Rb leaching rate and calcium removing rate amounted to 92% and 98.2%, respectively. This integrated process including Rb leaching from Rb-bearing polymetallic ore and calcium removing from leachate could simplify the process for the extraction of Rb-bearing ore and increase its economic benefits.

Sep 27, 2023

"History - How did you get into mining and involved with SME?Unlike many past presidents, I do not come from a mining lineage. I liked math in high school and believed I wanted to be an engineer. I told my math teacher that, and he laughed in my face. I believe that humiliation is what carried me through engineering school. At the time my ability to go to college relied on how inexpensive I could make it. My brother told me that there were a lot of scholarships in mining engineering, and I should apply to mining schools. As usual, he was right and I was off to the University of Idaho to study. My first summer break I got a job with Hecla at a mine in Arizona. I was a laborer on a shotcrete crew. I knew after the first summer that I loved underground mining, and I never considered changing disciplines. Looking back, I was working in miserable conditions (hot, humid), on a miserable job (shotcrete), where I got injured, and two summer student roommates died in a car accident on the commute home after work. I had every reason to hate the industry, as I had seen virtually everything bad about what we do. But I didn’t, I loved it. I said I was good at math, I never said I was smart.I joined SME in college because I was told to by the head of the mining school, Dr. Jack Hoskins. You did what Jack told you to do. I got involved because I went to an annual meeting and the papers in the underground sessions were terrible. I refer to bad papers as the “Tensile strength on cable bolts in sub-arctic regions on Tuesday” papers. Real snoring fodder. I don’t remember who I was complaining to, but they told me to quit my grumbling and fix it. So I chaired a session, and tried to get only good quality papers, something that has been my mantra for years with the Mining & Exploration Division. I also volunteered to help the local sections too. Then one day I woke up as president.What is your opinion of the health of the mining industry?The mining industry is in bad shape. Coal is under attack and will likely never recover to its former greatness. Our President has banned new coal leases, and the state of California is forcing people it does business with to divest their interests in coal companies. And that all happened in just in a few short weeks this January. Usually in America you get a trial before you are given a death sentence, but not with coal."

Jan 1, 2015

By C. H. Cheh

The amount of fines in run-of-mine coal has been increasing and coal quality has been deteriorating as a result of the increased use of mechanized and continuous mining methods. Removing the mineral matter and pyritic sulfur from coal prior to combustion will lower transportation costs, improve power plant performance and reduce sulfur dioxide emissions. Since physical cleaning methods can only remove individual particles of mineral matter and pyrite, it is necessary to crush and grind coal to fine sizes to separate these contaminants so they can be removed by deep cleaning processes. The increased portion of fines in run-of-mine coal together with attempts to increase the mineral matter removal efficiency have stimulated interest in fine coal cleaning technology. However, there are many problems to be solved before fine coal cleaning can be applied to power plant coals. These problems include: 1. coal cleaning plant capacity is reduced when conventional cleaning circuits are modifies to deep clean coals; 2. existing equipment and technology is not suitable for cleaning fine coal; 3. coal recovery is reduced; and 4. fine coal is difficult to dewater, dry, handle, transport and store.

Jan 1, 1982

By O. A. Bascur

In recent years, metal-producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Transformation to a digital plant can fundamentally revolutionize how industrial complexes operate. The abundant and growing quantity of real-time data and events collected in the grinding and flotation circuits in a mineral processing plant can be used to solve operational issues and optimize plant performance. A grade recovery model is used to identify the best operating conditions in real time. The strategy for increasing the value of instrumentation in current plants is reviewed. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut size to reduce metal losses in the flotation circuits. Sensors in flotation circuits enable an estimate of the recovery and determination of the optimal froth depth and aeration using an air hold up flotation model. A strategy of classifying data for on-line generation of insights to using operational intelligence tools is described. The implementation of a recovery/grind strategy with industrial examples in non-ferrous mineral processing is presented.

By Patrick Browne

Drilling programs and the study of active geothermal systems have shown that the reservoir rocks in many fields contain minor quantities of base and precious metals. Commonly, base-metal sulfides occur in the subsurface but, where present, Au, Ag, Hg, As, T1 and Sb rich precipitates deposit near, or at, the surface. Although in some fields (Geysers, Larderello, Tongonan) some of the ore minerals (and others) are relict, there is evidence that they are now depositing in a few systems. Recent work on active hydrothermal systems in New Zealand shows that: (1) Sphalerite, galena, chalcopyrite (forming veins and disseminated discrete crystals) plus rare pentlandite, cobaltite and arsenopyrite, occur at Broadlands, NZ. Rare quantities of base-metal sulfides also occur in cores and cuttings from the geothermal fields of Waiotapu, Kawerau, Tauhara, and Ngawha. Further, Kakimoto (1983) has identified cassiterite, native silver, and trace gold in cores from Tauhara, in the south-eastern part of the Wairakei field. Bore temperatures at the depths from which these minerals were recovered are mostly between 220° and 300°C, but at Broadlands are locally as low as 120°C. The host rocks are Quaternary talc-alkali, silicic lavas and pyroclastic rocks, andesites, dacite and deep Mesozoic greywackes and argillites; however, there is no obvious relationship between mineralization and stratigraphy, permeability or well output. (2) The deposition of amorphous precious metal precipitates (Au, Ag, Hg, As, Sb, T1) from hot springs and well discharges has taken place at Broadlands, Waiotapu and Rotokawa; it also occurs at Kawerau. (3) Water discharging from Frying Pan Lake, Waimangu, is presently depositing siliceous sinter containing up to 4.1% tungsten. A characteristic of mineral-depositing fluids in the New Zealand geothermal fields is their very low salinity (total dissolved salts of 3000 ppm or less but with high CO2); they are of near- neutral alkali chloride composition, although water discharging from Frying Pan Lake has a pH of 4.5, and very low metal contents. Very effective concentration processes (10 times for gold at Broadlands) must occur: in the subsurface these include boiling and rapid cooling but near, and at, the surface, mixing of waters of different pH seems to dominate. In particular, descending acid condensate, derived from separated steam and oxidation of H2S mixes with its parent alkali chloride water, resulting in precipitation of amorphous ore metals. Base-metal sulfides also occur in veins and as disseminated grains in geothermal fields at Tongonan, Leyte and Southern Negros, Philippines. These fields have a porphyry-type setting with host rocks of Miocene andesitic lavas and pyroclastics intruded by diorites so that the fields have undergone complicated thermal histories before cooling to their present base temperatures of about 325°C. Precious metals have precipitated from waters from some wells (Leach, pers. comm.) but they do not, as yet, form ore-grade deposits.

Jan 1, 1984

By J. Lancaster

World demand of sulphur-in-all-forms (SAF), which in 1985 is estimated to total 57.5 million tonnes S equivalent, is expected to increase to 77.6 million tonnes S by the year 2000. Key factors are the evolution of sulphur demand in the USSR, China, and the developing countries notably India, Brazil, and the countries in North Africa and the Near East with vertically integrated phosphate industries. Brimstone will remain the dominant sulphurous raw material notwithstanding the progressive increase in the supply and use of sulphur in other forms resulting mainly from the enhanced recovery df pollution sulphur and the increased use of sulphur in pyrites in those countries with this sulphur resource. Sulphur demand for phosphate fertilizer manufacture is expected to have the main impact on world sulphur demand, but in contrast to the industrially advanced countries where non- fertilizer sulphur use is not expected to increase measurably, this demand sector is expected to be of some importance in those developing countries with dynamic economies and in the centrally planned economies of East Europe and the Far East.

Jan 1, 1986

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Chloride ions and their interactions with two organic smoothing additives – Cyquest® N-900 and HydroStar® 4208 – during copper electrodeposition were explored using cyclic voltammetry and electrochemical impedance spectroscopy. The results revealed that chloride ions, up to a concentration of 40 mg/L, depolarized the copper deposition reaction. A combination of chloride ions and Cyquest N-900 inhibited the depolarization reaction during copper electrodeposition. It is proposed that the chloride ions acted as bridging ligands between copper and Cyquest N-900. Addition of HydroStar at a concentration of 2.5 mg/L depolarized the copper deposition reaction when no chloride ions were present. This behavior did not change with the addition of chloride ions at the concentrations tested, indicating that chloride ions and the polysaccharide do not interact.IntroductionElectrowinning is a major production method used to obtain high-purity copper. In modern tankhouses, copper is electrodeposited onto stainless steel blanks and then stripped, washed and bundled for delivery. Significant improvements in the quality of electrowon copper have been made over the last few decades. Additives, temperature, current density, electrolyte concentrations and agitation are known to influence the quality of copper electrodeposits (Jenkins and Eamon, 1990).The influence of chloride and organic additives on copper electrodeposition has been the subject of considerable research. The addition of small quantities of chloride and organic additives has been recognized to significantly improve the properties of copper electrodeposits. These additives are critical in the prevention of dendrite growth and the production of smooth, dense cathode deposits.Chloride ions have been reported to catalyze the copper reduction reaction and assist in the production of uniform deposits (Lakshmanan et al., 1977; Sun and O’Keefe, 1992). Moreover, it is generally agreed that chloride ions depolarize the copper deposition process at low (several millimolar) chloride concentrations. This is because chloride ions catalyze the reduction of copper (II) ions to copper (I) ions (Cu2+ ? Cu+ + e-) in the rate-limiting step of this process (O’Keefe and Hurst, 1978; Ilgar and O’Keefe, 1997; Hebert, 2005; Shao, Pattanaik and Zangari, 2007)."

Jan 1, 2016

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By R. Addison

This is the story of the Carlton Mill. But first-a little geography. For those who do not know where the Carlton Mill is, or, perhaps, have only a vague idea, its location is indicated in Figure 1. The plant is situated on the road between the two old mining towns of Cripple Creek and Victor, 10 the west of Colorado Springs. From Denver, it's about 110 miles by road. The story of the Carlton Mill began with the discovery of gold at Cripple Creek in 1890. This discovery set off a major boom such that, by the turn of the century, there were 450 separate operating mines in the district. Gold production boomed early and declined rather rapidly as indicated by the graph in Figure 2. Significant factors affecting production are shown on the graph-the raising of the gold price in 1934 from $20.67 to $35.00 per ounce and the government executive order L-208 in 1942 requiring the closure of all gold mines.

Jan 1, 1983

By S. W. Nicholson, L. G. Woodruff, K. J. Schulz, W. E. Cannon

The 1.1 Ga Midcontinent rift of North America has many similarities to the geology of the Voisey's Bay region in Labrador and the geology of the Noril'sk region in Siberia. These similarities include the hosting of large volumes of sulfur- undersaturated and trace-element-enriched basalt, having igneous centers characterized by crustal contamination, being characterized by metal depletions in some mafic units (an indication of prior sulfide segregation) and having known occurrences of Ni-Cu sulfide mineralization. These similarities along with new geophysical data and refined models for Ni-Cu sulfide deposits suggest that the Midcontinent rift probably contains undiscovered Cu-Ni [±] PGE sulfide deposits, some of which could be the size and grade of a Voisey's Bay or Noril'sk deposit. In particular, intrusions and related feeder systems that occur in northern Michigan and Wisconsin, as well as to the southwest along the rift margin, deserve serious examination.

Jan 1, 1999

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996

By Jean-Michel Rendu

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual fitting of the model is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. A number of interactive methods are described, which are adapted to the modeling of semivariograms in one-, two-, or three-dimensional environments.

Jan 1, 1982

By Walter von der Linden

On April 14, 1975, Consolidation Coal Company began to operate a longwall face in their Shoemaker Mine using shield supports. This was the first time that shield supports were used in the United States (1) 1/. Shortly thereafter, Kaiser Steel Corporation started a shield longwall face at their York Canyon Mine (2). From October 1975 through May 1976, three more longwall faces were commissioned in mines located in south-western Pennsylvania and northern West Virginia. In June 1976, four installations had completed their first panel and two installations had completed the subsequent move to the second panel where coal production is now well under way. During this time (April 75 to June 76) the total number of shield support face operating months, including moving time, was 40 and the combined face advance was approx. 17, 000 feet (5200 m) with face lengths varying from 450 - 550 feet (137 - 168 m). While the shield support experience in the U.S. is still limited on the basis of time and mining parameters, the operating results of all faces have been very satisfactory. New record 24 hr production figures were set and - far more important - long term production figures could be sustained on an impressively high level even when taking face moving time into account. The purpose of this paper is to review the performance of shield type supports in the U.S. and to assess their value as longwall supports for U.S. underground mining conditions with regard to roof control, maintenance, operator convenience, safety and productivity.

Jan 1, 1976

By Patrick Linzer, Lindsay Linzer

By its nature, seismology has been a data intensive field since the first digital computers were introduced in the 1950s. The first empirical models were developed in the same period and are still widely used today, for instance, the Gutenberg-Richter frequency-magnitude relationship (Gutenberg and Richter, 1956). Machine learning (ML) methods make it possible to redefine these empirical models using large datasets and examining considerably more parameters, where their significance to the problem being addressed is methodically and repeatably evaluated using robust statistical methods. In this paper we develop a simple logistic model for the short-term prediction of seismic events above a threshold magnitude from a mine’s event catalogue comprising more than a million events with 14 basic parameters from which a pool of over 830 derived parameters was developed, covering a series of 11 precursory time windows. The logistic model was fitted stepwise using SAS with α = 0.025 for both entry and acceptance. 25 variables from the pool met the acceptance criterion. The findings were surprising in that parameters a rock engineer or seismologist might have expected to be the most significant in the logistic model were not; instead, it was an increase in standard deviation of the immediately-prior seismic magnitudes that carried the most weight, followed by the average maximum source displacement and median apparent volume change. These findings make intuitive sense because the increasing scatter of the magnitude shows an increasing number of large events being recorded that could be indicative of instability in the system that could lead to large events. The model is rudimentary and enormous scope exists for more exploration in terms of data pre-processing, model types, and response variable definitions.

Apr 26, 2022

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By G. Thorsen

An alternative way to the normal practice of precipitation of jarosite, goethite, or hematite for removal of iron from zinc sulphate process liquors/ is to employ the techniques of solvent extraction. The process presented avoids the addition of any external alkali for the extraction of iron by integrating the leaching and solvent extraction steps in a hydrometallurgical zinc plant. By starting the leaching of zinc from the solid zinc calcine material with an organic solution of an acid liquid cation exchanger, the organic phase is loaded with the organic zinc salt from the direct reaction with zinc oxide. The residue from the organic leaching is transferred to a hot acid leach circuit where the remaining zinc oxide and the zinc ferrites will dissolve form¬ing an aqueous sulphate solution of zinc and iron. In the subsequent solvent extraction of iron from this aqueous leach solution, iron is exchanged with zinc from the organic phase. The commercial carboxylic acid Versatic 10 (Shell) is highly efficient for this integrated process of leaching and solvent extraction. The resulting iron-loaded organic phase is heated to 150-200 C in the presence of water whereby the iron will be directly precipitated from the organic phase as iron oxide of high purity and the regenerated organic acid is recycled to the organic leaching step for reloading with zinc.

Jan 1, 1980