Search Documents

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By Richard Komarek

When limestone (Ca03) is calcined in rotary kilns to produce quicklime (CaO), it is not unusual for 10% to 20% of the stone to abrade and emerge from the kiln as quicklime fines (-6.3 mm or -0.25 in.). While there are various industrial processes that can use fines, handling and shipping is tricky and dangerous. Due to the highly caustic nature of quicklime, airborne dust easily bums eyes and skin. On the other hand, money has already been invested in mining (or buying) the raw material and in the equipment and energy needed for calcining. Discarding the fines will not only waste that investment, but add even more cost in transportation and possibly dumping charges. So the question becomes, how can fines best be turned into a revenue-generating asset? Some plants convert leftover quick-lime fines into calcium hydroxide - Ca(OH)2, also known as hydrated or water-slaked lime - for sale into agricultural applications. For farm uses, hydrated lime fines are preferred over quicklime because they are easier to handle. And they are favored over raw limestone fines for their higher concentration of calcium and greater solubil¬ity. From the producer&apos;s viewpoint, quicklime fines are ideal for this use because they go through hydration faster than the larger chunks of quicklime. Those larger chunks, or "pebble lime," are more readily salable and more easily handled, for such uses as steel, copper, aluminum and magnesium production, water waste treatment, chemical, paper, glassmaking and flue gas desulfurization in coal- fired boilers.

Jan 1, 1993

By K. K. Kohli

Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence-induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months&apos; survey, the data collected include 17 longwall panels and 2 room and pillar sections. The data in-each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages.

Jan 1, 1980

By Howard G. Coopersmith

A resource of low grade good quality diamonds has been discovered through the Diamond Company NL-Moonstone Diamond Corp. Joint Venture. A limited bulk sample diamond test of two large kimberlite pipes on the Kelsey Lake Property, Colorado, has been completed. These kimberlite pipes have petrological and mineralogical indications of the presence of diamond. Small diamonds were recovered from surface samples. Drilling and trenching revealed both pipes were complexes of diatreme facies kimberlite. One pipe contains crater facies kimberlite as well. This is the first reported occurrence of crater facies kimberlite in the Province. Approximately 1000 tonnes of kimberlite rock was excavated and processed through a scrubber -HMS -Sortex -Grease Plant. Significant diamonds were recovered. The diamonds were generally of good color and clarity, with many being in the gem and near gem categories. Grades are considered low however. Additionally, a small potential resource of alluvial diamonds is present.

Jan 1, 1991

By R. L. Hills

America&apos;s industry uses about 44% of the total energy consumed by the nation directly as fuel burned in industrial plants or indirectly as fuel burned by utilities to provide electric power. In addition, industry requires raw materials or feed stocks derived from fuel sources or having fuel value. This represents about 11% of total U. S. energy consumption, bringing industry&apos;s portion to about 55%. Adding that portion of energy consumption required by the transportation sector to move raw materials, intermediates, and finished products, the total energy impact of industry approaches 213 of total U. S. consumption. It is obvious that American industry has the largest share in the task of balancing energy demand and supply. What are we going to do? -- We must increase the supply of energy and increase the beneficial results obtained from each unit expended. Both avenues, unfortunately, are limited in extent and speed. Increases in supply cannot occur without drastic and permanent increases in cost. These increases in cost are un- desirable and inflationary but do provide incentive for the rational businessman to expend the effort and money required to improve the effectiveness of energy in industry.

Jan 1, 1975

By David Beck, Eko Wibowo, Hendri Silaen, Andres Sugiyanto, Karl Llewelyn

PT Freeport Indonesia’s Deep Mill Level Zone mine is one of the deepest block cave mines in the world and is in mountainous terrain in West Papua, Indonesia. The mineralization is hosted in a skarn deposit in a structural setting that is complex at the footprint, mine and regional scale. Large seismic events and significant episodes of rapid rock mass deformation are potentially critical geotechnical risks during this ramp-up stage of mining. Understanding the interaction between stress, strain, rock mass strength and geological structures is essential to minimize the hazard and engineer control measures to help ensure the safety of the employees while achieving production targets. This paper discusses how the seismicity and excavation damage have been shaped by the interactions between the mine and geological features, and how this affects strategic mining decisions. Additionally, the paper presents a summary of the mitigation measures used for mining the DMLZ in the safest and most productive way. These include improvements to geotechnical characterization of rock mass and structure, dynamic ground support designs, production scheduling for desirable cave propagation and a seismic monitoring system with re-entry protocols.

Apr 26, 2022

By E. R. Bauer

The trend in underground room-and-pillar coal mining is to employ remote-control continuous mining machines and extended cuts, 12 m (40 ft) deep or more. This system of coal extraction, adopted by over 435 mines, can create additional worker-safety hazards. To address the ground control and worker-positioning hazards, a combination of statistical analyses and numerical modeling was conducted. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the Coal Mine Roof Rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling to predict roof displacements during extended-cut mining was completed. The paper describes the results of these studies and their impact on the safety of extended-cut mining.

Jan 1, 1999

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By P. Kim Carroll, D. Nick Tiffany, Doyl M. Fritz

Thunder Basin Coal Company received the 1987 Wyoming Excellence in Surface Mining Award for construction of the State&apos;s first major sediment control reservoir to be designed using the new settleable sol ids standard. Use of this standard resulted in construction cost savings of more than $250,000; reduced water quality monitoring; enhanced downstream channel stability because of more natural sediment loading; allowed simultaneous establishment of permanent waterfowl and fisheries habitat; and provided a quality recreational site. This article will address factors associated with the design and construction of that sediment reservoir and the benefits that were realized. (Note: This paper was originally published in the proceedings for the 1988 National Symposium on Mining, Hydro1ogy, Sedimentology and Reclamation held in Reno, Nevada, December 5-9, 1988.)

Jan 1, 1989

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure of roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations and trial-and-error testing. Both the prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh, PA before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By W. G. Cornwall

The mining field, inclusive of the treatment plant is located in the foothills, five miles inland from the northern coast of Viti Levu, the largest and most important island of the Fiji Group. Gold and silver occur as tellurides, associated with the sulphides, and as minor occurrences of electrum.

Jan 1, 1975

By Michael Murphy, Gamal Rashed, Brent Slaker

Many underground stone mines in the United States operate on multiple mining levels. The effects of interburden thickness, pillar offset between mining levels at various depths of cover, and in situ stress conditions are poorly understood. Pillar offset is the degree to which pillars are not columnized or stacked. In this study, calibrated numerical models are used to examine limestone pillar stability in these conditions. Also, the critical interburden thickness required to minimize the interaction between mining levels is explored. The model results show that there is interaction between numerous factors that control the stability of stone pillars in multiple-level conditions. The highest degree of local pillar instability occurs when pillar overlap ranges between 10 and 70 percent. The highest degree of stability occurs when pillars are stacked.

Jan 1, 2023

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

By R. H. W. Chadwick

We in Kennecott are well aware that Alaskans are interested in the progress of our project at Ruby Creek. We would very much like to be able to present you with a final report at this time and tell you about a new mine. I&apos;m afraid, however, that it will be several years at best before such a report can be made. This, then, is an interim report to describe briefly some of our findings to date, and to acquaint you with some of the problems, both geologic and economic, which must 5e resolved favorably before we can talk about a mine. There are several things about this project which make it unusual and interesting to those of us who have been connected with it. Firstly, there is the fundamental importance to Alaska, in the present stage of its economic history, of any undertaking which offers promise of turning a natural resource into a competitive export product. I am sure all of us would get a lot more satisfaction out of having a part in bringing in a new mine in Alaska than we would out of adding another one to the long list in, say, Arizona.

Jan 1, 1960

By Christopher B. Kapes

To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.

Jan 1, 1994

By E. A. Zawadzki

The problem of pollution of water by mine drainage is at least as old as the mining industry itself. However, research on the formation, composition, treatment, and abatement of mine water is a relatively recent historical event. At Bituminous Coal Research, Inc., acid mine drainage control has been an important area of work since 1944, at which time BCR began sponsorship of research at West Virginia University. The work at West Virginia University involved a detailed study of the acid mine drainage problem and led to the identification of iron oxidizing bacteria as important factors in the formation of acid mine water. The results of this research were summarized in 1954 by Temple and Koehler (1) who concluded that "no practical solution for the problem" of controlling acid mine drainage is yet known.?

Jan 1, 1967