Search Documents

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By Sunny Murmu, Gnananandh Budi

One of the most significant concerns in longwall ground control is the instability and failure mechanism of the coal wall. The current research uses FLAC3D to simulate panel 1 of the Adriyala Longwall Project, India, in order to evaluate the distribution of vertical stress and material failure mode, in and around the longwall face. Additionally, three distinct criteria are used to evaluate coal wall spalling: vertical stress distribution, maximum shear strain, and residual cohesion. A novel algorithm is also proposed to appropriately capture roof bed caving, shield installation and advancement, and coal extraction from the face. The findings of the modelling show that progressive longwall extraction creates an elliptical stress relief zone around the excavation void. During the peak stress phase, the height of the stress relief zone is greatest, whereas the width is highest during the main fall phase. As mining advances, the coal wall at the face line appears to lose its stress-bearing capability. Shear failure was the most common coal wall failure mode. Maximum spalling depth (MSD) and longwall face spalling index (LFSpI) were used to measure the extent and volume of coal wall spalling in FLAC3D. For panel 1 of the ALP mine, the MSD, and LFSpI were determined to be 3 m and 90.5 %, respectively. The mode of coal wall spalling was expected to be total or fragmented failure. The field observations and the numerical modelling findings were in good agreement. The compressive strength and deformation modulus of the immediate roof appear to have a substantial role in coal wall spalling. The results of the proposed numerical simulation exercise can help strata control engineers better detect the risks of coal wall spalling and enhance face control for safe and productive working environment at the longwall face.

Aug 8, 2023

By I. R. M. Chaston

Abstract. This paper puts forward the concept of 'radial' plant layout where all crushing, milling and treatment operations are preferably concentrated in one central area and these separate stages are connected by radiating conveyors to and from outside storage areas. This system is contrasted to the more customary system of 'linear' plant layout where the crushing, milling and often the treatment operations follow one after the other in separate buildings. The radial system simplifies and improves contral and supervision to a very considerable extent and can lead to a form of continuous plant operation with the separate sectors shutting down in succession for necessary maintenance while maintaining the overall plant operation. The paper is illustrated with example: from past and recent diamond treatment plant practice in South Africa which demonstrate the reduction in plant labour achieved by this system. Previous objection to this type of layout on the grounds that it inhibited plant expansion are shown to be unwarranted. Radial Layout for Increased Treatment Plant Productivity A great deal of time and trouble is spent by highly qualified and experience( metallurgists in developing the right treatment process for a given ore. This process is then often expressed in a treatment flowsheet of the type shown in Fig. 1 which shows a typical diamond plant. This flowsheet, when completed, is commonly handed over to the mechanical engineers who then design the layout of the equipment indicated on the flowsheet and produce the working drawings upon which the detailed construction of the treatment plant will be based. It is an unfortunate fact that the tedious and time-consuming juggling of equipment and inter-plant transportation is often left to hard-working draughtsmen who, however capable' in their field, lack practical experience in the day-to-day operation and maintenance of the treatment plants they design. As a result many plants have been produced which, while they satisfy the requirements of the flowsheet with minimum capital requirements, cost far more than should be necessary to op¬erate and maintain. It is often possible to change individual items of equipment which do not achieve the performance required of them, but it is usually extremely expensive to change the basic layout of the plant if this should be found to be unsatisfactory. It should therefore be recognised that great care and attention should be spent on consideration of the basic layout of any treatment plant and that the views of both designers and operators should be fully regarded before settling upon the inevitable compromise dictated by the varying requirements of process-engineering and economics. It is unfortunate that this important subject receives such scant regard in the standard ore dressing text books and hand-books, being usually dismissed in a few paragraphs.

Jan 1, 1977

By L. C. Morales

During my College days in Mexico City, my Mineralogy Professor used to say "Mexico is the Horn of Plenty, rich in minerals, and it is easier to say which minerals are not found instead of stating all that exist. He said that the only ones missing are bauxite, diamonds and titanium ores." Today, twenty years later, a rutile mine in Oaxaca is in successful operation. Mexico has an area of approximately two million square kilometers, with volcanic activity, large shores and mountainous areas reaching as high as 6,000 meters above sea level. These conditions are favourable for most mineral deposits, some -of commercial value and others as a source of mineral samples only. (fig. No.1) In addition to vast mineral wealth, Mexico has -another valuable asset in .his people. Even before the discovery of America, natives were successfully mining metals, and during the Colonial --days, the mineral deposits were mined to increase the wealth of Spain, and it increased the --knowledge of mining. All this experience was passed along from generation to generation, and created a tradition of mining and minerals processing engineers, that currently account for approximately 182,000 persons supported by mining related activities.

Jan 1, 1994

By CADEN VITTI, Barbara J. Arnold

Mine tailings, the byproduct of mining and mineral processing, are increasingly mass produced as a result of increased demand for metals and minerals as well as the advancement in technology that allows for the exploitation of lower-grade ores. Lower grades can increase the volume of tailings that may contain new gangue minerals that should be evaluated for the presence of critical minerals and other valuable metals. The practice of reprocessing, while relatively new, is crucial to reducing environmental damages, obtaining valuable critical minerals from waste, and contributing to more sustainable repurposing and disposal methods. With the increase in tailings dam failures in recent years, there is a large motivating factor in remining and removing the potential hazard to benefit the safety of potentially impacted communities. In analyzing the perspectives of various domestic and international studies, this literature review will determine the feasibility of reprocessing and reutilizing mine tailings waste for a more sustainable future while exploring current practices that have benefitted ecosystems and communities.

Jan 1, 2022

By QUANWEN PU, Yonggang Wei, Bo Li

The spent catalyst is one of solid waste resources, which contains precious metals with considerable recovery value. However, due to the different compositions of catalyst, the recovery process is difficult. Most of the catalysts are supported by alumina which has good alkali-soluble properties, while platinum is insoluble in alkali. Platinum is enriched by pressurized alkaline solution which is a kind of hydrometallurgical process. The novelty of this study is the separation of alumina and platinum from the spent catalyst and the enrichment of platinum in the solid phase. In this study, a leaching process using NaOH as leaching agent under high temperature and pressure was employed. The effects of alkali concentration, leaching temperature, leaching time, and liquid–solid ratio on leaching efficiency were investigated. The optimum process conditions were determined as follows: alkali concentration of 240 g/L, temperature of 200℃, pressure of 1.20 MPa, time of 1 h, liquid–solid ratio of 5:1. It was concluded that the leaching rate of alumina can reach 99.69%. The content of platinum increased from 0.1749 to 21.12%, the loss of platinum was 3.39%, and the enrichment ratio of platinum increased by 120.82 times. The leaching kinetics of alumina was studied based on the shrinkage core model. The activation energy of alumina leaching is 19.53 kJ/mol, and the leaching process is controlled by chemical reaction. Pressurized alkali solution can not only efficiently leachate alumina from the spent catalyst and enrich platinum, but also reduce the reaction time and increase reaction rate.

Feb 11, 2022

By B. W. Firth

Increasing depth in vertical mine shafts penalises conventional hoists in at least four distinct ways: rope weight becomes limiting; travel time increases; the obstruction of ventilation becomes more serious; and with friction drives, rope wear due to torque is aggravated. Travel speed is limited by instability of poorly sprung conveyances on inaccurately aligned flexible rails, and also by the cost of installed power to meet an inherently peaky demand. These problems call for a review of existing designs, firstly in respect of the furniture (Buntons and guides) obstructing the air flow, and secondly in regard to the hoist running in the shaft.

Jan 1, 1969

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Sergio Godoy P.

The Los Bronces porphyry copper deposit is located in the high Andes of Central Chile. Ore is mined from several tourmaline breccias and from an earlier porphyry. After years of experience in the geostatistical estimation of reserves in different zones of the ore body, we believe that success lies in considering the evaluation as an integrated process beginning with the analyses of the drilling density and sampling methodology, ending with the critically important reconciliation between the estimated and the actually extracted ore, in general, when errors or differences occur, focus is centered in the calculation stages of geostatistics. However, this paper demonstrates that all the evaluation stages are equally important and require the direct and continuous geologic input to ensure the best possible estimate within the frame of the geologic constraints.

Jan 1, 1992

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By Paul A. Rittenhouse

Its a pleasure to be with you this afternoon and to talk briefly on one of my favorite subjects -- the U.S. sulphur industry. As our Chairman mentioned, I have been associated with the sulphur industry either directly or indirectly for the last twenty years, both on the production side and as a consumer. Sulphur, while unseen and relatively unknown to most people, is like margarine ... that ubiquitous spread ... that is yellow and nearly omnipresent in the industrial world. It is because sulphur, in some form, is required in nearly all aspects of our economy that makes its study so interesting to me as a researcher. An analysis of the sulphur outlook requires examination of such industries as fertilizer, paints and pigments, copper and zinc, uranium, petroleum, chemicals, pulp and paper and textiles - just to name a few. Of course, because its use is so widespread and ever-changing it is difficult to develop and maintain a good understanding of the sulphur industry. It is also a problem to cover the industry in a short discussion and to project its really dynamic nature. Hut, if you will bear with me, I will attempt the task. First of all, let me say that sulphur today is a world commodity and to a large extent moves freely in world trade; nearly a third of the world's sulphur or something over 15 million tons in 1974 entered international trade. However, today our interest is in the current changing sulphur picture in the U.S., with particular emphasis on the western part of the country.

Jan 1, 1975

By Im C. J.

The addition of coal preparation plants changed the coal industry during the past. Now it is time co once again improve the quality and types of coal products coming from future coal preparation plants to meet the changing needs of our society. Clean Coal Technology, along with federal support provided, is forcing our industry to provide cleaner coal products for industrial applications. Liquid fuels from coal is just one of many new products from a coal preparation plant that has a ready market in the transportation sector. UCC Research Corporation is developing these new liquid coal products and this paper will describe the progress and the new slate of coal products to be provided from future preparation plants.

Jan 1, 1989

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By Fei Chen, Xun Xu, Dezhong Kong, Yu Xiong

We address the problem of rib spalling caused by mining-induced roof movement. This problem affects production and safety of the working face. We address this problem by using the 3DEC numerical software to simulate the distribution and evolution regularity of displacement, stress, and the extent of plastic zone in the overlying strata and coal face during the advancing excavation of the 10,905 working face of the mine. Results showed that the first weighting interval of the 10,905 working face is 50 m, and the periodic weighting interval is 20 m. The fractures of overlying strata develop during the first weighting; the vertical stress and vertical displacement of the main roof increase by 45% and 10%, respectively; the vertical stress of the coal face increases by 11%; and the plastic zone in front of the working face increases rapidly. The displacement and stress of the main roof and coal face change periodically during the period of periodic weighting. The variation range during the periodic weighting is less than 30%, but the overall degree is larger than that before the first weighting. Finally, the integrity and rationality of numerical simulation are supplemented and verified by similarity simulation. On this basis, the proposed roof and coal face stability control scheme reduces the maximum horizontal displacement of the coal face from 16 to 4 cm, that is, a decrease of 75%. This study provides theoretical guidance for roof support and coal face stability control of working faces under similar conditions.

Dec 26, 2022

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By James J. Fallon

I'm glad this meeting is being held in New York. First, because the city is close to my home in New Jersey, only 35 minutes from Times Square ..... if I were to come to Times Square between two and three in the morning. Otherwise it takes two hours. But even more important is the fact that all of you good people from around the country and around the world will enjoy the unique experience of that warm friendly atmosphere in the greater metropolitan area, something that you won't see any place else on the face of the earth. Seriously, the greater metropolitan area has been a large part of my industrial, cultural and spiritual experience. There are many aspects of it which I find disagreeable but on net I would rather live in this area, at least for the time being, than any other area of the United States. As a consultant I find contact with financial institutions, corporate headquarters, information sources and a great many production and research facilities a valuable asset to my activity.

Jan 1, 1985

By Jerry Dolph

In September 1855, 55-year-old Noah Spencer Kellogg and his $3 jackass named Bill discovered what was known at the time as a “blow out” of high-grade lead and silver ore. The deposit was located on the side of a North Idaho mountain high above the South Fork of the Coeur d’Alene River. The ore was later assayed at 41,141 g/t (1,200 oz/st) silver. Kellogg named his discovery the Bunker Hill Lode, after the June 17, 1775 Revolutionary War battle of Bunker Hill. A thriving pioneer settlement sprang into existence around the resulting mine’s workings and was eventually— and appropriately — named Kellogg. The peak rising hundreds of feet above the mine’s adit was named “Jack-ass Peak” after Noah Kellogg’s hairy companion.

Jan 1, 1996

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011