Search Documents

By NICHOLAS BELLUSCI, D. Erik Spiller, Patrick R. Taylor, VICTOR BRAMAN

Approximately 30% of the world’s production of soda ash comes from mining and processing of naturally occurring deposits of sodium carbonate containing species. Of these deposits, the largest and most profitable have been the trona beds found near Green River, Wyoming. Processing of trona ores is water-energy intensive, particularly due to unit operations of calcination, dissolution, and evaporative crystallization to wield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale. However, it is speculated that the glass-manufacturing industry, the largest consumer of soda ash, may be able to use a product of a lower grade and consistent level of the insoluble constituents. Thus, pre-concentration of trona ore was investigated using sensor-based sorting, to produce a beneficiated trona stream that would be fed to calcination. The study encompassed preparation of a run-of-mine (ROM) Green River ore sample, selection of 25–75-mm-sized specimens, imaging of the specimens by x-ray transmission (XRT), color, and laser-induced fluorescence (LIF)-based sensors, insoluble analysis of the specimens, and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content existed and that a surface detection-based sensor, particularly LIF, was apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65% separation efficiency and a 70% recovery of trona could be achieved.

Aug 9, 2022

By H. Nagel, A. P. Schissler

"INTRODUCTION Anadarko Petroleum Corporation (Anadarko) owns a region of oil shale properties acquired as part of the original Union Pacific Land Grant of the 1800’s in southern Wyoming. These holdings are greater than 2 million acres and occur throughout the Green River Formation in southwestern Wyoming. One area was prioritized for further study by Anadarko Minerals called the Kinney Rim in the Washakie Basin due to low environmental impact, proximity to infrastructure, high ore grade, and low mining cost. The area is a low-overburden oil shale resource that can be developed using surface mining methods, processed by conventional surface retort, and placing waste rock disposal back on the bench for a design capacity of 10,000 barrel per day. The purpose of this papers is to present the results of environmental analysis and timeline, the mine plan, and surface ore processing to offer a resource-ready energy source.Mineral rights for the Kinney Rim area are owned by Anadarko, the United States Bureau of Land Management (BLM) and the State of Wyoming. Mining of oil shale for this study targets Anadarko owned mineral resources.GEOLOGY The study area is in the Green River and Washakie Basins in western Wyoming. The host geologic member is the Laney Oil Shale. Figure 2 illustrates the Laney shale within a generalized lithologic cross section.OIL SHALE LEASING The proposed Kinney Rim oil shale mining project is located in an area dominated by a 1 square mile checkerboard landownership pattern with every other section typically administered by Bureau of Land Management (BLM) and Anadarko. Surface and mineral ownership is a split estate legal entity. The immediate Kinney Rim mine plan is all on Anadarko sections."

Jan 1, 2015

By W. Miles

Introduction From a historical perspective, bentonite is the common rock term for various uses and applications. Its name originates from water-based muds near Fort Benton used for lubrication of wagon wheels during the 19th century migration to western territories (which are presently part of the United States) when the pioneers ran out of axle grease. From a clay mineralogy perspective, bentonite is composed primarily of montmorillonite, an expandable magnesium aluminum silicate clay mineral. When magnesium occupies an octahedral structural site that usually contains an aluminum atom, a negative charge is created. In order to neutralize negative charges, cations are drawn to the interlayer surfaces between clay mineral sheet structures. Modern applications for bentonite depend on the sodium or calcium cation populations and other characteristics of the clay mineral. When sodium is the dominant cation, the material is also called sodium bentonite, also known as swelling bentonite, western bentonite or Wyoming bentonite. When calcium or magnesium is the dominant cation, the material is called calcium bentonite, also known as nonswelling bentonite or southern bentonite. Swelling bentonite is recognized for its rapid hydration of interlayer sodium and subsequent dramatic expansion up to more than 20 times its original volume. Low shear can then disperse the hydrated sodium bentonite to form suspensions that increase viscosity and suspend solids. However, when shear is subsequently eliminated a sodium bentonite slurry gels. Characteristically, nonswelling calcium bentonite has relatively poor hydration properties and thus low expansion of the clay mineral. When subjected to low shear, calcium bentonite exhibits very little viscosity and poor suspension. Additionally, when shear is subsequently eliminated no more than minimal gelling takes place. The domestic and export markets related to both swelling and nonswelling bentonite are discussed below.

Jan 1, 2007

Newmont has been producing gold from the Carlin Trend for over 45 years. Naturally the focus, scale and complexity of the operations have changed considerably over this time. Newmont discovered and developed the Carlin Main ore body which is located about 32 km (20 miles) north of Carlin Nevada. The property was developed as a one mine one gold mill treatment plant operation which produced about 6,200 kg (200,000 Troy ounces) of dorè gold bars per year. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a dorè bar for sale.

Jan 1, 2012

By J. Hart, P. W. Conrad, S. Rosenthal, R. A. Hogan

The Mining Engineering Department at Montana Technological University (Montana Tech) has a new Mine Safety and Health Administration (MSHA) approved program for Part 46 and Part 48 mine health and safety training. The training program will utilize the facilities and faculty from Montana Tech’s Mining Engineering and Safety, Health, and Industrial Hygiene departments to provide superior mine health and safety training to the mining industry. The faculty of each department includes professionals with experience in safety training and the mining industry. The training program incorporates adult learning techniques and extensive hands-on activities in all training modules. The instruction will exceed MSHA requirements. The resources available on Montana Tech’s campus will be utilized to strengthen the training program providing the mining industry with a world class mine health and safety training program.

Feb 1, 2023

By Christoph Mueller, Grzegorz Tabak

Basing on five years of experience, this paper discusses modern e-drive systems used in underground transport. This covers Energy distribution and cabling principles, inverters and motors as well as auxiliary aggregates. Also an overview of different regimes for battery charging and the energy management and the method of control of the traction are lined out: This means that throttle and brake are not handled separately, but integrated into “longitudinal control” algorithms which assure that a commanded speed is maintained while synchronizing the multi motor systems and taking into account the constraints imposed by e.g. slope grade and battery parameters.

Jun 25, 2023

By M. A. D. Azevedo, J. D. Miller, R. Kobler, E. Mutkowska

Up to 3 million tons of automotive shredder residue (ASR) is generated annually in United States. Plastics are the most valuable component of the ASR material making up approximately 25% of the total weight. In order to reuse these plastics, a selective process is required to separate each plastic, with very high purity and favorable economics. One separation technique, which may be able to selectively recover the plastics from ASR, is flotation. The preliminary flotation results have demonstrated that acrylonitrile-butadiene-styrene (ABS) and polycarbonate (PC) can be selectively separated from the model ASR feed, the PC/ABS/PA 66 system, by appropriate control of the surface chemistry.

Jan 1, 2001

By Andre Balt, Pierre Hofmeyr

It is only recently that automation has been applied to mining analytical laboratories. This paper describes the use of automation in the laboratory analytical process of hard-rock mining and geological samples and slurries in mining concentrator plant process control laboratories. Types of analysis include fire assay, XRF, ICP and wet chemistry. The benefits of automation are reduced unit cost of analyses, greatly reduced staff requirements, higher quality of data and very fast turn-around times.

Jan 1, 2005

By M. J. van der Meulen

"The Netherlands has major resources of sand, gravel and clay, exploited mainly for construction works and the building materials industry. As in most western countries, mineral extraction meets with considerable societal resistance. To this end, Dutch minerals policy aims to prevent extraction by promoting economical use of materials, and the use of alternative (secondary or renewable) materials. Up till recently, it also included a system of production planning to sustain supplies of regionally scarce materials. Dutch policy development is reviewed and discussed in terms of pitfalls and possibilities for mineral planning in general. Promoting secondary substitution has been quite successful, and presents an example. In contrast, the production planning system has been controversial from the start and ineffective as a result, mainly because it attempted to solve supply problems without properly addressing the underlying resistance. For this reason the system is in the process of being abandoned. The full paper will be published in: Petterson, M., McEvoy F, & Marker, B.R. (Eds) 2005, Sustainable minerals operations in the developing world, Geol. Soc. Lond. Special report series, in press. This abstract is reprinted with kind permission of the publisher."

Jan 1, 2005

By Rick Coleman

PT Freeport Indonesia’s (PTFI) latest expansion has increased total mill throughput to 125kt/d (137,700 stpd). The most recent expansion included the installation of a semiautogenous mill (SAG) designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation, including conventional and column cells, and a regrind circuit. All equipment is supported by a modern distributed control system. PTFI’s operations are located in the Ertsberg mining district of Irian Jaya’s Jayawijaya Mountains, the eastern-most province of the republic of Indonesia on the Island of New Guinea. PTFI, the operator, is owned by Freeport McMoRan Copper and Gold (81.3%), the government of Indonesia (9.4%) and private Indonesian investors (9.3%).

Jan 1, 1996

In this work, the crystallization of Carnallite from waste brine of Qaidam Basin in Qinghai province was studied based on NaCl-KCl-MgCl2-H2O phase diagram. According to this study, a new crystallization pathway to recycling waste brine was developed. The carnallite salt was formed by using this technology during the waste brine evaporation. The experiment data shows that 5 tons of waste brine was required to form one ton of the carnallite. The average grade of carnallite prepared by using this procedure was about 19.40% of KCl, 16.92% of NaCl, 28.80% of MgCl2, and 0.82% of CaSO4. This study provides an opportunity to utilization of the waste brine.

Jan 1, 2012

By Bahram Sameit

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past three decades to estimate rock size distributions. These methods utilize a range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specifc to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. It will then describe methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects.

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare's King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement's returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry's balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By Todd Minoski, Matthew McElhinney, Morgan Sears, Craig Compton

In an effort to advance the science underlying ground control engineering, researchers with the National Institute for Occupational Safety and Health (NIOSH) are frequently involved in field studies at collaborating mines. Often, these field studies involve visiting the mine site, instrumentation installation, and data acquisition. Each of these aspects involve potential risks to NIOSH employees. As an organization whose mission it is to promote the health and safety of mine workers, the health and safety of our workforce is paramount. This paper provides documentation of the best practices followed by NIOSH employees who are tasked with visiting and conducting work at underground and surface mines. This includes Mine Safety and Health Administration (MSHA) approved training, mine site specific training, and hazards associated with all aspects of mining that could be encountered by the employee. Additionally, this paper details best practices associated specifically with instrumentation installation including the mitigation of hazards associated with the proper equipment handling, drilling, and the mine environment. The information showcased in this paper can be used as considerations for industry practitioners such as mine operators, consultants, and academic researchers engaged in the installation of instrumentation in the field. Furthermore, the best practices detailed in this paper can be used as a foundation for agreements made between mine operators and researchers to ensure safety procedures will be followed while on mine property. This will result in enhanced safety of both researchers involved in field studies as well as mine employees tasked with assisting and accompanying those researchers.

Feb 1, 2024

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015

By A. Roper

Since the Toronto conference in May 2002, the International Council on Mining and Minerals (ICMM) has made progress on the road to sustainability. Fifteen of the world?s largest mining and metal producing companies and twenty-five associations have made a long term commitment to ICMM to improve the environmental and social sustainability of their activities. Sir Robert Wilson (Rio Tinto) assumed the chairmanship of ICMM in October 2002. By December 2002, the Council had approved a Strategic Vision and an operating plan for 2003. Both have been posted on the ICMM website (www.icmm.com). ICMM?s Operating Plan sets out three priority tasks: - Providing strategic leadership to achieve improved sustainable development performance in the mining, minerals and metals industry. - Contributing to international policy discussions on cross-cutting issues of importance to the industry, in collaboration with national and commodity associations. - Promoting dialogue and partnership with other organizations to catalyze sector?wide sustainability initiatives.

Jan 1, 2003

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train, the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71 percent — as confirmed by real operational data from the Antapaccay Mine in Peru. It was the first plant worldwide to use gearless drives for both applications.The gearless principleThe principal idea behind a gearless drive system is to reduce the number of components and diversity of parts, especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material.In order to apply this principle of simplification, the components of a conventional drive system are examined. They consist of:• Driven equipment (mill, conveyor, slurry pump).• Components altering the rated speed (gearboxes, girth gear/pinion).• The electric motor.• Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage.• Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation.• The electrical supply system (cables, switchgear, transformers, protection equipment)."

Jan 1, 2015

Well designed and maintained haul roads are the key to minimizing truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often difficult to achieve. Poorly designed and built roads exhibit high rolling resistance - a 1% increase in road rolling resistance can typically reduce speed on ramp by as much as 10% - and on the flat by up to 26%. In the current economic climate, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations ? simply by virtue of their contribution to overall cost of operations ? often in excess of 50% of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled ? is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road design is developed, and, critically, the interplay between a good design and safe, cost efficient haulage. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers? requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimize haulage hazards, both from a health and safety perspective. Whilst improved mine haul road design does indeed reduce haulage accidents, recognition also needs to be given to human factors which are a significant contributor to haulage accidents. The human factor is the most problematic to address in a road design. It is often easier break the link between the interactive effects which may lead to accidents than trying to predict and reduce human error. These human factor interactive effects include the geometric, structural and functional design components and to prevent an accident or reduce the severity of its consequences, a road should be more accommodating to human error. The more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By T. W. Camm

"As engineers, we are trained to use logical, rational problem solving to insure our mines operate at maximum efficiency. We tend to use the same technical approach to design safety into all mining systems. This works well for machines, but not so much for the human component. Recent insights in the field of behavioral economics provide useful ideas for addressing the fact that we are driven by emotions more often than by rational thought. Understanding the nonrational aspect of human behavior is an important piece of any safety system design. INTRODUCTION The most common economic model is based on humans making rational decisions; that given the proper information, we will make a logical, rational decision based on what is best for ourselves (Ariely, 2009, p. xviii). In many cases this is an accurate description of how we make decisions. As an engineer, I was trained to apply the precision of mathematics and logic to solve problems. As an engineering professor, I now teach this approach to bright young minds preparing them for a life of professional effectiveness as practicing engineers. That said, we are not only rational. Daniel Kahneman, winner of the Nobel Prize in Economics, describes a model for how we think (Kahneman, 2011). System 1 is the part of our mind that is fast, intuitive, and emotional; while our logical, slower, and deliberative mind is System 2. According to Kahneman’s model, System 1 runs automatically, most of what you think and do originates in System 1. System 2 takes over when things get difficult, including the application of math and logic, and the resolution (or avoidance) of conflict. As engineers, we would typically assume that we operate in System 2 mode most of the time. This is where the model becomes useful, for Kahneman points out two important aspects of the dynamic between the two systems in our mind. First, System 1 has biases, systematic errors that lead to answering questions with an easier answer (rather than a right answer) before System 2 is engaged. Second, we can be blind to the obvious, and also be blind to our blindness. Complicating things further, System 1 cannot be turned off (Kahneman, pp. 24-25)."

Jan 1, 2015