Search Documents

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By S. Kittel, P. Galleguillos, H. E. Urtubia

The rougher flotation at Escondida consists of 80 cells of 100 m3 each, with injected air. Escondida has developed a system of automatic control of the rougher flotation using video cameras, which have been operating since 1997 for remote monitoring and manual control. Since 1999, an image processing software and a group of rules have allowed implementation of an expert system. To date, the expert system controls the superficial speed of each cell by adjusting the air flow and the froth depth of the flotation bank. Preliminary tests of the expert control on two of the eight rows gave 1.2% higher rougher recovery at a 92% degree of confidence. The proven benefits are already sufficient to move towards a complete plant implementation.

Jan 1, 2001

By C. Green, J. Uhrie, C. Filippone, A. Guzman

A central aspect of heap leach management and recovery optimization is solution control. Insofar as each heap is unique in physical and metallurgical properties, it is essential to understand the hydraulic parameters that control the migration of solution on a case-by-case basis. Water Management Consultants, as part of an ongoing research effort for Phelps Dodge Process Technology Center, have adapted techniques of parameter estimation for application to data typically resulting from metallurgical column testing. The parameterization is completed within the context of a variably saturated flow model that allows interpretation of available hydraulic information collected during hydrometallurgical column tests. A novel interpretation approach is introduced to extract the necessary hydrodynamic parameters from typical hydrometallurgical data sets. Results from the application of the approach to standard metallurgical test data will be presented together with a discussion of the application of information gained to the design and operation of a heap.

Jan 1, 2002

By G. C. Presley

Estimated domestic production of pumice and pumicite in 2004 increased about 23 percent since 2003, according to the U. S. Geological Survey (USGS). The USGS estimate of domestic production of 687 kt(757,000 st) for 2003 turned out to be 870 kt (959,000 st)of actual production. The USGS estimated the value of pumice and pumicite sold or used in the United States to be $26 million in 2004, up $4 million from the value in 2003. There was an estimated decrease in the mine, or mill, average price to $24.14/t ($21.90/st) in 2004 from $25.19/t ($22.85/st) in2003.

Jan 1, 2005

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By Osvaldo Bascur, Barun Gorain, Jaco Steyn

"The last few decades have seen some remarkable advancement in information technology, but recently various digital technologies have resulted in several synergies to deliver innovation in diverse applications. The mining industry has been relatively slow in adopting these technologies compared to the other industries, but this scenario is changing fast.Challenges. Mining companies globally are going through a series of challenges such as declining ore grades with complex metallurgy, increasing depth of ore bodies, high capital and operating costs, lower productivity, shortage of technical resources, significant pressure from stake-holders to deliver, along with growing environmental and corporate social responsibility issues. Improvement in profitability would need significant improvements in operational performance.Consequently, over the last few years, there has been a major focus among some mining companies to imbibe operational excellence. This has been only possible because of the replacement of a silos-based approach by an integrated view of the organization. Such an integrated view is now possible via the evolving digital technologies. Even so, such a transformation calls for a change in culture, which, for most organizations is not trivial. Attempts in the past to integrate functions, such as through mine-to-mill initiatives in the mining industry, have demonstrated significant benefits to many operations (McKee, 2013). Still, sustaining these benefits has clearly been a challenge due to manpower turnover and lack of proper systems and structures that integrate information between business functions within an operation and between operations and the corporate level.Opportunities. The advent of digital technology has opened up opportunities to integrate interdepartmental information for a unified understanding across an entire organization. The advances in instrumentation, equipment control systems, supervisory control systems (SCADA/ Historian) and industrial networks have helped in the direction of enterprise- wide integration. The availability of real time information across an enterprise has given rise to numerous possibilities to improve organization performance. As suggested by Seshan and Gorain (2016), some of the potential opportunities are as follows:"

Jan 9, 2018

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By Timothy P. Smirnoff, Tracy K. Lundin

INTRODUCTION The City of Phoenix, Arizona is located in the Phoenix Basin watershed which is prone to flash flooding several times each year. The runoff from these storms moves from the mountains in the north to the Salt River in the south. An extension of Interstate Highway 10 (1-10) will pass through the city east to west to form an Inner Loop through the downtown business district. PROJECT DESCRIPTION The I-10 Inner Loop extension will be a depressed roadway which would intercept the surface drainage of the Phoenix Basin and separate the watershed into two regions. To prevent flooding of the depressed roadway, runoff storm water collected from the northern half of the drainage area will be conveyed beneath the roadway to its natural outlet at the Salt River. A conveyance system composed of pressure tunnels beneath the city, shown in Figure 1, was proposed to achieve this goal . Table A presents the prominent features of each of the tunnels. This paper will describe geologic and engineering parameters specific to Phoenix which were used in the design of a series of tunnels to convey storm water from the I-10 Inner Loop to the Salt River. The design of tunnel initial and final support is described along with support and construction methods used by the Contractor.

Jan 1, 1985

By J. Hebert, J. Donnelli, J. Sedey

Installation of a Load Commutated Inverter (LCI) provides an economical method for conversion of a Fixed Speed Semi-Autogenous Grinding Mill into one with variable speed, qualities. Though capital intensive, the conversion appears to be one of the most cost-effective methods to gain the advantage of critical speed variations for variable ore characteristics. Expected advantages from the installation of LCI drives at the Goldstrike Mine were decreased liner wear, decreased media consumption and additional grind for increased production rates. These issues as well as construction, economics and performance will be discussed in the presentation. The utilization of the existing equipment came to play an integral part of the study and economic justification of the overall project.

Jan 1, 1999

By Trevor Ellis

The following is extracted from a report by the author to the International Valuation Standards Committee (IVSC), with minor modifications for the purpose of publication. The author represented the IVSC at the annual session of the Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology. This is a body organized by the United Nations Economic Commission for Europe (UNECE). This second session, held in Geneva, Switzerland, achieved an important agreement for advancement toward uniform global standards for the classification of minerals and petroleum reserves and resources. Attendees discussed the possibility of enhancing the United Nations Framework Classification for Energy and Mineral Resources (UNFC) for implementation globally as the classification standard for use in financial reports under the International Financial Reporting Standards (IFRS). Presently, there are between 100 and 200 mineral and petroleum resource classification (or definition) systems throughout the world — a similar number to what there are countries.

Jan 1, 2006

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By W. Z. Rogers

U.S. feldspar output sold or used in 2005 was an estimated 760 kt (838,000 st), valued at $44 million free-on-board plant. This was below the 2004 volume and was the second year of decline in a row. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures and fiberglass insulation requiring feldspar. Shipments of glass containers were about the same as in 2004. Imports of ceramic tiles and plumbing fixtures continued to increase, taking the place of U.S.-produced goods and the feldspar required to make them. For 2005, 80 percent of the ceramic tiles sold and 50 percent of the plumbing fixtures sold in the United States were imported. Since 2000, manufacturing plant closures in the plumbing fixtures industry have reduced the demand for feldspar and feldspar-silica mixtures by 100 kt (110,000 st). Increased demand from the ceramic tile industry has partially offset the lost volume.

Jan 1, 2006

By F. L. Pirkle, W. C. Bagby

"In his 1989 book, The New Realities, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, Claremont, CA, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized” (p. 209).The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze and interpret data that are material to a mineral-valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral-valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality and transparency, the three pillars of mineral valuation (minerals valuation, mineral-property valuation).The International Mineral Valuation Standards Template (IMVAL Template), third edition dated May 2018, defines mineral valuation as: “The estimation of the value of a mineral property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the valuation conclusion) or to refer to the preparation of the estimated value (the act of valuing)” (p. 14).Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The template deals with valuation, which is distinct from evaluation. The distinction inherent in these defined terms is that valuation addresses the estimation of value of a mineral property, whereas evaluation addresses the broader assessment of a mineral property for an investment decision (p. 2).”This is an important difference because the minerals industry commonly makes investment decisions using feasibility studies to evaluate a proposed mineral development and production project. The purpose of such investment-decision analysis is distinctly different from valuation of a mineral property, no matter where that property lies upon the mineral explorationdevelopment- production-reclamation timeline (Fig. 1). Valuation involves terms such as market value, just compensation, fair value, etc., whereas investment-decision analysis is concerned with the economic viability of a given proposed project. Although feasibility analysis and market valuation can both use discounted cash flow (DCF) analysis as a tool, the formulation of the DCFs and their interpretation are different."

Nov 1, 2019

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

By A. Lashgari

Surface coal mining in the Appalachian region consumes a significant amount of energy in the form of diesel fuel and blasting agents. emission of oxides of nitrogen (Nox) from these sources represents an environmental challenge to the mining industry. this paper presents the results of research work related to determination of Nox emission of mining equipment and blasting agents, which is part of a broader industrial project conducted by the Appalachian research Initiative for environmental research (ArIeS). Data for this project are collected from an operating surface coal mine in West Virginia. the research work presented here may be used by mining professionals to aid in quantifying Nox emission and determine strategies for reducing its overall environmental impact.

Oct 1, 2013