Search Documents

By C. E. Jordan

The Bureau of Mines conducted research to determine the effect of fine bubbles on the flotation of fine-sized particles (minus 20-um size). Turbulent flow collision models for fine particles and fine bubbles were reviewed. Velocity distributions within the flotation cell along with measured bubble and particle size distributions were considered in the models to predict the flotation response. The models were corroborated with laboratory fine-bubble flotation tests to verify the expected increase in flotation efficiency.

Jan 1, 1988

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By M. Wason

An Ore bed magnetic liner element is made of permanent ceramic magnets embedded in a rubber molding. (See figure 1) They are difficult and expensive to manufacture correctly. Therefore, the lining for a complete mill is expensive, as high as 400% more than conventional rubber liners. The magnets are not very resistant to impact as they are very brittle. Mills of 12 feet or more can use only I inch balls; mills under 12 feet can use balls of 1-1/2 inches. These liners are therefore used in regrind applications with small balls or in secondary pebble mills. Rubber liners for these applications last a long time, so if life was the only consideration, the pay back for these liners would be longer than the life of the mine. The Ore bed liner and its bed of ball chips or magnetic ore is relatively thin and the surface of this bed has a high coefficient of friction. The liners are made so that opposing poles are situated next to each other and that the mill shell and the bed of ore or ball chips completes the magnetic circuit. (See figure 2) The combinations of these properties results in a very efficient liner. Due to the low profile of this bed, there is no material that is lifted too high, so we have a very compact charge with very high attrition, good for fine grinding. These liners have shown a 10% ball consumption reduction and a 10% lower power draw for the same capacity. Due to the magnetic orientation, the bed is formed in a wave shape along the lines of magnetic force. Tests conducted at a copper mine in the southwest United States have confirmed these findings. The mills where the liners were tested are 10.5 feet by 16 feet Hardinge regrind mills operating as overflow ball mills.

Jan 1, 1999

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By F. Heivilin

"Health and Safety problems can make a mineral deposit or a portion of one, an operating plant, or finished product unprofitable or worthless. Therefore they need to be reviewed when reserves are established and yearly thereafter until the deposit is closed down. Health and Safety regulations serve as a guide, but I have always done more frequent checks, when adding new products with different specifications or during times of bad weather and crisis. Water quality and quantity are always in question. Health and Safety are quality of life issues which are at or near the top of priorities for communities, companies, employees, and government bodies. Georgia dropped from one to three in U. S. for business development due to “Quality of Life” issues. Remember crystalline silica is present in nearly all sedimentary and acidic rocks and basic igneous rocks are the perceived home of asbestos. These health issues, any other safety and health issues or perceived issues need to be resolved initially and any time they come up during life of deposit. When handled properly good safety and health programs add to the profitability of a deposit, not to the costs. Daily safety checks in operating plants and mines, and visual check of all drilling core with an eye for changes are a key to successful programs. Both plants I turned around had terrible safety records, too much airborne dust, and maintenance problems resulting in low productivity. In almost every case cost reduction was tied to eliminating maintenance and spillage problems which caused health problems and increased possibility of accidents. Implementation of these safety and health programs around 1970 starting prior to government programs, working with new MSA/MSHA regulations, working to improve the regulations as a president of a state mining organization, and maintain profits was a challenge, but very rewarding. Reducing time to make repairs and work simplification gleaned from observations and employee recommendations learned from making multiple daily inspections resulted in years without lost time accidents at two plants, reduced maintenance and 33-75 % improvement in cost per ton at A. P. Green Refractories Co. Eufaula Calcining Plant 1972-77 and Oil-Dri Ochlocknee plant and mine 1979-82. The Ochlocknee mine worked 1981-2007 without a LTA. The author participated in 16 acquisitions and new plant design projects. All of above reduced costs allowed mining deposits with higher overburden to be used and considered. Thereby increasing reserves considered in all operations."

Jan 1, 2016

By R. O. Y. Breese

The term "diatomite" implies the nearly pure sedimentary accumulation of diatoms. Sedimentary and chemical purity, low density, inertness, intricate fine structure, high brightness and other properties give the diatom and diatomite unique industrial usefulness and commercial value in high value functional filler and specialty filter aid products. Although diatomite deposits occur commonly throughout the world in Miocene and younger marine and lacustrine sediments, deposits that contain significant reserves of crude suitable for these quality sensitive markets are uncommon. U.S. production is centered on exceptional deposits located in Arizona, Nevada, Oregon, Washington and California. Evaluation of deposits requires understanding of geology, mining, production and end use. As crude quality in deposits varies within and between strata, ore suitable for quality sensitive end uses must be identified through sampling and evaluation programs tailored to permit recognition of critical variations.

Jan 1, 1989

By R. K. Singhal

The underground coal mining systems have kept pace with the developments that have occurred in other types of mining industry. A diversified group of machines with high horsepower motors, built-in microprocessor technology and with numerous options to satisfy the miners need in a varying geological environment are now available. A brief review of this existing technology and its likely status within the next 21 years is presented. Discussed also are some of the on-going advanced developments in electronic mechanization, remote control and automation together with mine wide data monitoring and management systems and facilities to process and transmit data to remote computerized stations.

Jan 1, 1989

By R. Torbin

The degree to Which automation/remote control/robotics has been utilized in the mining industry is far less compared to general industry because of several factors. These factors include the adverse working environment, the difficult work operations, and the generally lower incentive for capital investments in new mining equipment. Foster-Killer has been actively involved in the development of advanced mining and underground construction equipment. This equipment is designed to be remotely operated to improve both productivity and worker safety. Many of these machines employ advanced electronics and robotic features. Other types of Foster-Miller developed robots will also be described Which could be applied to special mining problems. The types of machines that will be discussed include the following: remote shaft lining/placement. remote excavation/mining operations, automated conveyor system, and robotic surveillance.

Jan 1, 1989

By A. G. Mayton

Bureau of Mines research has addressed improved operator protection for thin-seam shuttle cars. Because of working height restrictions in thin-seam mines (1.22 m or 48 in), MSHA regulations require that-canopy protection on shuttle cars be provided only in mines 1.07 m (42 in) and greater; however, variances are given to mines 1.22 m (48 in) and below. This paper reviews past Bureau efforts to develop protective structures for thin-seam shuttle car operators. The paper also discusses recent research leading to a novel method of protecting shuttle car operators, in mines as low as 1.02 m (40 in), through the use of a cross-car, end-mounted operator compartment.

Jan 1, 1989

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem.

Jan 1, 1989

By Steve Rogers

Nautilus Minerals was listed on the Toronto Stock Exchange in May 2006. The company now has major mining companies Anglo America (5.7%), Teck Cominco (7.2%) and Epion Holdings (22.4%) as significant shareholders, and has raised approximately $US346 million dollars to develop the world's first deep-water mine. The company is currently targeting high-grade copper and gold in seafloor massive sulphide mineralization, located near plate boundaries in back-arch basins of the Western Pacific. The first mine scheduled to be developed by the company is located in 1,600 meters of water at Solwara 1, in the relatively quite waters of the Bismarck Sea approximately 50 km from the port of Rabaul, within the Territorial Waters of Papua New Guinea. During 2006 and 2007 the company completed detailed environmental and geological studies, culminating in a number of world firsts, including the world?s first NI 43-101 compliant resource statement and environmental impact study for a seafloor massive sulphide system. Permitting is well advanced for the project, with initial production scheduled for late 2010, subject to timely grant of the permits. Extensive government and stakeholder liaison and engagement has been undertaken throughout the projects life, and is a core feature of Nautilus' desire to "do it right" in all aspects of this new industry.

Jan 1, 2008

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By R. T. Leigh

The continued decline In the production of synthetic soda ash (sodium carbonate) due to high costs and associated environmental factors, has improved the world demand for natural soda ash. The largest resource of natural soda ash is the mineable trona deposits of Southwestern Wyoming. Wyoming trona, a lacustrine evaporite of Eocene Age, is mined by five producers which process over 90% of the United States and 20% of the worlds soda ash. Total world consumption of soda ash is forecast to grow 1% annually. Increased expansion into foreign market's is absorbing the domestic overcapacity.

Jan 1, 1989

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

By Martha S. J. Leary, Malcolm J. McPhersqn

This paper introduces a computer simulation which extends the utilization of microcomputer systems for mine ventilation planning. The program was developed as part of an ongoing study to produce a simulation model that would determine the optimum duties of a main fan and a booster fan without requiring the trial and error runs that are necessary with currently available programs. To use the new program, the user specifies the location of one main fan and one booster fan, and the minimum required airflows in any number of working places. The computer deter-mines the fan duties that will maintain the required airflows at the lowest operating costs without causing undesired recirculation. The methodology of the program and an example showing how it can be applied are presented.

Jan 1, 1988

By F. A. Renninger

Limestone and dolomite are the most common rock types mined and quarried as industrial minerals in the United States. In 1993 over 720 million tons of limestone and dolomite valued at over 3.1 billion dollars were extracted and consumed throughout the nation. While the greatest volume of this vast production is used as aggregate for construction purposes, few people realize how critical limestone and dolomite are to our food chain and our national goals of clean air and water. Limestone, including dolomite, can truly be called nature's gift to the environment. Without a reliable, economical source of limestone the quality of our environment would be severely comprised and the standard of living of our citizens dramatically reduced.

Jan 1, 1995

By Dean J. Acuff

An overview of new size reduction technology involving the use of two-mass natural frequency vibration applied to a totally enclosed elongated drum. Material moves with a drum-like rotary motion with exposure to constant, aggressive, high frequency agitation for faster reduction and enhanced product quality. A proven, patented design with few moving parts, a vibrating mill drum provides the desirable environmental benefits of a totally enclosed rotary drum but without the same interfacing difficulties. Natural frequency design has reduced energy demand which is met by low horsepower, self-contained, motorized drives to dramatically reduce the cost per ton of finished product.

Jan 1, 1993

By D. S. Dick

Over the last few years, new methods to characterize the flow properties of bulk solids have been developed. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field conditions. In addition, the effect of large particles on a material's flow properties (cohesive strength, bulk density, wall friction) can be determined as well as the effects of various additives such as Freeze Conditioning Agents. New developments have also taken place in terms of devices to improve the reliability of solids flow. Much attention has been paid to finding ways to provide a mass flow pattern with relatively shallow hopper walls through the use of inserts. Such devices can also provide reliable in-bin gravity blending of bulk solids and/or completely non-segregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. Many of these developments have direct application in the mining and minerals processing industries. Examples of each will be highlighted.

Jan 1, 1988