Search Documents

By Kelly F. Bailey

Introduction On June 20, 1986, the Occupational Safety and Health Administration (OSHA) published revised asbestos exposure standards for general industry and construction. The standards reflect OSHA's attempt to adequately control workplace exposures to minerals it considers carcinogenic - minerals capable of causing or contributing to cancer. These standards specifically identify asbestos as: chrysotile, an asbestiform serpentine mineral; and the amphibole minerals amosite, crocidolite, tremolite asbestos, actinolite asbestos, and anthophyllite asbestos. Each of these has a more common nonasbestos mineral analog that exists in nature in a crystalline, blocky shape rather than the hair-like or fibrous shape of asbestos. The mineralogical names for three of these nonasbestos minerals are unique: antigorite for chrysotile, cummingtonite-grunerite for amosite, and riebeckite for crocidolite. The other three nonasbestos analogs do not have unique mineralogical names. They are simply designated as actinolite, tremolite, and anthophyllite without the word asbestos following their names. The 1986 OSHA standards not only cover exposure to the six asbestos minerals, they also cover specifically the nonasbestos forms of actinolite, tremolite, and anthophyllite (AT&A). The new standards regulate these minerals exactly like asbestos (OSHA, 1986). The construction aggregate industry views this as a major problem because these nonasbestos minerals are common amphibole rock-forming minerals in the earth's crust. They exist in small quantities over large areas of the United States (Kuryvial et al., 1974). These minerals, unlike asbestos, are not mined for a specific commercial purpose. They are unavoidable components in much of the aggregate used for construction throughout the US. They are also common in the gangue material of metallic ores. There are areas of the US where amphibole-bearing bed¬rock is common. Not every rock mass in these areas contain amphiboles, however. It does mean, though, that amphiboles are physically compatible with many of the rocks in those areas. And given the correct geochemical conditions, they will be present primarily in the nonasbestiform variety. In addition, these amphiboles will probably exist in the natural drainage system, sand and gravel deposits, stream sediments, lake shores, valley basins, or ordinary beach sand within these areas. There has been little quantification of nonasbestiform AT&A in dusts and soils in the US. This is not surprising since these nonasbestiform minerals are not commercially valuable. However, an example of the pervasive nature of these minerals can be found in a 1981 Geological Society of America publication where about 0.7% tremolite-actinolite was found in the desert dust in and around Tempe, AZ (Pewe, 1981). Since OSHA standards treat these common nonasbestos minerals as carcinogens in the same way as asbestos, large natural areas in the US are implicitly being labeled as hazardous by OSHA. When a substance is identified as a carcinogen, another OSHA standard comes into play, the Hazard Communication standard. There are also right-to-know laws in 9 states that essentially duplicate this federal standard. These standards require that a product containing 0.1% or more of an OSHA-designated carcinogen be labeled as such (OSHA, 1983). This means that much of the stone and sand gravel products occurring naturally and mined in the US could be labeled a carcinogen when, in fact, they are not. The National Stone Association (NSA) and the domestic construction and mining industries believe that OSHA has seriously erred. The NSA has studied the health, mineralogical, technical, economic, and legal basis for OSHA's action. These studies concluded that there is no justification for the agency regulating nonasbestos minerals as if they were asbestos. Health issues The preamble to OSHA's 1986 asbestos standard states that evidence for asbestos-like health effects from exposure to nonasbestiform varieties of AT&A is inconclusive (OSHA, 1986). The fact is, not only are the data inconclusive, they are nonexistent. During 1986-1987, NSA's occupational health and epidemiology consultant, Environmental Health Associates (EHA), reviewed all available health studies related to AT&A. EHA found evidence that malignancies in both experimental animals and humans are associated with the asbestos forms of these minerals. No experimental or epidemiological evidence was found that indicated such pathogenic effects occur from exposure to nonasbestiform varieties of these minerals. There are relatively few scientific studies of the health effects of exposure to nonasbestiform varieties of AT&A. In three different animal studies, exposure to either nonasbestiform tremolite or actinolite did not result in pulmonary fibrosis on in excess tu-

Jan 11, 1988

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990

By W. J. Douglas

Before discussing minicomputer software for the mineral industry, it is helpful to explain some of the computer program terminology. Most of the terms are the same as those applied to large computers. A computer system consists of a machine (hardware) with electronic and mechanical components and instructions (software) that define its operational logic and sequence. This logic is described by sets of commands grouped into programs. Each program has specific objectives related to the computer's operation and to production information from computer data that are input and processed. Software, therefore, is a general term applied to any type of computer program. Instructions to the computer are communicated through languages that convert logical and arithmetic statements into machine operations. The languages may consist of statements resembling mathematical or logical phrases understandable by humans, or they may be coded statements with no apparent resemblance to spoken language but readily understandable by the computer. Computers also translate higher level languages such as FORTRAN or COBOL into machine languages using other programs called Compilers. Programs written in these higher level languages are generally called source code. However, programs written in computer assembly language may also be called source code. The compiled version of the program after it has been translated by the compiler software is called object code. Programs used to "instruct computers how to be computers" are generally called systems software. They relate more to computer operation than to producing externally usable results. Programs producing information for many users-engineers, accountants, managers-are termed applications software. For the most part, applications software is the principal concern of the mineral industry. Programs are developed to fit user requirements as interpreted by programmers. Programs vary in quality, precision, efficiency, accuracy, and complexity, depending on programmer skills and abilities and programming decisions forcing design tradeoffs. A well written program should have speed, efficient use of available hardware resources, accuracy, and an inherently logical structure that aids documentation and subsequent modifications. Programs developed to fit specific requirements are termed customized software. A program organized and prepared for general commercial use is called a package, or a software package, and includes documentation for program use. A form of customized software that takes an existing program or package as its starting point and modifies it is called a customized package. A minicomputer program can be stored on computer cards, standard magnetic tape, magnetic cassette tape, floppy disk, or hard disk. The software purchaser or lessee may select one or more of these media when specifying a program in a software contract. Supporting documentation may include a listing of the program instructions linkages, hardware and storage resource requiremnents, flow charts, and programmer and user manuals. The purchaser must carefully make and clearly understand specifications for media and format of program delivery. This assures that delivered software is compatible with the intended hardware. Mineral Industry Attitudes Toward Computer Software The mining industry has traditionally been conservative concerning computer applications. Furthermore, large computer costs have made these systems accessible only to large companies, for the most part. But in the past few years, mining software systems developed at schools such as Pennsylvania State University and Virginia Polytechnic Institute have gained wider acceptance in the mineral industry. More mining engineers now have academic training in computer application, and computer use is now more acceptable to the mining industry. Mining managers in decisionmaking positions are faced with a new generation of computer technology resulting from the rapid evolution of minicomputers. Not too long ago, manufacturers such as Digital Equipment Corp., Data General, and Hewlett-Packard were considered newcomers. They are now established companies. In addition, Apple, Radio Shack, Commodore, and others have emerged in the growing microcomputer industry. So the mine manager or mining executive now has more options. Mining Software is Limited Along with the rapid evolution in hardware development, much general purpose software is now being developed for minicomputers. The 1981 Apple Software Directory can be obtained for about $14; Radio Shack published the Application Software Source Book in three volumes for $1.95 each. Brochures describing software can be obtained for other minicomputer manufacturers by contacting local sales representatives. Hewlett-Packard software can be obtained and exchanged through HP user's groups. Manufacturers' programming staffs are generally concerned with developing applications software. In some instances, manufacturers will recommend software developed by their hardware users. Until now, however, software development for mining applications has been minimal. This should not be surprising, since software development traditionally lags hardware development by several years. A review of A Directory of Computer Software Applications/Mini-Computers and Micro-Computers, August 1977-1980, published by the US Department of Congress, National Technical Information Service, contains many entries and subject areas. General applications include some references to tunneling machines, but there are virtually no entries specifically relating to

Jan 11, 1981

By Geoff W. Seward, Charles J. Maes

INTRODUCTION The work of the metallurgical engineer engaged in developing a leach, solvent extraction electro- winning process usually begins in the laboratory and generally proceeds via pilot plant testing before finally resulting in a commercial operation. The path leading to the development of the eventual process will involve a test program on leaching in order to derive information on the amenability of the copper-bearing material to acid dissolution, under various conditions. Commonly in North America the leach process of choice is either dump or heap leaching but it may also be in-situ leaching or the treatment of mine waste- waters and bleed streams. In the past, agitation and vat leaching have also been included in the list of options. Currently the economics of copper production dictate that only material of mineralogy and grade, capable of being leached without prior milling, will lead to a viable process. This is not necessarily true in other parts of the world where grades are higher and milling costs lower and therefore this paper con- fronts all the techniques available to the metallurgical engineer in terms of the evaluation of the solvent extraction process. Understanding the objectives of a laboratory and pilot plant evaluation of a solvent extraction route is important and these are described in some detail in this paper. Of at least equal importance is understanding limitations of such a test program and this aspect of process development is also discussed with reference to the kind of equipment and experimental practices that have been shown to produce results consistent with the objectives. WHERE TO BEGIN? At the inception of a project much information is developed on the variables of the leach process and indeed in some instances the type of leach that best suits the ore to be treated is the subject of intense investigation (Wadsworth 1983). The decision to treat the leach solution by solvent extraction focuses attention on the selection of the extractant most suited to the nature of the chemical composition of the solution. A laboratory screening program will probably need to be arranged in order to assist in narrowing the options and the following is suggested for this initial screening. Selection of a Representative Leach Solution This is preferably obtained from leaching a representative sample of the ore under conditions likely to pertain in the commercial leach circuit. As the conceptualized circuit flow sheet will undoubtedly involve the recycle of aqueous solutions via the leach, then it is desirable to know the nature of and the likely level of the impurity ions in the solution as well as the concentration of copper. The other most important parameter that is required is the free acid (Anon, Acorga Analytical Method) content of the solution. As a rule of thumb, it is always true that recovery across SX is maximized as the pH of the leach solution rises. Whilst a high pH may be desirable for SX recovery, it is not always desirable for the pH (or more correctly, the free acid) of the leach to rise too high. The working range, therefore, tends to be between 1.5-2.5 pH. At an early stage in process development it is likely that a number of ill-defined conditions will exist, making it difficult to decide on typical leach conditions in which case the screening tests should be carried out using a synthetic leach solution prepared from laboratory chemicals. In doing this the copper and free content should be carefully controlled along with the appropriate addition of major impurity ions as their sulphate salts. Preparation of Suitable Organic Solutions Manufacturers information sheets on the reagents to be tested are required at this stage The information necessary to make an informed judgment on reagent performance is: Copper Uptake Value. This will indicate the amount of copper that can be extracted by a reagent as a function of its operating concentration in a

Jan 1, 1986

By Feng Cai

"As a new method to support gate roadways, rock bolting has been widely used in the big coal enterprises for its superiority. The disturbed stress field of surrounding rock and anchor pre-stress field were divided into 3 areas in consideration of s1, s3. The surrounding rock failure form and characteristic were analyzed in combination with parameter f, the failure mechanism was explained using the slip line theory, furthermore, the rock bolting mechanism and its arrangement were studied. After roadway excavation, the tensile stress area appeared at the surface of the surrounding rock. The failure type changes from shallow tension-shear form into deep compression-shear form and the failure shape is an “incense burner”, surrounding by high risk failure area in butterfly shape. The maximum principle stress in roof appears discontinuous distribution because of layers separation. The failure type of surrounding rock is intensity-stress environment-weak plane control model. The internal reason of roadway macroscopic failure is the displacement between the surface plastic area and the deep elastic region along the tangential direction of slip line. In condition of rock bolt support, there is one-way tensile stress area in small range at the surface of surrounding rock, inside is the bidirectional compressive zone in uniform distribution form, stress environment is improved by the superposition of anchor pre-stress and disturbed stress field, anchor rock bolt arrangement and pre-tightening force distribution is decided according to the distribution of f parameter. Finally, supporting method and parameter reasonability was proved by the roadway deformation monitoring, damage depth drilling peep test in the 8101 transportation roadway in a mine.Introduction The stability of roadway support is very important to the safety and sustainable development of coal mine. In recent years, the focus of China's coal mining industry began to move to West China, the thick-extra thick coal seam is developed in the West. The latest technology and equipment have been put in to service, the occurrence condition of thick coal seam and the increasing of productivity lead to the cross section of the roadway increasing continually, hence, it is more difficult to control the surrounding rock. At present, the most common way to support the roadway is rock bolt (cable) support (Wang 2007); Scholars have been deeply studied on the mechanism of rock bolt. It is reported (Wang et al 2012, Gao 2007, Zhang and Yuan 2006) that the influence of rock bolt on physical and mechanical parameters of coal and rock mass in the anchorage zone, It is believed that the rock bolt can improve the peak strength of surrounding rock, especially the post peak strength, and the failure mode of rock mass under the rock bolt support is analyzed. It is reported (Wang et al 2014, Xiao et al 2013, Li et al 2007, Yan et al 2012), according to different geological conditions, the failure mechanism of surrounding rock and supporting technology of the whole coal roadway were studied. Focus on the failure mechanism of roadway surrounding rock, different forms of high strength support methods were proposed, which achieved good results. It is reported (Wang et al 2012a, Zhang et al 2011, Wang et al 2012b, Kang et al 2010, Zhang et al 2010, Kang et al 2007) that the supporting mechanism of pre-stressed anchor was analyzed from the point of the distribution of the maximum principal stress in the pre-stressed anchor field, and the influence of the rock bolt support parameters and surrounding rock characteristics on the supporting effects were studied. Based on the latest research results, this paper analyzed the failure mechanism of surrounding rock of coal roadway, proposed the high strength anchor net cable combined supporting technology based on the feature of stress zoning distribution of surrounding rock, to provide reference for the coal roadway rock bolt (cable) support technology."

Jan 1, 2017

By H. Lyn Bourne

This is the sixth annual tabulation that gives mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data plus more than 100 new entries. In addition to the royalty information, some entries show the cost of purchased reserves. An article in the December 1984 Kentucky Coal Journal could have far reaching applications. It explains that a banking firm examined the "reserve risk" as one of six factors for analysis when financing a coal project. The firm concluded that coal reserves in Kentucky are worth an average of $0.29/t ($0.26 per st) in-place. The banking firm based this in-place value on its examination of more than 50 leases. In-place value is especially important when trying to establish a mineral value for a given deposit. Ernie Lehman wrote to this author after last year's column appeared and he quoted the lease rates for lead and zinc on federal land. He states, from first hand information, that the leases are based on a percentage of net smelter return as follows: 4% for the first five years, 4.5% for the next five years, and 5% thereafter. The figures used in last year's column ($ per st) came from dividing reported royalty income by reported production. The information reported last year merely translates the results of the net smelter return (as written in the lease) to royalty income per ton to the US Government for the various years. Statistics from the Minerals Management Service of the Federal Government show that oil and gas account for 40% and 53%, respectively, of the Federal royalty income. Coal accounts for about 4% and all other minerals, the remaining 3%. Oil and gas leases are mostly at 12.5%. Most of the coal leases are at 12.5% for surface mining operations and 8% for underground mining. Many of the other commodities are leased at 5%, which has been true for decades. Relative to Federal leases, this year's table shows some percentages and some costs per ton. This was done to give information about the leases and also to show income produced by various commodities. Note that some commodities have a variation in $/ton even though the royalty percent is the same. These variations result from a combination of factors that influence the value of a mineral commodity. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation (especially significant for most industrial minerals); • market conditions both for the commodity and the company acquiring the right to mine it; *quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give the location - either by state, US geographic area or Canadian province; the cost - R for royalty and P for purchased cost; and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cu ft), tons (/T, 2000 lbs) or acres (/A). 1 cu yd = 0.7646 m3 1 cu ft = 0.2832 m3 1st=0.9078t 1 acre = 0.4047 hm or m2 In several cases, the royalty is a percentage of the sales price of the finished product and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: G. Anderson, B. Brown, R. Ganis, K. Hauser, E. Lehman, and S. Sims. Their help is appreciated as are the contributions by those who asked to remain anonymous. This column requires additional information each year. That data must come from people in the minerals industry who have royalty information. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write the author at the address given in the author's box or call 313-462-0005.

Jan 7, 1988

By Franklin J. Stermole

The current financial state of the mineral industry, in general, is bad. Economic prospects for improvements in the near future are uncertain. What will improve mineral investment economics so the mining industry can return to a more normal (in terms of past experience) production level? Basically, mineral commodity prices must rise. They must rise to economically justify reopening closed mines and for management to seriously consider expansion or development of existing and new mines. With the worldwide economy depressed for more than a year now (longer for most segments of the mineral industry), supply/demand relationships for mineral commodities are such that prices are depressed-except for precious metals. In investment analysis of the economic potential of existing or new investments in any industry, product price generally is one of the key parameters having great impact on the economic viability of projects. Petroleum and synfuels industry development contracted last year for the same product price reasons that have brought mineral industry development to a standstill. Much of the new mine development activity now underway or in the serious planning stages around the world involves precious metals ore body development simply because precious metal prices are high enough now or are projected to be high enough in future production years to give overall satisfactory project economics. It will take significant improvement in nonprecious metal mineral commodity prices in 1983 to develop significant new mine investment interest except in very high grade ore body special situations. Mineral Investment Decision Making Before progressing further with the discussion of mineral investment considerations for the coming year, it should be emphasized that mineral investment decision making-like all industry or individual investment decision making does not relate just to economic considerations. Investment decision making should and generally does involve three analyses: • Economic analysis • Financial analysis • Intangible analysis Economic analysis evaluates the relative economic merits of investment situations from a profitability viewpoint based on discounted cash flow analysis of projected investment revenues and costs. Financial analysis, on the other hand, refers to where and how the funds for proposed investments will be obtained. Regardless of the project's economic potential, if you can't finance it, the project will not be done. Intangible analysis considers factors affecting investments but which cannot be quantified easily in economic terms. Typical intangible factors are legal considerations, public opinion, goodwill, environmental and ecological impacts, and regulatory or political considerations, to name a few. New mine development investment decision making in the US has been impacted heavily by intangible considerations in the past decade and will probably continue to be impacted by them in 1983. There is a common tendency in literature and management practice to interchange the terms economic analysis and financial analysis. This often leads to confusion about the rationale for investment decisions. For example, in the past year a majority of companies in all types of industries cut back budgets for new projects. Often this was done not because new project economics were unsatisfactory, but because cash flow from existing operations was reduced compared to previous years due to the recession, and debt service requirements were high from existing loans so new borrowing was undesirable. For financial reasons, in other words, many projects were shelved last year. That included some precious metal mining projects and many petroleum projects. Many other projects were shelved for economic reasons (sometimes combined with financial reasons in the case of marginal economic projects). New mine development for copper, lead, zinc, molybdenum, iron ore, and synthetic fuels are a few examples. Economic Uncertainty and Financial Considerations Mineral project analysis has always involved a lot of uncertainty with respect to determining ore grades, tonnage of producible reserves, operating and capital cost projects, and mineral commodity prices estimates. The wide swings in mineral commodity prices in recent years and the almost impossible task of projecting future prices with any degree of confidence or accuracy concerns mineral project investment decision makers. In developing a new copper or silver mine, it is not today's price of copper or silver that is relevant to economic analysis of the mine, but what the price will be during the producing years. There is no way to avoid projecting the escalation (or de-escalation) effects on revenues and costs. To analyze a project in terms of today's dollar revenues and costs implicitly assumes that escalation will not change today's project costs and revenues; or that, if they do change, the project economics will be unaffected by the changes. This often is not the best or even a realistic assumption. The inherent uncertainty associated with historical mineral price swings is exacerbated in 1983 by the uncertainty of when

Jan 2, 1983

By D. Akers, R. Dospoy

Introduction The geological processes that form coal can also concentrate trace elements in the coal. For example, the average concentration of arsenic in bituminous coal (20 ppm) is ten times the average concentration found in all the other rocks that make up the earth's crust (2 ppm). Similarly, other elements, such as antimony, cadmium, mercury and selenium, are more concentrated in coal than in the earth's crust. When coal is burned, trace elements can be further concentrated. Although no new constraints on trace clement emissions were placed on the power generation industry under the 1990 Clean Air Act Amendments, the act does mandate a three-year study of air toxics. Any new regulations aimed at electric utilities as a result of this Federally-mandated study will almost assuredly be very costly-an estimated $1 billion per year. Many trace elements in coal are associated with mineral matter. For example, arsenic is commonly associated with pyrite, cadmium with sphalerite, chromium with clay minerals, mercury with pyrite and cinnabar, nickel with millerite, pyrite and other sulfides, and selenium with lead selenide, pyrite and other sulfides (Finkelman, 1980). There are also cases in which some of these elements are organically bound. Just as both organic and pyritic sulfur can be found in the same coal, the same trace element may be both organically bound and present as part of a mineral in the sane coal. Physical coal cleaning techniques are effective in removing mineral matter from coal and can potentially remove at least some of the trace elements associated with specific minerals, thereby reducing the release of these elements into the atmosphere. Conventional coal cleaning to remove trace elements As part of a project funded by the Electric Power Research Institute, CQ Inc., a wholly-owned EPRI subsidiary located in western Pennsylvania, has demonstrated that large reductions in the concentration of many trace elements are possible if conventional coal cleaning techniques are properly applied. Four examples are given in Tables 1 to 4. In each example, the results shown were generated by cleaning the coal at CQ Inc.'s commercial-scale cleaning test facility. Cleaning results for Upper Freeport Seam coal from Northern Appalachia are provided in Table 1. Data are presented in the table in two ways: as a weight-based concentration (parts per million) and as a concentration per heat unit (grams per billion Btu). Grams per billion Btu is analogous to pounds per million Btu, but avoids the use of numbers with many decimal places. The heat-based concentration provides a better measure of boiler impacts, because the increased heating value obtained through coal cleaning reduces the number of tons that must be burned to produce a given thermal output. Reducing the quantity of coal burned reduces the quantity of trace elements entering the boiler. This raw coal is relatively high in several trace elements of environmental concern, including arsenic, cadmium and chromium. Cleaning provided large reductions in the quantity of arsenic, barium, cadmium, chromium, fluorine, lead, mercury, nickel, silver and zinc. The results for tests with a Powder River Basin coal, Rosebud/McKay, are presented in Table 2. Large reductions in arsenic, barium, cadmium, fluorine, mercury, nickel, selenium and zinc were observed with cleaning. The concentration of chromium increased with cleaning, while lead concentration increased in one test and decreased in another. Table 3 presents test results for Croweburg Seam coal from Oklahoma. Large reductions in arsenic, barium, cadmium, chromium and zinc were obtained with cleaning. Smaller reductions were obtained with lead and nickel, while chromium, fluorine and mercury increased in at least one of the tests. Table 4 presents cleaning test data for Kentucky No.11 Seam coal. In this case, large reductions were obtained with all elements measured. In general, these data indicate that physical coal cleaning is effective in reducing the concentration of many trace elements, especially if they are present in the coal at relatively high concentrations. The degree of reduction achieved is coal-specific, relating in part to the degree of mineral association of the specific trace element and the degree of liberation of the trace element-bearing mineral. The extent of trace element removal also depends on the method of cleaning the coal. Figure 1 is a washability plot, by size fraction, of arsenic vs. ash content for Upper Freeport

Jan 1, 1994

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By Thomas J. DeMull

Amax Gold's Sleeper Mine was brought to production as an open pit mining, cyanidation milling operation in March 1986. The Sleeper deposit is unique in that it contains zones of very high grade gold ore. Despite blending of ore, mill head grades have varied over a broad range. These grade variations were anticipated during mill design and affected, in particular, the sizing and selection of equipment for the CIP circuit. When grades proved to be even higher than anticipated, design operating parameters were adjusted shortly after start-up to accommodate the higher grades. Operating results have been excellent: during the first 18 months of operations the Sleeper mill has processed 375,600 tons of ore and produced 229,000 ounces of gold.

Jan 1, 1998

By H. O. Seigel, John C. Robbins

Luminex is a new method of prospecting for mineral deposits based on time-resolved mineral luminescence created by an ultra-violet light source. Developed by Scintrex Ltd., Luminex detects and resolves a group of key minerals - either ore minerals themselves or, more often, accessory or pathfinder minerals for certain types of economic ore deposits. These minerals are commonly found on the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits that are remotely detectable from the air. Tungsten, tin, molybdenum, gold, and bedded lead-zinc deposits are included. Therefore, Luminex is a natural supplement to the three classical methods of airborne geophysics. The luminescence of minerals has been known and used qualitatively in mineral exploration for many years. But there are more than 500 minerals known to be at least sometimes luminescent. Luminescence of most is unpredictable and the colors they emit may vary from locale to locale. It is, perhaps, this apparent complexity of the field that has discouraged its proper scientific scale until now. There are two basic types of luminescent minerals - intrinsic and impurity activated. In the first type, luminescence is an inherent property of the mineral in its purest form. In the latter, luminescence is due to the introduction of foreign trace elements, often in very modest amounts (ppm), into the crystal lattice. These trace elements are known as activators. There are very few intrinsic luminescent minerals commonly found in nature. Chief among these are the calcium tungstatemolybdate family, more commonly known as the scheelite-powellite family, and the uranyl minerals such as autunite and saleeite. The vast majority of other known fluorescent minerals such as fluorite, hydrozincite, and many calcites, are impurity activated - that is, they will not fluoresce in purest form. In addition to the many minerals likely to luminesce at the earth's surface under ultraviolet excitation, any prospector who has ventured out at night with a mercury lamp will know that much organic matter luminesces - for example lichens and even scorpions. Just as the eye finds difficulty in resolving the luminescence of minerals from that of organic materials, it also has its limitations at sorting out minerals from one another by their luminescent colors. Figure 1 shows, in part, the photoluminescent emission spectra of scheelite, hydrozincite, and autunite. It is clear that there is a considerable similarity in spectrum between scheelite and hydrozincite and a great deal of overlap. In fact, a small amount of molybdenum in the scheelite lattice can almost bring these two spectra into coincidence. On the other hand, the autunite emission spectrum is clearly resolved from the other two. Basis of the Method The right-hand side of Fig. 1 shows the time waveforms of decay of the photoluminescence of the same three minerals. It is apparent that the lifetimes of photoluminescence of scheelite and hydrozincite are radically different and that these two minerals, therefore, may be readily resolved through their emission lifetime characteristics. It is in the realm of time-resolved measurements (lifetime characteristics) that Scintrex has made its major advance in the Luminex method. With the exception of some work by Exxon confined to uranyl minerals, to the best of our knowledge, no systematic scientific investigation has been carried out in the field of time-resolved mineral luminescence studies other than the work of Scintrex. Scintrex's findings are that all organic materials and most commonly activated luminescent minerals have lifetimes shorter than one microsecond. In addition, only a relatively small number of minerals - among them those called key minerals, or certain ore and pathfinder minerals - have lifetimes greater than one micro-second. Scintrex is able to characterize these minerals primarily by their emission lifetimes and secondarily by their emission spectral characteristics. By a combination of these factors a mineral index is arrived at. From that, photoluminescent minerals can be resolved from one another with a high degree of probability. At least two spectral channels and two time channels - of which one can be common - are required to apply this mineral index. Ground System A portable hand-held Luminex analyzer based on a modulated mercury lamp has been used to date in Canada, the US, and Australia. The current production model of this device is the LG-2. It has two spectral channels and two time channels for each spectral channel. Figure 2 shows a ground Luminex traverse over the Texas-Arizona zinc prospect in Arizona. The instrument was set so the channel read was hydrozincite-specific insofar as possible. The mineralization in this prospect is known to be hydrozincite and other zinc secondary minerals in limestone. Figure 3 shows a ground Luminex traverse over the AAA uranium prospect in Nevada. The instrument was set to optimize the uranyl response. For comparative purposes, broadband scintillation counter readings were made on the same stations (also shown in Fig. 3). It is apparent that both the Luminex and the scintillation counter results reflect a near-surface distribution of uranyl minerals. It is interesting that no visible uranyl secondary minerals

Jan 7, 1983

By John J. Gillis

There is an ongoing battle to gain general acceptance of fossil fuel byproducts as safe, economical and useful agro-industrial materials. Despite that, the US ash industry is witnessing a steady growth in the volume of coal burned, along with the production of greatly refined, higher-quality ash particulates. There are two principal reasons for this. Economics have caused an increasing number of US electric utilities to convert from oil-burning to coal-burning. And the Federal government has tightened specifications on fly/bottom ash production quality. Hence, it must be noted that new and more stringent Federal regulations were implemented in 1980. The resultant ash particulates are finer, more compact, and less heavy than in previous years. Additionally, the first shift from oil to coal in the US was initiated in December, 1979 by the New England Power Co. in Massachusetts. Coal is the most widely-distributed fuel in the US. And it is found in 38 states. The wide availability of this fossil fuel and its general cost-efficiency, coupled with the undaunted move of US electric utilities toward nuclear power, are major factors affecting the current statistics on ash generation (65.4 x 106 million tons). Interest in the use of coal in power plants is creating a unique ash disposal and use situation for ash producers as well as the Federal government. There are growing quantities of fly/bottom ash residue. Ash producers must decide how this byproduct can be dealt with effectively and profitably. At the same time, government agencies such as the US Environmental Protection Agency (EPA), are commissioned by Congress to assure that solid, liquid, or gaseous material released into the environment is not harmful or offensive to human health and the environment. Additionally, the Federal government is often responsible for establishing and enforcing guidelines and standards governing the use of recycled materials. Several standards and guidelines governing the properties and use of ash in the US have been established by governmental agencies as well as by the ash industry itself. Of these, some have been developed for ash use by a specific federal agency. Others apply to the entire industry. The following is a brief identification of the major specifications for fossil fuel ash: • US Corps of Engineers - These specifications were first established in 1957. They delineate the physical and chemical requirement for pozzolans used in mass concrete. These specifications applied only to Corps of Engineers' concrete construction projects for locks, dams, and other mass concrete projects until 1977. At that time, a joint effort between the American Society for Testing and Materials and the Federal government produced a modified specification that is now generally applied. The Corps of Engineers' ash, however, retained certain aspects of its specifications for its own use, particularly in the area of handling and shipping fly ash to its own projects. Prior to transporting the fly ash to the corps, all potential sources for the ash must be inspected and approved as a supply source. All silos must be filled, sealed, and tested before the ash is released for shipment. The normal test period for the ash is seven days, although several testings may require up to 28 days. Once the fly ash has been released, it can only be shipped to US Corps of Engineers' projects. All shipments are made with a government inspector present during loading. After a truck or railcar is loaded, the silo is resealed until the next shipment. This procedure requires three silos, and a minimum of 454 t (500 st) each should be considered for each storage unit. All silos are strictly committed to Corps of Engineers' use and are not available for other commercial shipments. • US Bureau of Standards - This Federal agency maintains a standard testing sample of nearly every product used in the US. The accuracy of the fly ash chemical analysis is measured by a regular cement and concrete reference laboratory (CCRL) inspection and based on test results from a standard sample of cement. • US Bureau of Reclamation - This agency pioneered several projects using fly ash and required Federal Standard Certification for pozzolans. • American Society for Testing and Materials (ASTM) - This nongovernmental organization began preparing standards for fly ash sold and used in the cement and concrete industry in 1947, at the urging of ash marketing firms. Current standards define chemical and physical requirements and is entitled, "Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Portland Cement Concrete (C 618-80)." • State Highway Specifications - Led by Alabama, many states are moving toward permitting - and in some cases requiring-the use of fly ash in portland cement concrete and with lime for base stabilization projects for roads and highways. • Federal Aviation Administration (FAA) - The FAA acts in an advisory capacity. It has final approval on design specifications for airport construction projects. The agency has established a set of guidelines permitting the use of fly ash, and has approved several fly-ash-specific designs. The most current FAA fly ash projects

Jan 8, 1984

By A. J. Kroha, N. Wesis

Most copper mines produce both ore and low-grade "leach" rock or acid waters that contain recoverable copper. The sulfide ores pre¬dominate, and a portion that is too low grade for milling to produce concentrates for smelting, but has to be mined and trucked away anyhow, may be leached successfully with acid in dumps. Most of this leach material consists of sulfides and silicates or carbonates, and if the gangue is such that it consumes a high quantity of acid, this factor may rule out a leach operation. There are also valuable deposits that contain mostly acid-soluble copper, or occasional sulfide ores from which a sulfide concentrate can be roasted and acid-leached to produce a copper-bearing solution. Finally, there are milling ores in which the lesser part of the copper is acid-soluble and can be precipitated with iron or synthetic inorganic precipitants that produce metallic copper or copper sulfides that will float with the sulfides. Ordinarily, ores that contain copper associated with the sulfur ion, such as in the minerals chalcopyrite, chalcocite, bornite (and others), are milled to produce a 25-30% Cu concentrate for smelting, while a lesser amount of acid-soluble copper may be converted from solution to cement copper on iron scrap. A fast-growing percentage of such copper, however, is removed from solution with exchange resins or organic compounds in organic carriers such as kerosene (solvent extraction), then eluted with strong acid and subjected to electrolytic precipitation either in marketable form or as anodes that can be refined further. From the point of view of conventional copper smelting, copper flotation concentrates and cement copper are of chief interest in this chapter. Table I is a condensed open schedule for concentrates that generally run between 25 and 35% copper, and much less frequently as low as 12-15% or as high as 65-75% copper, the former being due to intimate relationship with pyrite (like the former United Verde Extension), and the latter representing such ores as the Bolivian Coro¬coro ore in which the copper is in the form of chalcocite in sandstone. These extremes are no longer common. When they occur, a special purchase schedule has to be negotiated. Included in Table 1, copper precipitates (cement copper) generally run from 70-85%a copper, and the same basic purchase schedule is used as with flotation concentrates. Sulfide Flotation Concentrates The sulfide copper concentrate produced in the mill as a flotation froth, with water then added for transportation of the heavy mineral particles from the flotation cells to thickeners, may run 60-80% water by weight, and the removal of water down to 25-50% by weight by means of thickeners, followed by further dewatering by continuous vacuum filters to 7-18% moisture by weight (depending on size of solids by screen analysis and also by content of clay) is a critical operation. Mill operators would like to produce a filter cake with 7-9% moisture content, but even with the help of steam on the filter this desirable condition is seldom realized when the concentrate is as fine as 80% -325 mesh. More commonly, the final concentrate is reground in pro- to produce best copper recovery and grade of concentrate (or molybdenite separation). In those cases, increasingly frequent, the filter product may not be a cake at all, but a mud that is hard to handle-even requiring a thermal dryer. Greater difficulty of form¬ing a manageable cake often comes from the copper-molybdenum separation by flotation, because the alkaline sulfides and hydrosulfides, or cyanide, or other similar reagents used for the separation, may leave the now relatively molybdenite-free copper concentrate even more difficult to filter. Handling a wet filter cake is difficult enough when its destination is only a short distance away-a matter of yards rather than miles. In those cases the filter cake may be thermally dried near the point of production, using rotary or multiple hearth, or fluidized-bed dryers. Alternatively, the concentrate may be pumped or carried in slurry form to the smelter and filtered there, or it may be spray-dried and compacted. For transportation to a smelter just a few miles to a few thousand miles away by ship or railroad other factors may be important, such as: in shipping by sea, avoidance of spontaneous combustion; in shipping by rail, losses by leakage if too wet or by wind and sun if too dry. It is the responsibility of the millman-usually the mill superinten¬dent-to make sure that his concentrates are in satisfactory condition when they leave the mill so that they meet these requirements: 1) They must have been accurately sampled and dry-weighed, the latter meaning that a moisture determination and gross weight must have been taken. 2) They must be dried sufficiently when necessary to prepare them for safe transportation. 3) They must arrive at the smelter with reasonable likelihood that they can be check-weighed and sampled fairly and equitably,

Jan 1, 1985

By H. Schubert

The flotation of sylvite and also some accessory minerals is performed in brines containing very high electrolyte concentrations. Under these circumstances the mechanims of collector adsorption exhibit some characteristics which will be discussed by significant examples: - flotation separation of sylvite and halite with n-alkylammonium salts and n-alkyl sulfates - flotation separation of kieserite and anhydrite with acylamino carboxylic acids - flotation of halite by collectors which are adsorbed by hydrogen bond formation.

Jan 1, 1988

By Wm. J. McCracken

HISTORICAL REVIEW OF BOARD OPERATIONS The Ontario Worker's Compensation Board was established in law enacted by the legislature of the Province of Ontario in 1915. It was designed to pay insurance benefits to injured workers, and at the same time to protect employers from legal suit. It was based upon an enquiry system rather than an adversary system such as that used in the courts process. Initially, the system was designed to pay compensation benefits and subsequently, to pay for the cost of medical treatment and pensions for disability and disease resultant from the effects of traumatic injury. In 1947, the Act was changed to include industrial or occupational generated diseases, not specifically related to traumatology. Such occupational diseases were therefore accepted and benefits paid subsequent to that date. As will be discussed in several minutes, even today the vast preponderance of compensation claims with the Ontario Board continues to be related to the effects of trauma. HISTORICAL REVIEW OF EXPOSURE TO RADON GAS DECAY PRODUCTS In some areas of Ontario, especially in Northern Ontario, there is a natural leaching of radon gas from the underlying rock formation. This constitutes very low levels of radon gas decay product radiation exposure to those persons coming in contact and inhaling these substances. This paper however is designed to discuss the occupational generated types of radon gas exposures. For many years dating back to the 1930's, partially refined ores were being shipped from Northern Canada to a refinery located at Port Hope, Ontario, still in operation and currently operated by Eldorado Nuclear Limited of Canada. Initially, the purpose for the operation was extraction of radium to be sold on world markets for medical treatment purposes. With the advent of World War II, this market collapsed. Subsequent to World War II, the availability of other sources of radiation for medical radio-therapy generally replaced the requirements for radium. During World War II, a new market opened up for the Port Hope refinery however as work into nuclear chain reactions and the development of the atomic bomb identified the need for uranium and enriched uranium. During the period of operations where radium was being extracted at the Port Hope refinery, it is now known that an identifiable radon gas hazard did exist. This hazard disappeared when the production line for extraction of radium ceased operations. In 1954, uranium mining operations opened up in Ontario at two locations, Bancroft and Elliot Lake. At the peak of operations, 16 mines were operational and 11,000 workers were employed in these mining operations. A high level of mining activity continued over a 10 year interval with the Bancroft Mines closing permanently in 1964 following a 10 year life of operation. The other mines in Elliot Lake closed about the same time with the exception of two uranium mine operations which have continued to be operational up to the present time. By 1965, due to a dramatic drop in world demand for uranium, the total work force had fallen to 1/10 of the peak work force, and approximately 1,300 workers remained in employment. It is of interest to note that one significant difference in the work environment between Elliot Lake and Bancroft was the high silica content of the Elliot Lake ore. This gave rise to a number of cases of silicosis developing in relatively short intervals of time in the Elliot Lake miner population. No cases of silicosis were identified from the Bancroft operations. Based upon the experience in investigating and evaluating actual cases of lung cancer in the uranium miners over the years, the medical staff at the Ontario Board also developed the impression that radiation levels were much higher in the Bancroft operations, especially in the earlier years of operation, than at Elliot Lake. This resulted in accumulation of higher levels of Working Level Months (WLM), usually over a shorter exposure interval in many of the cases. This aspect will be further evaluated in this presentation. Subsequent to 1965, the work force remained quite static in numbers until 1975. At that time, there began to develop an increase in the work force, and this increase is continuing at a moderate rate up to the present. INITIAL METHOD OF HANDLING LUNG CANCER CLAIMS The first lung cancer claims in Ontario from uranium mining operations were accepted on the perceived cause-effect relationship. This relationship was based upon the data from the Colorado observations and the Czechoslovakia data. Initially, a series of regression equations on mortality were developed and used to estimate the effect of exposure to low cumulative doses of radon daughters as it might relate to the frequency of occurrence of lung cancer at any particular cumulative exposure level. A probability of cancer being radiation induced as against it being caused from other factors was calculated. This method was discontinued subsequent to 1972 due to problems encountered in carrying out this complex evaluation. Thereafter, each case was dealt with on an individual basis, being based upon whether or not the tumour was of the oat cell type, a cumulative exposure in excess of 120 WLM; latency periods in excess of 10 years, commencement of mining prior to

Jan 1, 1981

By E. Wiewiorowski

A new technology for recovery of metals from spent catalysts containing aluminum, cobalt, molybdenum, nickel and vanadium was developed. The catalysts are decomposed in two consecutive pressure leaching steps. Sodium aluminate-sodium hydroxide systems are lixiviants in both leaching steps. Selective extraction of molybdenum and vanadium is achieved in the first leaching step. The leach liquor is processed for separation and recovery of these two metals. The residue from the first leaching step is further processed in a second leaching step where alumina is solubilized. The residue from this operation is a nickel-cobalt concentrate. Alumina is separated from the second stage leach liquor by precipitation; the depleted liquor, a sodium aluminate solution, is recycled to the first and second leaching step. This technology has advantages over other approaches for the recovery of metals from spent catalysts because no solid waste is generated.

Jan 1, 1988

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By K. Hanna

This paper describes a method to improve coal mine entry intersection design. The method considers the effect of in situ stresses, local geologic conditions, rock physical properties, and mining sequence. Development of the method is discussed, including the results of field instrumentation studies and numerical modeling investigations. Data required to evaluate the effects of roof span, mining sequence, entry orientation, and bolting patterns on intersection stability are also presented. Ground control studies conducted by the U.S. Bureau of Mines in two underground mines in the Illinois Coal Basin have shown that in situ horizontal stresses and roof geology have a critical effect on intersection stability. Methods to reduce the adverse effects of these parameters are emphasized. Typical failure behavior associated with specific geologic and horizontal stress conditions is' presented to illustrate proposed control methods to alleviate adverse ground conditions.

Jan 1, 1988

By H. R. G. Steeghs

Recently developed organic binder systems have the advantage of eliminating bentonite contamination. This results in better chemically reactive taconite pellets. Both acid and fluxed pellets show increased R40 reducibilities, whereas mechanical and physical properties of the taconite pellets are not adversely affected. Blast furnace performance of these pellets is excellent, and substantial economic benefits are achieved.

Jan 1, 1989