Search Documents

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

By Ryan P. Sullivan, Ben D. DiFiore, Robert J. Auber, Michael A. Piepenburg, Lisa M. Smiley

Pollution to Lake Erie will be significantly reduced by the Westerly Storage Tunnel (WST) system, which is mainly comprised of a 10,000-ft long tunnel and a dewatering pump station in the downstream tunnel shaft. Separate construction contracts for the tunnel and pump station required careful management of the interface risks. A key decision was to decouple the projects by relocating the mining shaft away from the pump station. The need to receive the tunnel boring machine (TBM) in the pump station shaft was eliminated by dismantling the 28-ft diameter TBM in the tunnel then carrying it back through the tunnel and up the mining shaft. This paper discusses how interface risks were successfully managed during design and construction to limit overall schedule impacts.

Dec 1, 2022

By J. A. Lombardi

"EXECUTIVE SUMMARY The use of membranes for the treatment of Acid-Mine-Drainage (AMD) water has been a 35 year mining industry quest that has only recently produced commercial scale Zero-Liquid-Discharge (ZLD) plants. The process of development of the membrane treatment of AMD has been defined by the water treatment industry’s efforts to control gypsum scaling of the membranes, an artifact of the concentration of calcium and sulfate ions on the concentrate or “brine” side of the membranes. Improved anti-scalants, changes to membrane surface geometry and a lowered permeate flux rate were all part of solving the calcium sulfate (gypsum) scale formation problem. Whether used singly or as part of a multi-stage membrane treatment process, the production of “left over” membrane concentrate or brine, in any volume large or small, was a second barrier to adoption of the method by the mining industry. The two identified “final brine” treatments were a) solar evaporation ponds and b) mechanical evaporators. Brine disposal by solar means is typically site limited to flat terrains or high net evaporation locations. Mechanical evaporation-crystallization is applicable at all sites but, typically, at onerously high ownership and operating costs. Miwatek, a South African water treatment start-up, has entered the mining AMD ZLD marketplace with two new, pilot-scale tested, processes, both of which are predicated on the innovative treatment of a reasonably concentrated AMD and neither of which produces a final brine that requires disposal. In the Miwatek Brine Treatment, MBT, method the membrane brine is caustic pH adjusted and de-calcified precedent to passage through a second membrane plant. The caustic is generated on-site by a lime treatment of the second-membrane concentrate. The first- and second-stage permeates are blended for discharge. The process usually yields no “final brine” for disposal. In the Miwatek Ettringite Treatment, MET, method a low pH first-stage membrane brine is lime treated in two or three steps in the presence of aluminum in a way that metal hydroxide and calcium sulfate solids are formed and purged from the system. Sufficient aluminum is often present in the feed water to, with judicious recycling, enable operation of the lime-aluminum treatment without the purchase of outside aluminum reagent. The first-stage membrane permeate is blended with the lime-aluminum treated membrane concentrate for discharge. The indications are that the method can comfortably meet the low 250 -500 ppm SO4 discharge water quality standards that have most recently been proposed in South America. The process yields no “final brine” that requires disposal. Projected own-operate costs for the MBT and MET systems are less than the estimated costs for all identified alternative treatments."

Jan 1, 2015

By Paul C. Schmall

In recent years, several geotechnical methods have been successfully applied to ash pond closure. These include modified dewatering techniques with wellpoints and wells to physically drain the material, soil mixing to create a soil-concrete material for improved accessways as well as improved ground structures within ponds to act as barriers or gravity dams, and geotechnical instrumentation to serve as an early warning of the potential for liquefaction. Given the parallels between fly ash and sluiced in place mine tailings, the application of fly ash remediation method to mine tailings shows significant potential, as illustrated in this paper.

Feb 1, 2024

By Colin Irwin, Adrian Naranjo-Castillo, Christopher Petta, Eric Zarobila

The Shoreline Consolidation Sewer is a CSO control project in Cleveland, Ohio that requires the installation of 5,000 feet of 72-inch inside diameter pipe using microtunneling methods. After award, the contractor submitted a value engineering proposal to eliminate two deep shafts and install the tunnel in two drives instead of four. In an example of successful collaboration, owner, contractor, and engineer worked together during the initial construction stages to modify the design and update the contract documents. This paper examines the importance of exible requirements in contract documents and a collaborative environment between all parties to successfully deliver a project.

Jun 23, 2024

By J. S. Carman

As with the slogans of Madison Avenue, catch words or phrases frequently become topical. Much is heard these days of the confrontation between governments of developing countries and international mining capital. In actual fact, sadly there are too few cases of anything as positive as confrontation because such an action at least signifies a dialogue which may begin badly but end up fruitfully. Instead we have in general a climate of indifference and fear with the mining companies of note marking off most of the developing world as being unsafe for investment. There is an unreal air to this damaging impasse. The common sense and objectivity which are prerequisites of positive action are lost in a swirling cloud of mythology, embraced largely by governments. Let us examine some of the dangerous misconceptions.

Jan 1, 1977

By Dani Delaloye, Kas Zurek

Evaluating and selecting the appropriate excavation method is a key to the success of any tunnelling project. The benefits and risks of different methods should be well understood by the designer and communicated to the project owner to enable selection of a preferred method from a technical, social and environmental impact, cost and constructability perspective. For tunnels that have an internal diameter around 3 m, depending on the tunnel purpose and ground conditions, both microtunnelling with pipe jacking and tunnel boring machine excavation with a one- or two-pass lining may be feasible construction methods. Using the Ferry Road and Riverbend Combined Sewer Relief Project located in Winnipeg, MB as a case study, this paper will discuss the benefits and drawbacks of each method, including technical design, social, environmental, cost, schedule, and risk considerations.

Jun 13, 2023

By Moussa Wone, Jeff Peterson, Filippo Azzarà, Daniele Nebbia

The DC Water and Sewer Authority's Long Term Control Plan includes tunnels, sewer separation, pumping station rehabilitation and green infrastructure to reduce combined sewer overflow (CSO) discharges to the District waterways. The Northeast Boundary Tunnel is a deep, large sewer tunnel that will reduce CSO discharges; signifi- cantly mitigate known chronic flooding in the Northeast Boundary drainage area and improve the water quality of the Anacostia River. This paper presents the unique combination of Owner and Contractor perspectives of the entire Project from conception through procurement, execution, and contract management, providing lesson learned, chal- lenges encountered, and solutions implemented to deliver the Project successfully.

Jun 23, 2024

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026

By Chris Lynagh, Lisa Smiley

INTRO PAGE

Jun 13, 2021

Contents

Jan 1, 1985

By Harry C. Oussoren, James C. Miles

A new seven kilometer long subway line is being constructed through dense glacial soils under a major thoroughfare in Toronto. Eductor, deep well and vacuum wellpoint systems are being used to lower the water levels by as much as 16 metres for the construction of the twin tunnels and associated structures. The design and performance of the dewatering systems will be described. Unanticipated difficulties and their solution will be presented.

Jan 1, 1999

By D. Zaharaki

The present experimental study underlines the advantages of factorial design in environmental, geotechnical and waste management experimentation. A typical case study regarding solidification of metallurgical wastes is presented and the main effects and interactions of three main factors are determined in order to establish the optimum experimental conditions in terms of compressive strength. Finally, a regression equation that predicts accurately the real compressive strength of a specimen under various experimental conditions is derived.

Jan 1, 2005

By F. Repmann

Waste-dumps originating from the mining industry constitute a serious environmental problem if they are not properly rehabilitated. Industrial and domestic sewage sludge from waste water purification plants on the other hand constitute a problem of environmentally acceptable disposal as these residues contain a large number of potential contaminants. The current project aims at developing an integrated methodology to rehabilitate the mining waste-dumps by the use of sewage sludge so that the two mentioned problems will be solved at once.

Jan 1, 2002

By William F. Riggs

In the fresh application of a frother, collector, or the change of any particular reagent, the interaction caused by this change is often overlooked since we attempt to solve a problem or improve a situation with use of a particular reagent without regard for the Interactions or side effects. When a particular reagent is added to a flotation circuit or substituted for another reagent, a series of chemical reactions occurs which. In turn, will create different physical responses. This discussion will provide a series of examples which have actually been experienced by the author.

Jan 1, 1994

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By H. S. Kibler, A. E. J. Gallagher, J. J. Sebesta

A review will be made of the nature, value, costs, and factors associated with industrial minerals production in general. Comparisons will also be made between some of these data and similar criteria for metallic mineral production.

Jan 1, 1987

By G. C. Anderson

The Cleveland Cliffs NOLA electronics and software upgrade is a Windows based system that simultaneously controls two Texas Nuclear NOLAs and associated sampling. It uses new spectrum analysis and algorithms to produce accurate, linear silica measurement with slurries that range from 5 through 50 percent solids. This linearity allows us to achieve a reproducible procedural calibration. The hardware consists of readily available shelf items, is extremely redundant and eliminates all NIM bus modules.

Jan 1, 2003