Search Documents

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By Paul C. Miclea

Hanford Reservation, in the State of Washington, with its deep basalt formations, is one of the three sites recommended by the Department of Energy for detailed investigations in order to select the first nuclear waste repository in the United States. Information obtained from several deep bore-holes drilled at Hanford indicates that the underground facility can be developed in one of the major basalt flows belonging to the Grande Ronde Formation in the Columbia Plateau, at depths greater than 3200 ft. One of the main concerns in the underground repository design is the achievement of acceptable environmental conditions during the development and the operation of the repository. For this, ventilation and air-conditioning are of prime importance and should be fully addressed. Besides the factors that determine the airflow requirements to meet the personnel and equipment operation needs, there are two major concerns that impact on the ventilation system design: the temperature of the in situ virgin basalt rock and the influx of groundwater. These two factors are related by the fact that the groundwater has the same temperature as the rock itself and they both constitute main sources of heat underground. Current information indicates that the temperature of the virgin rock at a depth of around 990 m (3250 ft) is 52°C (12S°F). However, there are some indications that the rock temperature at the selected horizon might be higher. This paper addresses the impact of the virgin rock temperature on the ventilation system and air-cooling requirements. Graphs with heat loads and cooling required for different rock temperatures have been prepared for a given model and network, using computer techniques for simulating the climatic parameters.

Jan 1, 1987

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital ; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing and sales, or public affairs, a career opportunity is available in the industry.

Jan 1, 1981

By K. Adam

The sustainable management of solid wastes, including the wastes emanating from portable batteries, consists one of the main objectives of the current EU Environment Framework Programme. Overall reduction in the quantity and volume of disposed wastes, elimination of dangerous species within the waste streams and wastes recycling comprise specific targets of this policy. Within this framework a Greek funded research project entitled ?Development of an Integrated Alternative System for the Environmentally compatible Management of Used Batteries and Accumulators - DIASBAT?, was recently completed by a research team consisting of major Greek Battery producers and retailers, Research Organisations, Universities and Environmental Consultants. The aim of the project was the development of an Efficient Alternative Management System for spent portable Batteries and Accumulators, (B&A), in compliance with the prevailing EU and national environmental legislation, taking advantage of the state-of the art technology. The present article summarises the research carried out within the DIASBAT project in order to review and develop a set of sustainability indicators for the assessment of the effectiveness of Spent Portable Batteries Management Systems (SPBMS). Based on the European experience and practice, various indicators were initially examined regarding the performance evaluation of SPBMS. Specifically, the indicators used in European studies conducted to assess the environmental, social and economic impacts of the recently issued Batteries Directive 2006/66/EC, as well as the indicators used by European Collection and Recycling Organisations (CROs) to assess the performance of SBPMS across Europe were presented and analyzed. Additionally, the set of indicators used within DIASBAT to assess the effectiveness of alternative Spent Portable Batteries Collection Schemes developed within the project, are presented. The experimental collection networks of the DIASBAT project included schools, selected retail stores and a pilot network set up by the Greek Institute of Geology and Mineral Exploration (IGME). From the evaluation of the various indicators, it was deduced that in order to assess an Integrated Spent Portable Batteries Alternative Management System, a multi criteria analysis approach is required. Within the general principles of sustainable development, there is a need for different qualitative and quantitative indicators to be combined, taking into consideration critical parameters such as: annual portable batteries collection rates, compliance with the targets set up by the prevailing European and national legislation, economic performance of the System - and finally social criteria - environmental sensitization according to age, gender, economic prosperity, educational level etc.

Jan 1, 2007

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By J. P. Mogan

As diesel exhaust contains a mixture of several materials of varying degrees of toxicity which interact to a currently undefined extent in their effects on health, the prescription of a quantity of ventilating air to dilute the exhaust to a safe level is necessarily, to some extent, arbitrary. Some jurisdictions rely on the application of a safety factor to a single "governing" component (usually nitric oxide for most modern diesel engines). Others specify that the total of the "adjusted" concentrations (actual concentration divided by maximum permissible concentration) not exceed "one" for related constituents (irritant gases for example). Neither of these approaches, however, takes account of the interaction of the gaseous constituents with diesel soot (although many studies verify such interactions), nor do they provide any economic incentive for reducing pollutants which are not included in the criteria for ventilation. Because of these factors, the Canadian Department of Energy, Mines and Resources awarded a contract for a study of the current literature bearing on the "Health Implications of Exposure of Underground Mine Workers to Diesel Exhaust Emissions" (1). One goal of this study was the formulation of a new ventilation criterion. The contractors, Ian W. French and Associates, studied more than 1500 literature citations which they interpreted in a 350 page report and summarized in a companion 1600 page annotated bibliography. In the recommendations section of the report, they defined a new 'health effects index' or ventilation criterion "V" as follows: [ ] The contractors consider that a "V" between 3.0 and 4.0 poses a moderate threat to health which could be alleviated by the use of protective equipment such-as filter helmets. If V exceeds 4.0, an increase in ventilation quantity to reduce the pollutant levels is indicated. In the case of mines with a quartz content in excess of 20% in the ore, the contractor recommends that a term. [Quartz]/ [Threshold Limit Value Quartz] be added to the equation, and [2.0 = ?v? = 30] be the range justifying protective equipment, with added ventilation if "v" exceeds 3. A degree of pragmatism was inherent in the development of the equation, as the contractors recognized that the components of the index, if it is to be useful in the near term, should be within current routine underground environmental assay capability.

Jan 1, 1980

By A. J. Hendron, L. L. Oriard

INTRODUCTION Controlled blasting is used at some time during most civil engineering projects where there is rock excavation. Controlled blasting is often necessary because the blasting must take place in the near proximity of adjacent structures. In other instances, the blasting is controlled because a smooth perimeter is desired to minimize rock support and overbreak. The construction of tunnels and shafts for subways, rock excavations for foundations and the excavation of road cuts for interstate highways, sometimes require blasting operations which must be conducted in an urban environment. Unfortunately, blasting operations produce unwanted sounds and vibration along with their beneficial effects. Thus, in the writing of specifications for blasting in an urban environment, potential damage to adjacent structures by ground vibrations must be considered, possible damage to windows from airblasts must be considered, potential damage from fly rock must be considered, and the discomfort to people from ground vibrations, airblast, and noise must be taken into account. The contractor or the owner's engineer is faced with determining the maximum weight of explosives which may be detonated without damage to structures on adjacent property. If the weight of explosive is overestimated, the resulting damage to adjacent structures may result in costly losses. But, if the engineer or contractor is too conservative, and the weight of explosive becomes too restrictive, progress of the project may be curtailed and the cost of excavation will increase accordingly. The potential for damaging adjacent property is becoming more important in construction operations today. In the past, the plaintiff had to prove negligence in some states in order

Jan 1, 1997

By Takeshi Tanaka, Yasuhiro Komamura, Yuusaku Tominaga, Takayoshi Iwamoto

In order to assist better countermeasures for ventilation control in normal/abnormal condition of mine ventilation network in real time, branch relation table derived from a macroscopic characteristic of ventilation network is introduced in this study. The main results in this study are as follows; 1) One of macro characteristics of a ventilation network, as a relation between airflow rates in two branches chosen arbitrarily, is specified under the change of aerodynamic resistances in a branch. Airflow rate in a branch can be estimated by airflow rate in other branch changing aerodynamic resistance by using empirical formula. The empirical formula by computer simulation of the Horonai coal mine, Japan is considered to be a one-valued function with monotone or extremums. 2) A branch relation table shows the macro characteristics, mentioned above, of all the set of two-branch combinations in a network. Elements in the table give both information of control possibility range of airflow rate and total number of extremums in an empirical formula. 3) It is important that when aerodynamic resistance change in a branch is estimated by measuring airflow rates in two typical branches, the two branches should be chosen from branch combinations with monotonous relation in the branch relation table. 4) A flexible expert system to assist ventilation control in the specified branch in real time has been developed by using a branch relation table for a ventilation transfer diagram of the specified branch, such a coal face and an advancing face. A fuzzy reasoning is utilized in the recognition of the safety factor, methane concentration, in the system. And when conviction degree in recognition for methane concentration at the specified branch is too low, the system searches for other branch combinations in the branch relation table stored in the system, to use other ventilation transfer diagram of the specified branch. When a needed ventilation transfer diagram is not stored in the system, the expert system asks automatically the ventilation simulation from other computers linked to the main computer automatically. The system repeats consultation until conviction value of safety in the specified branch approached

Jan 1, 1993

By Charles U. Keranen

The Tilden Mine is an iron ore mining, processing and pelletizing facility located on the Marquette Iron Range in Michigan's Upper Peninsula. It has a designed capacity to produce 8 million long tons of pellets annually from 21 million long tons of crude. It is a partnership owned by The Cleveland-Cliffs Iron Company, Algoma Steel Corporation, LTV Steel Corporation, the Steel Company of Canada, Wheeling Pitts- burgh Steel Corporation and the Sharon Steel Corporation. Cleveland- Cliffs manages and operates the Tilden. The crude ore averages 35% iron and is primarily non-magnetic iron oxide and silica. The major ore mineral is martite. Hematite, earthy hematite, goethite and magnetite are also present. The principal gangue mineral is chert. The ore grains are mostly in the 10 to 25 micron size range which necessitates very fine grinding for liberation. The concentrating process is the most complex one used in the iron ore industry. The unique technology for Tilden was developed in the mid and late 60's. The design and construction occurred in the early 70's and operation of the first phase which was of 4 MLTPY capacity began in October. 1974. Expansion of the facility to the current 8 MLTPY capacity was completed in 1979. Chemicals are the key to the beneficiation process at the Tilden Mine. The flowsheet utilizes selective flocculation - desliming, cationic silica flotation and concentrate dewatering by thickening and filtering. Nine different process chemcals are used. The control of the reagent feed systems is highly auto- mated. The entire concentrator is operated from a central control room. The concentrator flow diagram is presented in figure 1. The plant consists of 12 primary autogenous grinding lines, a common crushing circuit to handle an intermediate product within the primary grinding section, 24 pebble mill lines with cyclones and deslime thickeners, 12 flotation lines, 4 concentrate thickeners and slurry tanks, 8 lines of filters with six machines per line, and 2 tailings thickeners. A pumping system was installed in 1980 to permit the direct return of tailings thickener overflow water back to the reuse water pumphouse.

Jan 1, 1986

By S. Ostap

INTRODUCTION Paradoxically, it has been found that the people who are the most aware of the origin, mineralogy and composition of bauxite are also the people who are the least aware of how bauxite composition affects its treatment by the Bayer process. These people are the exploration and mining geologists normally associated with aluminum producing companies. The purpose of this paper is to give some idea of how the concentration and physical nature of the different minerals found in bauxites affect the operation of the Bayer process used to extract their alumina content. The bauxites we will consider here will be only the tropical bauxites such as occurring in Jamaica, various countries in South America i.e. Guyana, Surinam, Brazil, African bauxites, Malaysia and in Australia. When we speak of the Bayer process, it will be the North American version of the Bayer process using low caustic concentrations and bauxite digestion temperatures varying between 130° to 250°C. TABLE 1 shows the minerals and elements of interest occurring in tropical bauxites. The minerals and elements listed in the table do not by any means represent all of those identified in bauxites. Using mass spectrographic analysis on six bauxites from different geographic locations, we managed to identify between 50-60 different elements. Fortunately, only about 13-14 of these elements possess the necessary chemical properties to be able to accumulate in caustic Bayer solutions. The remainder are either not attacked, or form insoluble reaction products with some main liquor component, i.e., hydroxide, aluminate or carbonate, or reprecipitate with alumina trihydrate during the precipitation stage.

Jan 1, 1984

By Milton F. Searl

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technlogy are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 1, 1980

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduction through semi-infinite homogeneous and isotropic airway walls with convective heat and moisture transfer between their wet or dry naked surfaces and mine air with time variable temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for computation of the temperature distribution and surface temperature of the airway walls and floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. The presented solutions are derived for general conditions and they could be easily adapted to the actual ones. Results of the model represent basis for balancing heat and moisture transfer between mine air and its surrounding in deep mines under time variable temperature and humidity of the air and enable us to solve complicated dynamic changes of mine air temperature and humidity in an airway system by relatively simple mathematical tools. INTRODUCTION The importance of unfavourable influences and the costs of condition arrangements increases with mine depth. Precision demands on the methods which predict the environmental condition changes and by which it is possible to optimize condition arragements are still increasing. Environmental conditions in deep mines are determined especially by flow velocity, barometric pressure, temperature, and humidity of mine air. Therefore new and more exact mathematical models of mine air flow through airway system and those of heat and moisture transfer between mine air and individual important sources of heat and moisture are developed. The paper presented deals with description and solution of problems of heat and moisture transfer between mine air and airway walls as the rock mass is one of the important heat and moisture sources in deep mines. There are several different approaches to the problem. In some models the moisture transfer between mine air and airway walls is not considered at all. In other models the moisture transfer is described only by certain empirical coefficients. Simultaneous heat and moisture transfer is described seldom. This paper tries to describe in a simple way simultaneous convective heat- and mass-transfer processes taking place on wet naked surface of airway walls by means of corresponding

Jan 1, 1993

By Searl. Milton F.

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technology are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 9, 1980

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 1, 1987

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By Stanley W. Ivosevic, Mark E. Emerson

Introduction Metals exploration activity is moderately intense in the US despite the 1981-82 recession in the mining industry. Although exploration expenditures are significantly less than the 1981 peak, quality and goal orientation of current exploration are high. Major foreign and domestic mining companies as well as nonmetal companies had been attracted to invest in minerals in the US. Its capital markets, political stability, and open-door policy are attractive for hard mineral explo¬ration, particularly in the West. The approach was to either acquire fully or partially developed ore bodies through merger and acquisition, or to fund large scale exploration programs in search of bulk-tonnage deposits. The acquisition avenue has not proved the panacea envisioned for overcoming lack of substantive mineral development. Nor has the decentralized approach to exploration that was adopted proven cost-effective. The emphasis on gold, to the exclusion of all other commodities, raises questions regarding the direction of exploration in the US for the rest of the 1980s. Overview More than 300 companies are active in metals exploration in the US. These range from established, well-known domestic and foreign corporations to hurriedly incorporated, unknown companies financed by having promoted mineral prospects or occurrences of questionable quality. Junior companies tend to be oriented toward property entrepreneurship, rather than the development of minerals resources. These companies have helped maintain mineral lands from prospect to production by holding blocks of property intact during periods of exploration inactivity. This was done through promotional efforts, even though few properties that attracted major venturers proved to have real merit. Exploration objectives of senior and junior exploration companies currently embrace only a few commodities. Arranged in approximate descending order of priority, these are: precious metals; base metals in monometallic or polymetallic deposits; strategic metals, such as tungsten, tantalum, and tin; unconventional commodities, such as diamonds; ferrous metals; and commodities such as beryl, zeolites, and barite. Prospectors are important in searching for these targets. In the US, where they have been financed by major and junior companies, prospectors have proven a useful and low-cost means of locating gold prospects (e.g. the Alligator Ridge property in Nevada). The tenacity and persistence of independent prospectors have been factors in discovering properties rejected or overlooked by professional geologists (e.g. Lornex mine in British Columbia). This has been realized by the provincial government that grubstakes bona fide prospectors. Exploration interest in commodities has always been cyclic with price. Gold is one of the few metals that has experienced a price increase of such magnitude to warrant attention. The potential for realizing adequate operating margins for the Nevada open-pit "no-see-um" gold deposits is great. The present declining gold price, however, may indicate that this emphasis on gold, to the exclusion of other commodities, is shortsighted. Mining companies have been the last to react to price increases, opening new mines based on unrealistic market expectations. A scenario could develop where plummeting gold prices bring recession to the gold industry, as lately occurred in uranium, molybdenum, and copper. US Exploration Climate The US is attractive for exploration due to its strong mineral po-

Jan 4, 1984

By Robert W. Wheeler, Richard G. Ames, Robert B. Reger

Introduction The use of diesel engines as an alternate power source in US underground coal mines has been a controversial step towards more efficent mining practices. Three areas of potential benefit are foreseen. First, diesel-powered mining equipment is believed to be more efficient, resulting in less occupational risk for any given amount of production. Second, diesels are believed to pose fewer intrinsic hazards, especially those related to fires and ignition of combustibles. Finally, several other health and safety advantages are foreseen for diesel units. Each of these issues will be discussed separately. Diesel Efficiency Proponents of the use of underground diesel-powered mining equipment point to increased production efficiency due to greater maneuverability, speed, power, and payload (Bradbury, 1973; Jorgensen, 1982; Ogden, 1978; Wenberg, 1979; Olsen, 1980). Units most suitable for diesel power include LHD vehicles, shuttle cars, personnel carriers, and maintenance vehicles. Estimates of increased efficiency vary from 60%-300% and more (Wenberg, 1979). Increased diesel mining efficiency is usually viewed as making it practical to mine lower grade seams. Diesel units can also operate over a wider range of floor pitches and distances than electrically-powered units, thus allowing mining of seams with special mining problems (Olsen, 1980). Diesel application is not a universal substitute for electrical power. For example, continuous miners are unlikely diesel candidates. Reduced Intrinsic Hazards Proponents of diesel use have pointed to the increased safety potential due to a reduction in electrocutions, arcs, burns, underground cable fires, and methane ignition (Ogden, 1978). Diesel units are frequently employed in maintenance activities for lifting and moving, and for coal cleanup. Thus the case is made that diesel use, by making powered operations more conveniently available, reduces the incidence of lower back injuries and related causes for days lost due to disability (Olsen, 1980). Several other issues relating to diesel safety have also been suggested. Diesel units can continue operation even during power outages allowing, for example, personnel evacuation. The maneuverability of diesel units make them particularly attractive in difficult physical conditions, such as long haulage from the face to the belt and in areas where water is deep. The case for diesel use focuses heavily on the potential for a "per worker" reduction in accidents, or a reduction in the severity of accidents. Since accidents are a major part of the health impact of mining, a reduction in accidents and resulting injuries would make a major contribution to the health of coal miners. Opposition to Diesel Use Opposition to the use of underground diesel mining equipment in the US seems to have started with the United Mine Workers of America. Some opposition to US diesel use has been based on a widely publicized 1976 letter from NIOSH to Mine Enforcement and Safety Administration administrator Robert Barrett (NIOSH, 1982). In essence, this letter warned that while insufficient evidence existed as to diesel effects on underground coal miners, NIOSH had concerns based on prior knowledge of separate diesel exhaust constituents and the potential for interaction between these constituents and coal mine dust. Current opposition to underground diesel use has focused on respiratory health effects related to diesel emissions, particularly nitrogen dioxide (NO,), carbon monoxide (CO), and particulate content (Barrett, 1982). Through

Jan 4, 1983

By Thomas J. Mason, Geno Saccomanno, Victor E. Archer, Philip C. Prorok

INTRODUCTION A population of several thousand uranium miners in the Colorado Plateau region of the United States has been under surveillance since 1957 using sputum cytology and other procedures. Attempts were made to collect sputum samples annually for those miners showing normal sputum or only minor abnormalities, and on a semi-annual schedule for miners having more severe cytological abnormalities. For individuals having carcinoma in situ or malignant cells in their sputum, samples were taken more frequently. As in any human population, however, these schedules were not always adhered to, and samples were often acquired less often than scheduled. On the basis of the thousands of sputum readings that have resulted from this surveillance, one can calculate the durations or sojourn times which individuals spend in the various cytologic states into which the sputum readings are classified. This paper presents some preliminary, descriptive results concerning relationships among the cytologic state duration distributions in this population, and their associations with other variables such as radiation exposure and cigarette smoking. There are several reasons for studying cytology results in this observational setting. Of considerable interest is the opportunity to gain insight into the preclinical natural history of lung cancer. Such information would be valuable in the future design and interpretation of screening programs for the early detection and treatment of lung cancer, should this activity prove to be of benefit in experimental trials. Secondly, it is of interest to determine if some characteristic of sputum cytology readings can be utilized to determine a decision point at which to transfer a uranium miner to another job category within the industry in order to effectively reduce his probability of developing lung cancer. For example, a reading of moderately atypical cells in the sputum has been suggested as a possible decision event which would be sufficient to warrant such a transfer. In the analysis which follows, an attempt will be made to develop information relevant to these issues. The data base for our analysis, largely developed over a period of more than 20 years by Drs. Geno Saccomanno and Victor Archer, contains sputum readings classified into one of eight cytologic states: normal, metaplasia, mild atypia, moderate atypia, marked atypia, suggestive, suggestive-equivocal, and malignant. The two suggestive states will not be considered as these categories seldom contain enough observations to generate meaningful results. The duration in a given cytologic state for a given individual is calculated as the sum of the intervals between consecutive sputum readings in that state. When two consecutive readings are in two different states, half the between-readings interval is assigned to each of the two states. Among all individuals in the data base, only those having at least two sputum readings are used so that a duration can be calculated. Furthermore, the analysis is limited to individuals whose successive readings are no more than 24 months apart, so as to focus on a population which was under surveillance on a reasonably regular basis. RESULTS The overall distributions for the cytologic states are displayed as histograms in Figures 1-3.

Jan 1, 1981