Search Documents

By Y. C. Kim

This paper describes the implementational aspects of a blast hole kriging system that has been developedfor the purpose of daily ore/waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore/waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBMIPC AT or XT computers, using the Fortran language and supplemented by a few assembly language routines for the bit- map manipulation. This paper emphasizes the practical implementation requirements of the system and discusses system design considerations.

Jan 1, 1991

By Akira Usui

Ferromanganese crusts on topographic highs in the western Pacific Ocean are believed to be potential resources of cobalt, nickel and platinum. Earlier shipboard geological and geophysical studies by Japanese organizations have focused on mapping of distribution of thickness and metal contents of the deposits when estimating the total reserves. This paper summarizes our attempt to obtain more feasible data of distribution patterns and configuration of the deposits which are important parameters for resource evaluation at some seamounts in the South Pacific Ocean. Morphology of the seamounts and micro-topography of the sea floors are described using shipboard acoustic remote sensing, deep-tow sonar images, and TV/camera. [ ]

Jan 1, 2008

By C. Garcia, H. Arias, J. D. Miller, C. L. Lin

The question of ultimate recovery in heap leaching operations is always of particular concern with respect to economic considerations. Of course the particle size distribution is a critical factor which determines ultimate recovery and which must be established based on a balance between the extent of mineral exposure and transport phenomena. Now it seems that the ultimate recovery for a given particle size distribution can be established from mineral exposure analysis by x-ray microtomography (XMT). Using recently developed software, micro-CT data can be used to determine the fraction of mineral exposed and thus the ultimate recovery. Examples of mineral exposure analysis are given for the copper heap leaching operation at Zaldivar, Chile.

Jan 1, 2002

By J. L. Ellenberger, P. W. Jeran

A deep longwall coal mine was instrumented with a three-dimensional microseismic system in order to help determine the exact strata mechanics associated with the rock failure, redistribution of stress and the associated gob formation from the longwall. Overall, 5,000 well calibrated seismic events were recorded during the mining of the panel. Analysis of these events showed a close correlation between the seismic activity and advance rate, and that the majority of the recorded seismic activity occurs in the immediate area of the advancing longwall face.

Jan 1, 2002

By S. P. Lucido, I. Iwasaki

The potential of controlling heavy metal ions in effluents from discontinued mining operations and waste rock piles has been investigated. A fresh water green alga, Cyanidium caldarium, was found to have the potential to remove Cut' from solutions while exhibiting high tolerance to acid conditions which are commonly encountered in copper-nickel mine drainage. The process has the potential for application as a low maintenance metal decontamination system. The growth requirements and copper removal characteristics of this microorganism are described.

Jan 1, 1991

By B. Das, D. D. Mishra, M. I. Ansari

Experiments conducted with a 75-mm-diem hydroryclone have shown it is possible to obtain an iron ore concentrate containing 60% Fe. 2.65% SiO2, and 4.0% Al2O3 from Barsua iron-ore washing-plant slimes. About 60% of the iron values are recovered from slimes containing approximately 49% Fe, 8.9% A1203 and 11% SiO2. The obtained products can be used in the sinter feed for iron and steel making. The key to achieving process success lies in establishing the correct cut point (d50) of the hydrocyclone through the manipulation of operating and design variables, such as spigot and vortex finder diameter, solids concentration and operating pressure. The cyclone efficiency is represented by the partition curve. The cyclone performance, evaluated mathematically from the reduced efficiency curve, is represented by the equation Y = 100[1 -exp(-axb)], where: •X = did 50, •Y = corrected of efficiency (%) and •a and b are constants.

Jan 1, 1994

By Deli Hu, Xiangze Shu, Cai Wang, Hongfu Liu

To detect the place and range of fire is one of the key technologies in the extinction of coal mine underground fire. A fire-prevention and extinction research team of Shanxi Mining College have successfully carried out a program detecting the place of fire with radon. In the past four years the authers have done the detecting work in several mines in Shanxi Province, such as Gujao, Xuangang Louan and Ningwu. The place and scope and the trend of underground fire of coal mine can be now exactly estimated. The data and information from detecting provide a reliable basis for drawing up the scheme to extinguish underground fire and extract mineral coal securely. The principle and method of fire detecting based on radon on surface, the data processing and analysis are discussed in this paper.

Jan 1, 1991

By J. -C. Roegiers, M. Thiercelin

Accurate toughness determinations are difficult to achieve in the case of soft or heterogeneous rocks. The existence of a large process zone ahead of the crack tip makes the determination of the apparent toughness crack length dependent, in the case of subsized specimens. In order to use practical size specimens, the authors propose a new toughness test, the Modified Ring Test, which pre- vents a largely developed process zone to form ahead of the crack tip. This test has also the advantage that its geometry is core-based. Numerical and experimental results are discussed.

Jan 1, 1986

By R. G. L. McCready, G. Dr. Heinrich, V. I. Lakshmanan

The objective of this study was to prove repeat loading capacities of physically stabilized fungal biomass from Penicillium sp. for the removal and recovery of uranium from mine water (Denison Mines). The testwork was carried out on a bench scale in small columns and proved that it is possible to stabilize the biomass in an inorganic compound. A lifetime of 10 loading-eluting cycles of the stabilizer biomass product was obtained by additional pretreatment. Sodium carbonate proved to be an effective elution medium. Loading and elution can be controlled by the pH values of the column. The effective loading capacity until the breakthrough point is approximately 70 % of the overall loading capacity. The loading capacities of the stabilizer biomass product are comparable to that of the original biomass. Uranium recoveries of 90 to 99 % were achieved during the loading and eluting under optimized conditions. Depending on the used biomass the described process might be applicable to remove uranium or other dissolved heavy or rare metals from effluents.

Jan 1, 1989

By R. Q. Honaker

Until recently, the application of the Jameson Cell technology in North America has been restricted to minerals processing. Recently, laboratory, pilot-plant and full-scale testing has been conducted to assess the Jameson Cell's ability to effectively treat fine coal. Based on the data, carrying-capacity relationships have been developed. In addition to its operational simplicity, the Jameson Cell has the ability to provide a separation efficiency near the theoretical separation performance on the basis of ash rejection while achieving a relatively high throughput capacity Tie results obtained from the various fine coal cleaning applications in North America is presented in this publication.

Jan 1, 1999

By Sharon G. Roness

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their: coal. Sulfur was the major concern. Btu content and sodium limited the market for some plants. The PRB market has now extended to plants that are converting from other coals because of the Clean Air Act. These new customers are more sensitive to constituents that affect boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to improve cost controls. Kerr-McGee Coal's Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By Louis W. Cope

INTRODUCTION Various methods for sampling placer deposits have been mentioned by Wojcik in Chapter 2. Here, a brief description and comparison of these methods will be given as related to bulk versus drill sampling. The advantages and disadvantages inherent to each will also be given. The means of sampling can be grouped into bulk or drill samples. As a generality, drill samples over a five-foot length will run from I/,, to 1 /, cubic yard, depending on the diameter of the drive shoe on the drill casing. Bulk samples can be expected to be in the range from one to many cubic yards each. SAMPLE METHODS Bulk Bulldozer-dug trenches and dozer or front-end loader pits are two methods to excavate large bulk samples. Smaller bulk samples can be obtained by digging small dimension shafts through the deposit, by hand or caisson-like drills. It is not recommended to split samples by alternate bucket-loads or by other means, as the effect of a nugget falling into one or the other fraction will seriously alter the sample.

Jan 1, 1992

By John A. Herbst

At the last Comminution Symposium a challenge (Meloy and Williams, 1992) was issued to "predict the typical straight-line, self similar" tumbling mill product size distributions using a population balance model (PBM). Implicit in this challenge is the assumption that the PBM is inadequate for predicting real world grinding performance. This response is presented in three parts: I. Theoretical analysis of the general PBM and its appropriateness for comminution system modeling. II. Examination of the accuracy of prediction of real world milling behavior using linear and nonlinear PBMs. III. Evidence from recent microscale comminution research. This paper concludes with recommendations concerning future research which will: 1. further elucidate mechanisms of particle destruction and creation as well as attrition and 2. increase the accuracy of model predictions in highly nonlinear situations

Jan 1, 1997

By R. Mira, S. Rosa, P. Souza

This paper shows the historical data, local geology and mineralization, the mining methods applied, current production,, the planning staff, the resources of hardware and software available and the computer methods used. The activities are described starting with the driving of ramps/research levels, their dimensional parameters and positioning, driving of production sublevels with the same parameters plus those concerned with the stability of the rock mass during the development and the mining itself. Then, the detailing of the ore body is described together with the stopes planning, the openings stability analysis, and the drilling patterns and explosive types are discussed.

Jan 1, 1998

By Charles A. Ramsey, Kathleen S. Smith, Philip L. Hageman

We developed a statistically based strategy for sampling the surficial material of mine-waste dumps for use in screening and prioritizing historic dumps on abandoned mine lands. This sampling strategy entails the collection of a representative composite sample from individual dumps and allows for regional or watershed-based assessments. One 30-inment dump-composite sample collected using this sampling strategy contains as much information, relative to average value, as 30 individual grab samples at 1/30 of the analytical cost.

Jan 1, 2000

By Armando Z. Remacre

The purpose of this paper is to attest the effectiveness of conditional simulation technique's for determining the principal pre-mining control parameters during mine planning. These parameters include: determining the selective mining unit size, the optimum pre-mining grid spacing and the number of mining faces to be used. The research work was developed in an iron ore deposit located in the Minas Gerais State, Brazil. Phosphorus was considered the master control variable for the research work. This paper provides the structural analysis (variography) , a description of the steps the were taken for setting up the numerical model, the kriging studies which were applied to the numerical model and the final optimum grid spacing, block size and number of mining faces.

Jan 1, 1992

By S. K. Kawatra, M. T. Rusesky, T. C. Eisele, D. X. Zhang

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern US and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effect of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that when the pressure drop is held constant, the d50(c) size decreased approximately linearly with increasing temperature, while the shape of the reduced efficiency curve remained nearly constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1990

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By A. Cavero, M. Diaz

The annual rainfall at Minera Yanacocha's gold mining operations in northern Peru averages 1.2 meters. The influx of water into the operations is higher than losses to evaporation and by ore absorption which results in a positive water balance. To minimize water intake and maintain a balance, some special operating procedures are required, and a system involving diversion ditches, storm ponds, heap skirting and detoxification and treatment of excess water is practiced. An operation background is also reviewed at the beginning of the paper.

Jan 1, 1998