Search Documents

By B. Farshadi, B. Asi, M. J. Habibian

"In this paper, the most significant environmental aspects that are identified in the Taft Copper Project (TCP) are the quality and quantity of water, pollution of the existing watercourses and post-mining land use, matters such as air and noise pollution are deemed to be of less significance. Analysis has been performed for Do Nothing Alternative, Pre-stripping Phase, Mining Phase, Closure and After-use Phases. Analysis of the environmental assessment of TCP was carried out in three stages. In the first stage, the general negative and positive aspects of the project were identified. In the second stage the intensity, magnitude and significance of the environmental impacts of the project were identified. The third stage is related to the final conclusions of the assessment team and the relevant reasoning. A modified Leopold Matrix was adopted for evaluating the significance and magnitude of the environmental impacts. For this project, the matrix was modified to allow the assessor to take account of negative and positive numbers."

Jan 1, 2011

By Stephen H. Hall

INTRODUCTION At some point in the design and development stage of a mineral venture, the assay laboratory building, its interior layout, and major pieces of analytical equipment must be specified for construction or purchase. Even the most experienced chemist would have difficulty in proposing useful specifications without a good deal of investigation into the kinds of analytical tasks that the laboratory will be expected to address, the probable workload, and the operating time constraints. This chapter will provide a logical approach to laboratory design that starts with such an investigation. Specific examples throughout the chapter are drawn from the author's tenure as Chief Chemist at Barrick Mercur Gold Mines, Mercur, Utah, from 1982 to 1985. It is necessary to understand the nature of a modern production laboratory, and to recognize that its operations bear more resemblance to its parent processing plant than to a research, teaching, or custom analytical laboratory. The assay lab is a processing facility unto itself, where samples and reagents are the raw materials, and assay results are the final product. Its most efficient operating mode is as an assembly line, treating samples in a nearly continuous flow. Nevertheless , there are important differences between the lab and the process plant. The products - assays - are individually unknown quantities until they are "produced.' This can vastly complicate quality control compared to the process plant. Capital costs are general 1 y small compared to the plant, but the ratio of operating costs to capital costs for a laboratory is often very much higher than for the plant. This is due to the labor intensive nature of analytical work. For instance, during Fiscal Year 1984 at Barrick Mercur Gold Mines, labor costs for the laboratory staff represented about five percent of the total labor budget, while the laboratory building and equipment represented only about six-tenths of one percent of the original start-up capital. Failure to recognize both the similarities and differences between laboratory and plant operations is the foremost cause of difficulty encountered in designing a laboratory. The

Jan 1, 1986

By S. J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins: including the Emma, Anaconda-Original, Syndicate, Badger-State, and Alice-Rainbow veins, each with strike lengths of over 12,000 feet and vertical continuity in excess of 4,500 feet, along with mining widths from 5 to 50 feet, are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district and eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970’s. Open pit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines. Operations in the Berkeley pit were suspended in mid-1982 because of the rejection of high arsenic, copper concentrates at major smelting facilities throughout the world. Bulk mining of porphyry style mineralization in the Continental pit began in January 1980 to supplement copper production while stripping “C” pushback in the Berkeley pit. The Anaconda Smelter closed in September 1980. A molybdenum circuit was added to the Butte Concentrator in 1981 and mining continued in the Continental pit to produce copper and molybdenum concentrates. A blend of Berkeley and Continental ores were processed to dilute penalty metals in the final concentrates marketed to toll smelters. All mining operations ceased mid-1983 when Anaconda closed the Continental pit and offered the property for sale. Montana Resources reopened the Continental pit in June 1986 to produce copper and molybdenum concentrates. Operations were suspended mid-2000, because of exorbitantly high power prices, but resumed in November 2003 with rising metal prices. Bulk open pit mining of the early porphyry style mineralization has sustained production over the past twenty years and mining is expected to continue in the Continental pit with favorable prices. Future mining will eventually develop a 500 million-ton geologic resource incorporated in a supergene enrichment blanket situated between the Berkeley pit and the Continental pit. Grades in this enrichment blanket range in the neighborhood of 0.5% copper.

Jan 1, 2006

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By C. V. Trang, V. T. Le, K. Enns, J. J. Byerley

The precipitation characteristics of copper and nickel cyanides from solutions continuing copper zinc and nickel cyano complexes are examined. Equilibrium precipitation calculations are presented as well as comparative experimental data. The practical significance of the precipitation data is discussed in the co·ntext of an initial step m an overall treatment strategy for mixed cyanide effluents.

Jan 1, 1998

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By Erhard M. Winkler

The rapid decay and disfiguring of stone monuments in urban and desert rural areas has challenged conservators to protect stone surfaces from premature decay. They attempt to halt the natural process of stone decay and possibly to restore the original strength lost mostly by chemical weathering and the loss of binding cement. Ageneral solution is not possible because the physical and chemical characteristics must be considered for different stone types. The failures of stone preservation and restoration are greater in number than the cures. The need for repair of stone decay goes back to evidence of Roman replacement of decaying stone. The presence of excess water in buildings has long been recognized. Moisture tends to enter masonry from air in humid climates, a most important but often underrated factor (Fig. 1) suggesting that sealing should be the answer. Undesirable staining and efflorescence result in accelerated scaling. Today, the great variety of chemicals available to the modem conservator for sealing. consolidating, or hardening stone fall into two very different categories: surface sealers and penetrating stone consolidants, or a combination of both. SEALERS Sealers develop a tight, impervious skin which prevents access of moisture. Surface sealing has saved monuments from decay by eliminating the access of atmospheric humidity. Pressure tends to develop behind the stone surface by moisture escape. Efflorescence, crystal growth action, and freezing can cause considerable spalling (Anderegg, 1949). Flaking results when moisture is trapped behind the sealed surface. Yellowing and blotchiness are also frequently observed. The following sealants are in common use today: linseed oil, paraffin, silicone, urethane, acrylate, and animal blood on stone and adobe. Extensive cracking and yellowing has resulted soon after application. In the past many such treatments have created more problems than cures: 1. Linseed oil and paraffin have been in use for centuries. Embrittlement and yellowing occur rapidly because these are readily attacked by solar ultraviolet radiation. 2. Animal blood as paint has temporarily waterproofed adobe mud and stone masonry. The origin of blood paint has a religious background rooted in the Phoenician and Hebrew cultures. Instant water soluble dried blood can substitute for fresh blood. Winkler (1956) described the history and technique of the use of blood. 3. Silicones have proven very effective and are long lasting. In contrast, acrylates, urethane, and styrene are generally rapidly attacked by UV radiation (Clark et al., 1975). Sealing of Different Rock Types Granitic rocks have a natural porosity traced to 4.5% contraction of quartz, during cooling of the parent magma, compared with only 2% contraction of all other minerals; protection against the hygric forces may require waterproofing of granite in some in- stances. The Egyptian granite obelisk in London is an example. Soon after its relocation from Egypt to London, Cleopatra's Needle was treated, in 1879, with a mixture of Damar resin and wax dissolved in clear petroleum spirit; surface scaling became evident after half a year of exposure to the humid London atmosphere. The treatment of the ancient granite monument from Egypt has denied access of high relative humidity (RH) in London to the trapped salts inherited from the Egyptian desert and has protected the monument from decay (Burgess and Schaffer, 1952). The sister obelisk set up in Central Park, New York City, has fared less favorably because similar treatment was done too late, only after the salts hydrated and hundreds of kilograms of scalings disfigured the obelisk surface (Winkler, 1980). Surface coating of other common stones may be needed. Crystalline marble absorbs moisture from high RH atmospheres: dilation may ensue when curtain panels bow as the moisture starts to expand during daily heating-cooling cycles. A good sealer may prevent the moisture influx provided that no moisture can enter from the inside of the building. Limestones, dolomites and all carbonate rocks are subject to dissolution attack by rainwater, especially in areas where acid rain prevails (Fig. 2). The interaction of sulfates in the atmosphere with the stone can be halted by waterproofing to avoid the formation of soft and more soluble gypsum. The stone surface attack can be diminished if nearly insoluble Ca-sulfite crusts can form, instead of Ca-sulfate. Replacement of fluorite or barium compounds at the stone surface acts as a hardener, rather than a sealant. Sandstones have generally high porosity and rapid water travel can occur along unexpected routes and from any direction. Any surface sealing may do more damage by scaling and bursting than if the stone is left without treatment. Sealing of sandstones is therefore not advised at any time. Testing the efficiency of sealants: Several authors discuss waterproofing materials, silicones, urethanes, acrylates and stearates, as to their water absorption, spreading rates of water on the treated surface, water vapor transmission, resistance to efflorescence, and general appearance (Clark et al., 1975). De Castro (1983) measured the angle of contact of a microdrop (0.004 cm3) on a stone surface as characteristic of the wettability. Laboratory tests and limited field performance are described by Heiman (1981). The crest of a Gothic sandstone arch, which was sealed with silicone,

Jan 1, 1994

By J. Burrows

The Chamber of Mines of South Africa is an association of major mining corporations, gold mines, coal mines, diamond mines and other metalliferous mines. It looks after those interests of its members which can best be handled on a co-operative basis. The Chamber's activities include the engagement of labour; the negotiations of all labour matters, including minimum wage rates, with recognised trade unions and associations; the carrying out of advanced technological research; representing the industry in dealings with the government and the administration of miners' training colleges and rescue training stations. Subsidiary companies of the Chamber handle matters such as the refining of gold and other metals; the processing and marketing of uranium and the marketing of Krugerrands. The thirty-two gold mines members of the Chamber of Mines of South Africa produce approximately 694 tons of gold per annum. To achieve this they employ 430000 persons and break about 8400 kilotons of rock per month. The working revenue is approximately 4 225 million US dollars per annum and the annual working profit is approximately 2 050 million US dollars. The electric power consumed by the gold mining industry is 1650 MW, about 20% of the total power produced in South Africa, and the annual costs of this power is approximately 200 million US dollars per annum. It is estimated that about 25% of this power is used for ventilation and refrigeration appliances. Thus the annual power costs for ventilation and refrigeration is approximately 50 million US dollars. The gold bearing reef is a narrow tabular deposit situated at varying depths throughout the gold fields. The weighted mean rock breaking depths and, virgin rock temperatures range from 1 700 - 9 000 ft (520 - 2 740 m) and 68 - 113°F (20 - 45°C) respectively. The maximum virgin rock temperature at which mining currently takes place is 130°F (54.5 C). Obviously at such depths and temperatures and with such a large labour force the provision of an acceptable environment is critical and to achieve this 59 000 000 cfm (28 000 m3/s) of air is downcasted during the main shift and 122500 tons (430 MW) of refrigeration are provided. Legislation in South Africa requires that on metalliferous mines when more than 1000 persons are employed underground during any one shift the manager shall appoint one or more ventilation officers. The legal responsibilities of the ventilation officers are concerned mainly with the measurement and control of dust. In practice, this is not the main part of their work and ventilation personnel perform many other duties such as measuring and controlling the distribution of air, checking the performance of fans and cooling plants, planning air and refrigeration requirements and, more recently, measuring and controlling noise and illumination levels. Ventilation personnel are specialists who provide management with advice on all matters relating to the mine environment. At the present time there are 506 persons engaged as ventilation personnel in gold mines and a further 1744 persons are employed in gold mine ventilation departments in a non-technical capacity, for example as construction workers, filter cleaners, fire patrollers, etc.

Jan 1, 1980

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By Stephen B. Castor

The rare earth elements (REE) which include the 15 lanthanide elements (Z = 57 through 71) and yttrium (Z = 39) are so called because the elements were originally isolated in the late 18th and early 19th centuries as oxides from rare minerals. Most REE are not as uncommon in nature as the name implies. Cerium, the most abundant REE (Table 1), comprises more of the earth's crust than copper or lead. Many REE are more common than tin and molyb¬denum, and all but promethium are more common than silver or mercury (Taylor, 1964). Promethium (Z = 61) is best known as an artificial element, but has been reported in very minute quantities in natural materials. Lanthanide elements with low atomic numbers are generally more abundant in the earth's crust than those with high atomic numbers. In addition, lanthanide elements with even atomic numbers are two to seven times more abundant than adjacent lan¬thanides (Table 1) with odd atomic numbers. The lanthanide elements traditionally have been divided into two groups: the light rare earths (LREE), lanthanum through eu¬ropium (Z = 57 through 63); and the heavy rare earths (HREE), gadolinium through lutetium (Z = 64 through 71). Although yttrium is the lightest REE, it is usually grouped with the HREE to which it is chemically and physically similar. The REE are lithophile elements (elements enriched in the earth's crust) that invariably occur together naturally because all are trivalent (except for Ce+4 and Eu+2 in some environments) and have similar ionic radii. Increase in atomic number in the lanthanide group is accompanied by addition of electrons to an inner level rather than the outer shell. Consequently, there is no change in valence with change in atomic number, and the lanthanide elements all fall into the same cell of the periodic table. The chemical and physical differences that do exist within the REE group are caused by small differences in ionic radius, and generally result in segre¬gation of REE into deposits enriched in either light lanthanides or heavy lanthanides plus yttrium. The relative abundance of individual lanthanide elements has been found useful in the modelling of rock-forming processes. Comparisons are generally made using a logarithmic plot of lanthanide abundances normalized to abundances in chondritic (stony) meteorites. The use of this method eliminates the abundance vari¬ation between lanthanides of odd and even atomic number, and allows determination of the extent of fractionation between the lanthanides because such fractionation is not considered to have taken place during chondrite formation. The method is also useful because chondrites are thought to be compositionally similar to the original earth's mantle. Europium anomalies (positive or negative departures of europium from chondrite-normalized plots) have been found to be particularly effective for petrogenetic modelling. REE were originally produced in minor amounts from small deposits in granite pegmatite, the geologic environment in which they were discovered. During the second half of the 19th century and the first half of the 20th century, REE came mainly from placer deposits. With the exception of the most abundant lanthanide el¬ements (cerium, lanthanum, and neodymium), individual REE were not commercially available until the 1940s. Since 1965, most of the world's REE have come from two hard rock deposits: Mountain Pass, United States, and Bayan Obo, China. GEOGRAPHIC DISTRIBUTION OF REE DEPOSITS More than 70% of the world's REE raw materials come from three countries: China, the United States, and Australia. China emerged as a major producer of REE raw materials during the 1980s, while Australian and United States market share decreased dramatically (Fig. 1). Table 2 gives recent annual production figures along with estimated reserves by country, and Fig. 2 shows loca¬tions of significant REE mining. MINERALS THAT CONTAIN REE Although REE comprise significant amounts of many minerals, almost all production has come from less than ten minerals. Table 3 lists minerals that have yielded REE commercially or have po¬tential for production in the future. Extraction from a potentially economic REE resource is strongly dependant on its REE miner¬alogy. Minerals that are easily broken down, such as bastnasite, are more desirable than those that are difficult to dissociate, such as allanite. In general, producing deposits contain REE-bearing min¬erals that are relatively easy to concentrate because of coarse grain size or other attributes. For more thorough discussions of REE¬bearing minerals see Mariano (1989a) and Cesbron (1989).

Jan 1, 1994

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By Merih Celasun

The literature in operations research centered on mineral exploration has been comparatively limited in view of the significant implications of mineral discoveries upon the national economies in general and mineral industries in particular. Much of what has been published is of somewhat unsure academic nature, indicating to a certain extent the scarcity of industrial applications. Mineral exploration activities present quite difficult operational and conceptual problems. The purpose of this paper is to discuss the principal characteristics of decision problems encountered in planning an exploration program, to indicate an optimization approach to a certain class of allocation problems, and to suggest directions for future research effort.

Jan 1, 1962

By Russell A. Fields

Barite (BaS04) is an industrial mineral with hundreds of uses. It is primarily used as a weighting agent in drilling fluids. This use comprised approximately 97% of U.S. barite consumption in 1981. Barite is found in three types of deposits: bedded, residual, and vein. Bedded deposits, because of their relatively large tonnage, have been the principle target of explorationists. Increased demand for barite in the mid to late seventies prompted many companies to significantly expand their efforts in barite exploration. Barite exploration techniques currently range from outcrop walking and geochemical exploration to gravity and seismic surveys.

Jan 1, 1983

By E. D. Attanasi, J. H. DeYoung

Although fraught with problems of completeness and comparability, statistical measures of mineral exploration in the United States point downward for 1985 and 1986. Exploration expenditures in the US domestic and Canadian companies have dropped steadily from a 1981 peak of about $400 million to about $190 million in 1985, according to a recent survey of exploration statistics by the Society of Economic Geologists (SEG). These totals have been adjusted to account for differences in the estimated coverage of exploration activity by each year's SEG survey. This survey is now supported by the US Bureau of Mines and the US Geological Survey (USGS). The drop in current dollar amounts does not take into account the effects of inflation, which would make the decline even more substantial. Metals Economics Group of Boulder, CO reported in its Mine Development Bimonthly that announced exploration budgets for 1986 indicated an even larger drop for the past year. Worldwide expenditures for companies covered by the report dropped from about $800 million to $750 million from 1984 to 1985 and plummeted to about $600 million in 1986. Exploration activity has been declining since about 1981. This has been due in large part to low prices for base and ferrous metals. Exploration budgets of mining subsidiaries of oil companies have plunged as parent companies try to conserve cash in the face of the sharpest decline in oil prices in nearly 40 years. Mining subsidiaries of petroleum firms that were either liquidated or divested recently include Anaconda (Arco), Getty Mining (Texaco), and Cyprus Minerals (Amoco). Exploration expenditures in Canada increased in 1984 in regions where gold is a traditional target. But there was little change in 1985, based on preliminary statistics from a federal government report (Energy, Mines and Resources Mineral Bulletin MR 211, 1986). Claim staking in Canada dropped 23% from 1983 to 1984 and declined slightly in 1985. Diamond drilling increased in 1984 to the record levels of 1980 and 1981. The ratio of exploration to development expenditures in Canada, however, fell from a 1981 peak of 0.9 to about 0.5 in 1984. The report also indicated that, since 1981, there has been a massive write-off of reserves with high production costs. Reserve levels of all major metals were down since 1981. Precious metals exploration accounts for an increasing share of total mineral exploration. For example, the SEG data show that 90% of 1985 US exploration expenses by domestic mining companies were devoted to base and precious metals, compared with only 51% in 1980. The restructuring of the mining industry has been accompanied by a decrease in response to the last two SEG annual surveys, but the trend towards precious metals was already established in earlier years. Trade journal reports suggest that the reduction of long-term interest rates has encouraged the mining industry to make cost-reducing capital investments in existing mines to maintain competitiveness. This is consistent with the observations that metals explorations in 1986 was characterized not by announcements of "grassroots" discoveries, but by on-property exploration on identified mines or prospects. In an effort to cut costs, gold mining companies have been following up on low cost production opportunities in their prospect inventories. Short-term, low risk, heap leach operations that can produce rapid returns on investment have been pursued. Specific exploration projects are covered in the individual state sections of this Annual Review. Even though economic growth continued steadily through 1986, the domestic mining industry has

Jan 5, 1987

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By Tracy T. Morris

The current state of the mining community has made it imperative for operations to reduce costs and increase productivity in order to remain competitive. This has been done in Colorado with the installation of an Outokumpu flash flotation machine for the production of a gold/silver/lead concentrate.

Jan 1, 1987

Introduction The objective of the design and operation of a mine is to make as much money as possible within certain reasonable and responsible constraints. The imposition of constraints on the objective of maximizing profits can result in an optimum mine design. This paper deals with the maximization of profits. Optimization will be discussed in a future paper. In the mining industry, it is generally accepted that the maximum economic recovery is defined by identifying the reserves and the sequence of mining that results in maximum net present value (NPV) or discounted cash flow-rate of return (DCF-ROR), as indicated in Fig. 1 (see Lemieux, 2000). Current parametric analyses techniques, such as varying the mining costs; profit reservation; sales price or metal content, to define pit limits and mining sequence technically referred to single, double or triple parameterization, do not assure that the curve in Fig. 1 will be maximized. In defining the sequence, the first material to be mined should be the first grouping of recoverable mineral that has the highest after-tax unit value and that forms a feasible mining unit. The assumed mining of the first pit should be followed by the assumed mining of the second most profitable and practical pit or pit expansion. If this process of grouping and sequencing is followed until the profitability approaches zero, the general sequence required to extract the maximum economically recoverable reserve is identified. The curve in Fig. I is constructed by calculating the NPV for a series of sequences, each assuming operations are terminated on successively lower profit pits. If the operation ceases on a pit with too high of a profit, opportunity is lost, and the NPV is lower than the maximum. The NPV curve peaks and then starts to decline before the zero-profit pit is assumed mined. This occurs because the money invested in advanced stripping would have produced a greater return if it was invested at the dis¬count rate. The maximum economically recoverable reserve is defined by the pit limit corresponding to the maximum NPV or DCF-ROR. Pit and phase definition The real challenge of reserve definition is identifying the phasing and after-tax profit per ton, so that the curve in Fig. 1 can be plotted. The after-tax profit cannot be properly addressed until after the pits are designed, the production is scheduled and the cash flow is estimated. Throughout the years, many investigators have ad¬dressed this problem. A major thrust of the famous paper in which Lerchs and Grossman (1965) presented their algorithm was to identify a sequence that would produce a result similar to that identified in Fig. 1. Whittle's (1988) four-dimensional analysis is designed to address this issue. The author addressed this same issue in a paper presented to the 1968 Canadian Institute of Mining national convention (Lemieux, 1968). Without a relatively simple methodology to con¬struct the curve in Fig. 1, the number of iterations in a trial-and-error method becomes prohibitively burden-some. The pit designer seeks a simple pit-planning parameter that will serve as a proxy for the after-tax profit per ton used in defining the curve in Fig. 1. The designer's goal is to apply this pit-planning parameter using standard pit-wall location techniques to design a series of pits that will provide a guide to the sequencing. Common techniques used to position pit walls are strip-ratio limits, highwall incremental analysis, floating-cone methods or "maximizer" applications1. Costs, revenues, noncash charges, taxes and profits are usually structured on a unit basis for use in the pit-wall location analysis. Application of the proxy parameter using the pit-design tools should, ideally, result in the definition of pits and sequences that will maximize the curve in Fig. 1. 1 The pit-design tool frequently referred to in the literature as an "optimizer" defines a pit boundary that maximizes the value contained within based on the input parameters and the safe pit-wall angle. The optimization of the pit design involves selection of rate of production, cutoff grade, product quality and other considerations. These considerations constrain the maximization of value. Therefore, pit-design tools that maximize value should be called "maximizers."

Jan 1, 2000

By R. L. Bonomi

Developing a mining venture in a foreign country, particularly in South Africa, can be a real challenge to those involved in the operation. The mining division of Southland Energy Corp. was asked to offer consultative support to the New Union Gold Mine, located in the Giyani District, Transvaal, Republic of South Africa, to aid in their expansion from an approximately 65 tonne per day exploration- exploitation project into a full scale mining operation of 300 tpd by January, 1987 with further expansion to 600 tpd by mid-year. This paper ad- dresses the development of the expansion plans, which are presently being implemented. History. Located in the Northern Transvaal, Republic of South Africa, the New Union Gold Mine is part of what is known as the Klein Letaba gold fields. Gold prospecting in the Klein Letaba gold field area dates back to the earliest years of European prospecting activities in the Transvaal where, reportedly, gold was discovered as early as 1887 (figure 1). The claims com- prising the present New Union Gold Mine have been explored by a number of individuals and relatively small mining groups since the early 1930's. The work done by these entities was aimed at recovering as much gold as possible in the quickest and cheapest manner possible and, as a result, the area was not explored in a systematic fashion. The long-term potential of the area, therefore, was not known until very recently.

Jan 1, 1987