Search Documents

By A. K. Bakshi, K. J. Shoop, Komar S. Kawatra, T. C. Eisele

Slurry rheology can have significant impact on the performance of autogenous grinding circuits. A viscous slurry can act as a cushion and retard impact forces between the media and the ore, which reduces grinding efficiency. On the other hand, a dilute slurry will not be viscous enough to hold slurry in the impact zone of the media, which will lead to inefficient use of impact energy. An unfavorable rheology can also lead to overgrinding or centrifuging of the slurry inside the mill. Slurry rheology also affect classification, with higher viscosity increasing the cut size. In this article, the causes of the rheological effects on autogenous grinding and hydrocyclone classification have been discussed. Both plant and pilot scale data from autogenous grinding have been provided to show the effects of viscosity on specific energy con- sumption and other breakage characteristics of the ore. It is shown that: (1) high viscosity, produced by low temperature and high fines content, significantly increases the specific energy consumption and the production of critical size material in an autogenous mill; (2) In hydrocyclone operation, increasing the viscosity causes the d50(c) size to become coarser.

Jan 1, 1998

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Because of increasing production of fine coal during mining over the past century and because of inefficient fine-coal recovery technologies, a vast reserve of high-quality coal now exists in refuse ponds. A novel finecoal circuit, consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column, was evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,170 kJ/kg with 60% mass yield. Results from the treatment of two refuse pond materials are presented in this paper.

Jan 1, 2002

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population. The Darling Plateau is old, having been formed some 200 million years ago, and its soils are deeply weathered. The parent materials were granite and gneis which have broken down to form lateritic gravels, overlying dense kaolinitic clays. Some 30 million years ago, in the Tertiary period, a sub - tropical climate prevailed. Appropriate conditions of moisture, temperature and drainage led to extensive laterisation. Some of the laterite contains bauxite of mineable quality. Some 1.9 million hectares of the south-west of Western Australia is covered by eucalypt forests. Threequarters of this forest is referred to as "Jarrah

Jan 1, 1984

By David McGregor, Ashoke SenGupta, Jerry Darlington

The stability of bentonite clay suspensions against flocculation in the presence of certain anionic polymers was investigated. These polymers included a purified sodium lignosulfonate, a sodium oxylignosulfonate, a potassium salt of humic acid, and a sodium polyacrylate. The polymers differed from one another in molecular weight as well as in carboxylic, phenolic, and sulfonate group contents. The scope of this study is in evaluating the extent of thinning achievable in a bentonite clay suspension in the presence of these anionic polymers under varying electrolyte concentration, presumably as a result of deflocculation of the clay platelets by the polymers. Under certain conditions of polymer dosage and electrolyte concentration, the lignosulfonate seemed to have flocculated the clay suspension, while the other polymers served fairly well as a deflocculating/dispersing agent. The lignosulfonate, however, showed some deflocculating ability when the electrolyte concentration of the suspending medium (water) was increased by adding sodium chloride to the clay suspension. Among the four polymers tested, the polyacrylate was found to be the most effective in deflocculating clay particles, followed by the humate and the oxylignosulfonate.

Jan 1, 2003

By A. de Ferran

Is the Brazilian gold rush over? Judging from the situation in Brazil over the past few decades, the answer is almost certainly yes. The picture of swarms of Brazilian prospectors or "Garimpeiros" crowding or, more correctly, overcrowding the gold regions of the Amazon jungle using the time-aged empirical approach to gold exploration has finally run its course. There are two fallacies that have lead to a reduction in the discovery of new gold fields in Brazil. The first fallacy is that "Brazil's geology is largely unknown." The extreme depth of weathering and the general lack of understanding of the shield deposits are at the origin of this misconception. The second fallacy is that "Brazilian prospectors (`garimpeiros') are very naive, have very little technical knowledge and can only produce gold at very low recovery rates." This is more of a result of wishful thinking for the purpose of justifying limiting exploration programs than it is a real consideration. In this paper, the author takes a methodical heuristic approach to gold exploration in Brazil and offers this as an alternative to the empirical approach of the garimpeiros.

Jan 1, 1997

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors' simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By Winthrop F. Watts, Robert W. Waytulonis

During the 1980's. the Mine Safety and Health Administration (MSHA) proposed new regulations for the use of diesel equipment in underground coal mines, and the National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen", and that reductions in exposure to exhaust pollutants would reduce excess risk. During the same time, the Bureau of Mines tested new emission control technology to minimize diesel emissions. The objectives of this paper are to discuss the major issues regarding diesel exhaust emissions. especially diesel particulate matter (DPM) , and to highlight emission controls that will be available. DPM is a potential health threat because it is respirable in size and is composed of nonvolatile carbon with adsorbed or condensed compounds. These compounds include potentially mutagenic or carcinogenic hydrocarbons such as polynuclear aromatic hydrocarbons and sulfates. DPM contributes to the degradation of air quality in mines with typical mean concentrations ranging from 0.2 to 1.0 mg/m3. In addition to adequate ventilation, control of DPM can be achieved by implemention of improved work practices, regularly scheduled engine maintenance, and emission controls.

Jan 1, 1991

By T. Ko, K. N. Han, C. S. Park, N. S. Kim, C. Yoon, H. Yoon

Quantitative analysis of Platinum Group Metals from ore samples and industrial materials using Inductively Coupled Plasma-Mass Spectrometer (ICP-MS), Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), Atomic Absorption Spectrometer(AAS), and X-ray Fluorescence (XRF) techniques was conducted and the performance of various techniques was compared. The effects of different matrices in the sample materials were compared and discussed for each analytical technique. The ICP-AES technique exhibited better accuracy than AAS but showed limitations in its application due to strong spectral interference in the presence of common matrix elements such as iron. The ICP-MS showed the lowest detection limit and less spectral interferences than the previous two techniques. The XRF technique was also applied to examine the total amount of PGM from industrial materials. Results from each analytical method on various sources were presented and discussed.

Jan 1, 2003

Mine managers need useful data to support production and maintenance decisions; for example, to evaluate the performance of replacement components. Today, managers rely solely on past experience, supervisors, opinions, and time studies. Our paper describes the concepts and algorithms we are developing for an automatic, intelligent decision support system (IDSS) that will aid managers by reducing and analyzing large amounts of, monitoring system sensor data and report only key production and maintenance information.. IDSS contains a pattern recognition, subsystem (IDSS/PRS) prototype to report graphical trends in traditional time study elements. We are designing. and prototyping a knowledge representation subsystem, using Knowledge Craft Tools, that will learn and adapt to the dynamic mine environment and reason about the recognized patterns using representations of manager's knowledge, equipment, capabilities, and mine layout and operating procedures. This subsystem will reduce, large quantities of time study type information to key issues that interest different managers.

Jan 1, 1989

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By M. B. Díaz Aguado

Traditionally, the practical evaluation of a mining project for a potential investment has been made considering mainly technical aspects. But the concept of sustainable development has introduced significant changes in the factors analyzed to make the final decision. This paper proposes an empirical evaluation of a project considering not only technical, economic and financial parameters, but also associated risks and other intangible aspects, such as political considerations, stability in the legal frame, social factors and environmental issues. The proposed methodology is practical and easy to apply for project management. Among its main advantages, the following could be quoted: using this evaluation two different projects or locations of a same project can be compared, future behaviors could be predicted, the index incorporates a new approach to specific mining projects and this perspective could also be applied to other projects with environmental and social impact, such as civil works or industrial projects.

Jan 1, 2007

By H. Peter Knudsen

Karst hosted lignite deposits are characterized by variable thickness of lignite that was deposited in depressions in the karst topography and by the variable extent and shape of the lignite pods. Since the lignite to be mined will feed a mine mouth generating plant, an extremely important criteria in the mine plan is to assure continuous feed to the plant. The variability in both the extent of the pods and the thickness of the lignite within the pods must be taken into account in any mine design in order to quantify the risk that an area being developed will have enough lignite to feed the plant for the specified period. Indicator kriging was used to create a model of lignite thickness of the deposit. Pod boundaries were determined from the indicator kriging model by two methods. First, contour maps showing the probability that the lignite is above a minimum mining thickness were prepared. Using these maps the mine planning engineer can determine either conservative or optimistic boundaries. The second method recognized that the most costly error that can be made in the mine plan is to run out of lignite. Thus, a loss function was determined from the costs of overestimation and underestimation. Using this function, the probability that minimizes the risks of overestimation versus underestimation was calculated.

Jan 1, 1989

By Maurice Rey

The copper segregation process is designed to concentrate oxidized copper ores or mixed sulfide-oxide copper ores which are refractory to normal and cheaper mineral dressing or leaching processes. Such ores contain copper silicates or highly disseminated copper minerals in a gangue not entirely free from limestone or dolomite. Concentra¬tion by flotation is, under these circumstances, not possible and the acid-consuming constituents do not permit acid leaching. A high temperature treatment at 700-800°C, in the presence of a small amount of sodium chloride and of finely divided carbon, concentrates the copper into easily floated metal by a kind of reducing chloridizing roast. The sulfides, if present, are either oxidized in the heating stage and react like oxides or float with the metallic copper in the flotation step. The ores which have the aforementioned characteristics and which are high grade enough to pay for the treatment are scarce, so that the process has only a limited application. Theory of Copper Segregation Sodium chloride, reacting with water vapor and the acid gangue constituents, produces hydrogen chloride which reacts with the copper minerals. The copper is volatilized as cuprous chloride and immedi¬ately reduced on the coal particles by hydrogen emanating from the volatile matter of the coal and from the water-gas reaction. Hydrogen chloride is

Jan 1, 1985

By J. K. Whyatt

A microcomputer controlled data acquisition system has been developed for automatic monitoring of underground instrumentation from a remote location. The system has been used extensively by Spokane Research Center personnel for monitoring rock instrumentation in shafts, drifts, and stopes in hardrock and coal mines, especially where instrument access is limited. Ruggedness was a major consideration in designing the underground portion of the system and it has performed satisfactorily under extreme environmental conditions, including temperatures to 1100 F, 100% humidity, and falling water. The major advantage of the system is that it multiplexes the data from 16 channels through a single twisted pair cable to the receiver, significantly reducing cabling requirements. This receiving station can be as far as 8,000 ft from the instruments without the addition of line drivers. The receiver maintains a data buffer with the latest scans, which is periodical 1 y accessed by a micro- computer, either locally or through a modem, that automatically records and reduces the data. Utilities allow on-site plotting of data and uploading of data to mainframe computers.

Jan 1, 1986

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By J. Drelich, J. D. Miller

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the preparation of high-quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition for the design of polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed. Based on this review it is clear that several aspects of wetting phenomena at mineral filler surfaces require further systematic study. Specifically, efforts should be made to determine the wetting characteristics of molten polymers at mineral-filler surfaces in greater detail. Also, the effects of mineral-surface contamination (including surface hydration) on wetting and adhesion phenomena need specific investigation. It is expected that an improved fundamental understanding of wetting and adhesion phenomena for polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1996

By Salt Lake City Research Center, D. G. Foot, J. D. McKay

As part of its research program on column flotation, the Bureau of Mines, Salt Lake City Research Center has performed studies on (1) column flotation amenability and comparison with conventional flotation results for over 15 mineral systems, (2) alternative methods for improving column bubble generation systems, (3) mineral behavior within a column, and (4) the effect of changes in column operating parameters on flotation grade and recovery. Based on results from these studies, flotation columns (1) are capable of producing higher grade concentrates in fewer stages than conventional flotation cells at equivalent or increased recoveries, (2) require less retention time than conventional flotation cells, and (3) can be divided into cleaning and collection zones that have characteristic mineral-upgrading-per-foot values. Attempts to improve the column air sparger have led to the development of a superior external bubble generation system, which can (1) achieve increased air holdups. (2) produce bubbles from 400 Um to 4,000 Um average bubble diameter with minimal frother addition, (3) provide superior bubble size control, and (4) be maintained without column shutdown. Efforts are continuing to improve column flotation and transfer successful technology to industry.

Jan 1, 1988

By M. R. Peterson, C. R. Ferguson, T. H. Jeffers

The ability of microorganisms such as yeast, bacteria, and various aquatic flora to sorb metals from dilute aqueous solutions is well documented. Although microorganisms have significant potential in decontaminating waste waters, techniques and equipment suitable for bioassisted decontamination are limited. The Bureau of Mines has investigated the use of microorganisms immobilized in porous polysulfone beads for extracting toxic and heavy metals from dilute waste streams. The minus 8- plus 12-mesh beads were fabricated from high-density poly- sulfone dissolved in dimethylformamide (DMF). Dried, thermally killed yeast, algae, duckweed, xanthan gum, and alginates were blended into the polysulfone-DMF, and spherical beads were formed by injecting the mixture into water. Microscopic analysis revealed microorganisms immobilized within the bead pores. The beads had excellent handling characteristics and were tested in stirred reactors, fixed bed columns, and fluidized bed columns for their ability to remove metal contaminants from several waste waters. The effluents resulting from these waste waters met or exceeded the National Drinking Water Standards for cadmium, copper, manganese, and zinc. Other heavy metal contaminants readily sorbed by the beads included arsenic and mercury. Elution of metal values from the beads was accomplished using dilute nitric acid or sodium carbonate.

Jan 1, 1989