Search Documents

By John J. Reed

The 1945 fire at the Braden (El Teniente) Copper Mine in Chile took 354 lives, and ranks as the most lethal metal mine fire in history. The mine was developed in the wall of a canyon over 900 m (3,000 ft) deep. Principal entrance was through a main haulage adit at the canyon bottom, and up through two internal shafts. Mining was by block caving from the top of the orebody with most of about 900 men on shift working in three production areas. Ore was transferred by gravity to the haulage level through a complex system of ore passes with associated ladderways. Normal mine ventilation was incast through numerous level portals and up- cast through the shafts and raises. The fire was confined to a maintenance shop just inside the portal of the lower production level. Smoke, gases and flammable vapors were drawn into the mine, and a subsequent explosion of the gases destroyed an air door and injected carbon monoxide into the workings. Falling water in a drainage raise near the fire made it downcast, which carried gases down to all the lower levels where they were drawn into the levels and then up connecting raises. Miners attempting to escape by climbing down the ladderways from the production levels were met and killed by the rising gases.

Jan 1, 1989

By Rajiv Hadkar, M. D. McKinley, J. B. Hiskey, B. J. Scheiner, G. W. Warren

Flyash from municipal solid waste incinerators containing roughly 13 to 15% Zn, 2% Pb and 0.2% Cd is an attractive material for simultaneous metal recovery and detoxification. Results have shown that Pb in flyash is present as PbSO4 and PbC12 and that about 70% of the Zn is present in the form of soluble amorphous compounds. Leaching results in a number of acid and basic lixiviants show that acid leaching is clearly more effective than basic leaching which is limited by low solubility of Cd and Zn. Cementation in acid solution with pH < 1 promotes redissolution of the precipitated metal. Successful zinc electrowinning from chloride leaching solutions has also been demonstrated, although Pb2+ and Na+ can be potentially detrimental. The presence of Pb2+ can prevent deposition of metallic Zn, forming zinc oxychloride, ZnC12.4Zn(OH)2, instead. High concentrations of Na+ can also result in precipitation of NaCl. This investigation has shown that hydrometallurgical treatment of MSW flyash through leaching, cementation and electrowinning is a potentially feasible method for simultaneous detoxification and recovery of metal values. Several issues have also been identified which would require further investigation for final process development.

Jan 1, 1993

By J. Girard-Dwyer, J. Johnson, J. Whyatt

The choice of fragmentation method is one of the most fundamental aspects of mine design, and often has a major impact on the safety and economic viability of an operation. Almost exclusively, underground mining operations rely on either mechanical excavation or drill and blast techniques to extract rock. Each of these fragmentation methods has distinct advantages and disadvantages, and each is appropriate, and economic, for different mining conditions. However, the choice of fragmentation method can have a pronounced effect on the amount of damage created in the rock mass surrounding the opening. This paper reviews a number of case studies where both mechanical excavation and traditional drill and blast were used in underground mines. Ground support requirements in the mechanically excavated areas are compared to the support requirements in the blasted sections in order to demonstrate the potential safety and cost benefits of the various fragmentation methods.

Jan 1, 2003

By G. D. Schena

A decision support system for the management of the mineral resources of a developing country has been derived. The system allows the evaluation of the impact of a mineral project in a developing country in the broad context of its economy. The analysis permits the assessment of the overall socio-economic consequences of mineral prospects and allows incorporation in the evaluation of issues that are broader in scope than the pure financial objectives. The system is built around the Leontief framework of economic analysis. The original input-output model, enhanced to incorporate country-specific behaviour is integrated with cost-benefit analysis and shadow pricing. The analysis leads to synthetic measures of profitability at market and shadow prices. These measures are useful to direct the mineral policy of a developing country through the exploitation of those mineral resources which are most likely to bring about economic growth and social advancement.

Jan 1, 1992

By W. Linwood Haden

Fullers earth has been mined since about 1920 in southwest Georgia and the adjoining area of Florida. In 1935, the mineral was named "attapulgite" after the source of a sample near the town of Attapulgus, Decatur County, Georgia. Mining and processing of the clay was described in a 1930 publication1 at a time when petroleum refiners were the major users. In the years since then, the uses and users of attapulgite have multiplied, and both mining methods and processing methods have been changed to optimize the clay for the new uses. A comprehensive review of the properties and applications of attapulgite 2 has been published. Only a brief review will be given here to explain the properties being sought and to show how these properties are optimized by mining and processing practices.

Jan 1, 1972

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young&apos;s moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young&apos;s modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson&apos;s ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By J. B. Zachwieja, P. E. Richardson, G. W. Walker

The electrochemical nature of mineral-collector interactions and their relationship to flotation have been investigated to develop a better understanding of the factors controlling sulfide mineral beneficiation. Spectrophotometric and electrochemical techniques have been used to examine the reactions occurring on electrodes composed of a bed of bornite particles in the presence and absence of potassium ethylxanthate (KEtX) at a pH of 9.2. The combined techniques showed that KEtX sequentially reacts with bornite by (1) a chemisorption reaction forming ca hydrophobic species between --0.4 and -0.2 V (SCE), (2) an electrochemical oxidation reaction forming cuprous xanthate between -- 0.2 V and the xanthate/ dixanthogen redox potential, and (3) oxidation to dixanthogen when the potential exceeds the reversible value for the xanthate/dixanthogen couple. The flotation response of bornite closely parallels spectrophotometric and electrochemical evidence for adsorption of KEtX by the reactions listed above. The degree of surface oxidation resulting from the formation of iron oxides on the surface dictates the flotation response as evidenced by the fact that oxidized bornite floats at more anodic potentials than unoxidized bornite. The strong correlations between the flotation response, degree of oxidation, and potential indicate that chemisorbed xanthate produces a hydrophobic layer sufficient to float unoxidized bornite, but cuprous xanthate and dixanthogen arc required to float oxidized bornite.

Jan 1, 1988

The estimation of local recoveries, such as the local recovered tonnage of ore and its corresponding grade at a given cutoff grade, is an important problem in a selective mining operation. Multigaussian kriging provides a simple solution to this specific problem. The solution is also complete in the sense that local recoveries are estimated together with their estimation variances. It is thus possible to assess confidence limit intervals on the estimated recoveries. Multigaussian kriging has been applied to the Jerritt Canyon deposit in a most realistic situation. The various steps of the estimation procedure are presented in detail and the potential of the method is demonstrated in view of the results. The obtained results show that the estimated recoveries are in good agreement with the actual recoveries and the actual estimation errors are correctly predicted by the estimation variances. Multigaussian kriging thus appears as a useful and fully operationable tool for the mining industry.

Jan 1, 1986

By B. H. Gardner, S. Serata, D. Dickie

Since 1958, the Sifto Salt Division of Domtar, Inc., has operated the Goderich (Ontario) salt mine in Michigan basin bedded halite, with shafts located on Lake Huron&apos;s eastern bank. Initial mining utilized a conventional room and pi1lar pattern. However, roof deterioration developed. Incidence of progressive upward failure of saltback and over1yings ha1ey-do1omite layers intensified with entry aging. Studies were therefore initiated on new mining patterns utilizing the Serata Stress Control Method. Pursuant thereto, three test areas, indicated in the mine plan of Fig. 1, were designed and excavated. Full conversion to Stress Control mining was effected in January, 1983. This paper focusses on the instrumentation work in the third test area. Test Area 3 was designed to validate the excavation geometry of the new stress-controlled main entry system. The testing of that design was accomplished, in part, by comprehensive in situ stress, property, and deformation measurements on the performance of the model main entry section of Test Area 3. The paper describes: (1) the theoretical background of the SPDR/Stress Control Method; (2) specific problems and objectives addressed by the 1983 program of in situ measurements, (3) measurement results; and (4) conclusions drawn therefrom.

Jan 1, 1986

By E. T. Sugar

English China Clays, the world&apos;s largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By Douglas J. Uhren, Gary W. Gilbert

This paper describes the risk elements associated with difficult glacial geology, including boulders, heavy groundwater inflow, and potential running soils all coupled with a potentially corrosive service environment. The matrix workshop for the 168-inchfinished diameter sanitary sewer interceptor tunnel in Columbus, Ohio is assembled with the Design Team and the Owner’s design, operations, and fiscal staff. Corrosion protection alternatives are compared against cost and non-cost parameters with relative risk and weighting factors assigned. The Owner working in cooperation with the Design Team uses the matrix workshop to se

Jan 1, 2001

By Mary C. Jennings, Peter F. Marcus

This paper examines the dynamics of aluminum consumption (all products), scrap recovery and primary aluminum capacity for the Western World through 1995, with particular emphasis on the U.S. aluminum industry. The relationship between the prices of ingot, sheet and extruded products is also explored.

Jan 1, 1986

By G. R. Burman

Gilsonite is a brittle, natural solid bituminous resin, classified as an asphaltite. It is found in near-vertical veins in the Uintah Basin of Eastern Utah. Discovered well over 100 years ago by Samuel Gilson, this unique material has, since its finding, enjoyed a variety of commercial and industrial applications. Early uses for the product included black automotive paint and beer vat linings. Among its many important uses today are additives for oil well drilling fluids and cements, additives for sand castings for the foundry industry, reinforcing agent for asphalt pavements, and dispersing agent for black inks. Gilsonite is mined and processed in Bonanza, Utah, by two companies, American Gilsonite Company (AGC), an operating division of Chevron Resources, and Ziegler Chemical, a privately held company headquartered in New York.

Jan 1, 1990

By Lauro Lacerda

Shotcrete is a highly adaptable and widely used underground construction material at infrastructure and mining projects around the world. In fact, many projects could not have been completed without its utilization. As underground projects became larger the use of mechanized wet-mix spraying gradually replaced manual dry-mix shotcrete applications. This paper details some of the reasons for that and provides information on the equipment and operational factors including safety and productivity required to successfully complete underground shotcrete projects.

Jun 13, 2021

By T. N. Singh, M. M. Singh, R. B. Singh

Fly rock is common when blasting shallow holes and during secondary blasting. Although the required quantity of explosives for secondary blasts is less, noise and fly rock can have an enormous environmental impact. This paper mainly deals with field experiments on blast-design parameters and addresses some precautionary measures that can be taken when pop shooting.

Jan 1, 2000

By Clement K. Chase, Manuel Lastra, George M. Potter

Heap leaching for gold-silver recovery in the western United States has been widely applied. Advantages, disadvantages, and requirements of the method are discussed, as well as heap building, recovery systems, agglomeration applications, and safeguards against freezing. A list and review of current heap leach operations world-wide are presented, together with obvious opportunities for application of this innovative technique in new areas.

Jan 1, 1983

By Ahmed I. A. Salama

This paper describes the development of computer density control for heavy media cyclone circuit at the Coal Research Laboratories of CANMET. The control objective is to reach and maintain the medium density set point in minimum time. A description of the mechanical components and instrumentation are presented. The control strategy and computer software are discussed. Testing and evaluation of the installed system are presented.

Jan 1, 1989

By M. K. Quinn, R. D. Chaffins, A. W. Khair

This paper presents an analysis of the effects of topography on static and dynamic ground movements and severity of damage inflicted on surface structures. A typical site containing varying topographical features (i.e., mountains, hillsides, valleys, and flat bottom land) representing the northern Appalachin region was chosen for the study. Typical subsidence monitoring techniques were employed. Frequent measurements were made as the face advanced.

Jan 1, 1987

By C. Ostrowski, Z. Fajklewicz, K. Jakiel

Results of the application of the micro-gravity method in predicting rock bursts and rock mass deformations are discussed. Research was done in the Daisy black coal mine, Upper Silesia, Poland, during 1979-1980. At that time, microgravity investigations helped increase the safety of coalbed exploitation in progress. During the first stage of exploitation, a mining shock of 107 J energy was predicted in a region where 40 miners worked.

Jan 1, 1987

By Tad S. Golosinski

The paper presents the computing stream of the mining engineering curriculum at he Western Australian School of Mines (WASM), a branch of Curtin University of Technology. Learning to use computers begins during the first semester of the initial year of studies and culminates in the Mine Design Project done during the last semester of study. It covers all areas of computing which are judged to be of importance to the graduate.

Jan 1, 1996