Search Documents

By R. F. Hüttl

World-wide Germany is the leading lignite mining nation. Most of the lignite is produced in opencast operations. However, opencast mining causes enormous impacts on natural ecosystems and even on entire landscapes. The extensive production of lignite particularly in eastern Germany results in large devastated areas, which so far have been reclaimed only to some part. For the restoration of the post-mining area of more than 80,000 ha the major land use option is the reestablishment of forest ecosystems. However, adverse site conditions of the post-mining landscape such as extreme soil acidification and salt concentrations call for specific recultivation practices. Therefore, after the German reunification new reclamation and reforestation concepts have been developed for these brown coal areas of eastern Germany by the Collaborative Research Center (SFB 565) at the Brandenburg University of Technology at Cottbus (Germany). As a case study our comprehensive investigations into forest ecosystem development on terra nova in the Lusatian lignite mining district, south-east of Berlin, will be presented.

Jan 1, 2003

By J. Ragot, D. Maquin, N. Heraud

Acquisition of coherent and representative data about the state of processes remains a major problem of process control. This paper proposes an approach that ensures coherence in measurements on an operational industrial process. The basic technique employed relies on balance equilibration of resource mass flow. An interesting particularity of the set up is the ease with which it can be adapted to check productivity or detect sensor failures. In the case of sensor failure, it suffices to examine the evaluations before and after balance equilibration. The algorithm was tested by means of computer simulation using data from an industrial metallurgical flowsheet.

Jan 1, 1992

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By K. N. Han, K. Peri, Y. Guan

The leaching behavior of gold in ammonical solutions with iodine as an oxidant was investigated using cyclic voltammogram and Tafel polarization. The majority of the experiments were carried out at 75°C, and the results were compared with consideraton given to the equilibrium of the iodine-ammonia system. The distribution of nine iodide-containing species at various pH values in the absence and presence of ammonia were considered at three different temperatures. It was found that, with the introduction of ammonia into the system, the concentration of iodide (I-), iodine (I2) and triiodide (I3-) is increased substantially, which in turn helps the rate of gold dissolution. The apparent activation energy was found to be about 46 kJ/mole, indicating a chemical-controlled mechanism.

Jan 1, 2002

By Ulf Marklund, Stig Markstrom

Pioneering work with pilot scale autogenous grinding started in Boliden 1956. From 1961 to 1991 eleven fully autogenous grinding (AG) circuits have been installed at various concentrators within the Boliden company. A compact two-stage grinding system was de- signed in the beginning of 1970s. The system included a pebble extractor which feed the secondary grinding stage with grinding media. The APC grinding system (Autogenous/Pebble/Crusher) is a further development of the AG concept. A new design of the Boliden pebble extractor together with improved control strategy make the performance of the APC system suitable to almost any ore quality. The Boliden AG concept is probably the most cost efficient grinding system of today.

Jan 1, 1998

By D. W. Horsfall

The different types of processes used in fine coal beneficiation in the Republic of South Africa are listed, together with data giving an indication of their separating efficiencies The two classes of coal, fines and ultra-fines, present in the -0,s m fraction of the run of mine coal are discussed, with special reference to their beneficiation characteristics. Using those properties, together with the data on plant efficiency, case studies are worked out to indicate the advantages and disadvantages of the different processing routes available. The paper closes with an indication of areas where research is required to enable some of the processes to be applied to a greater extent than is presently the case.

Jan 1, 1988

By Joe W. Siefke

The world-class Kramer sodium borate deposit is being developed by modern open pit operations near Boron, California. The deposit is a bedded, lenticular sedimentary sequence of borax and kernite crystals together with claystone. The borates dip south into a structural basin-bounding fault and were formed in the bottom muds of a permanent shallow lake. The lake was fed boron and sodium-rich solutions from a thermal spring source of volcanic origin. In addition to deposit geology, present day geotechnical concerns such as groundwater and slope stability will be discussed.

Jan 1, 1995

By Bernard Amadei, Michael J. Robison

The purpose of this paper is to present the results of 102 mu1tiaxial tests conducted on cubical specimens of Indiana limestone using the mu1tiaxial apparatus available at the University of Colorado at Boulder. These tests include (1) uni-axia1 compression and tension, (2) bi-axial and tri-axial compression, (3) biaxial compression- tension and (4) tri-axial compression-compression- tension. The applicabi1ity of existing failure criteria to predict the strength of the tested materia1 is discussed.

Jan 1, 1986

By J. Reyher, R. Bratton, G. Luttrell, B. Li

"Flotation is regarded as the best available method of upgrading minerals and coal fines. However, its efficiency deteriorates rapidly with decreasing particle size. Further, ultrafine concentrates are difficult to be dewatered economically, forcing companies to discard part of the ultrafine materials to impoundments. To overcome these problems, a new method of separating and simultaneously dewatering ultrafine particles has been developed. Following extensive laboratory-scale test work, the process, known as hydrophobic-hydrophilic separation (HHS), has been tested successfully in continuous operations at proof-of-concept (POC)- and pilot-scale tests. The results show that the HHS process is capable of producing high quality clean coal with high recoveries and low moistures. INTRODUCTION Coal preparation plants are designed with up to four parallel processing circuits for treating coarse (> 12 mm), intermediate (12x1 mm) small (1x0.15 mm), and fine (<0.15 mm) particles. The plus 0.15 mm fractions can be effectively cleaned efficiently with gravity separation methods (Wills, 2006). At present, the only commercially viable option for cleaning the finest fraction is froth flotation (Yoon et al., 1999). In flotation, air is dispersed in the form of small air bubbles in a tank in which coal fines are suspended. The small air bubbles selectively collect the hydrophobic coal particles and float to the surface, forming a froth phase which overflows into a launder. As is well known, ultrafine coal particles of less than 30-50 µm are difficult to be collected by the air bubbles, resulting in low recoveries. Furthermore, fine particle flotation suffers from low carrying capacities and poor selectivity due to entrainment problems. (Bethell et al., 2005; Luttrell et al., 2014). In addition, the froth products containing ultrafine coal are difficult to dewater. Mechanical dewatering in general becomes inefficient with decreasing particle size due to small cake porosity and high surface area, resulting in high moistures (Hucko et al., 1988). The cost often becomes prohibitive with particles of smaller than ~45 µm (Bethell et al., 2005). Moreover, the high-moisture products are difficult to handle and incur high shipping costs and lower thermal efficiencies (Honaker et al., 2013)"

Jan 1, 2016

By R. S. Saunders

Congress, under the Nuclear Waste Policy Act of 1982, as amended, charged the U.S. Department of Energy (DOE) with the responsibility for safe and permanent disposal of high-level radioactive waste in a geologic repository. The waste will consist of spent fuel from commercial nuclear generating plants and reprocessing activities. Under direction of this law DOE is currently evaluating Yucca Mountain in Southern Nevada as the candidate site for a potential high-level radioactive waste repository. Presidential, Congressional and State of Nevada approval are needed for repository construction to proceed after successful completion of site characterization and recommendation of the site to Congress. The DOE will submit a license application to the Nuclear Regulatory Commission (NRC) to construct the geologic repository. Following successful construction DOE will update its license application to operate the repository.

Jan 1, 1993

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By Craig J. Nelsen, David A. Smith

In 1987, LAC Minerals (USA), Inc. conducted a high resolution helicopter electromagnetic (EM) and magnetic geophysical survey on the Ortiz Mine Grant, New Mexico. The primary purpose of this survey was to assist in geologic mapping of a major structural zone, the Tijeras-Canoncito Fault System (TCFS). This structure is a very important ore- controlling feature in the area. Geophysical signatures over known deposits was a secondary goal of the survey, but direct detection of mineralization was not anticipated. The TCFS was revealed to be a complex, branching and anastomosing system of faults which locally form the bounding structures of a graben. The geophysical survey guided subsequent geologic mapping by redirecting field investigations, and geophysically redefining some features which previously had been only partly defined.

Jan 1, 1989

By X. Wen, D. Tao, B. Li

A high effective method using a hammer mill, a column pneumatic separator and an electrostatic separator was studied for recycling copper from waste printed circuit board. The factors influencing the copper liberation degree and following separations were discussed. Two different physical separating methods were compared and discussed. Experiment results show that a well-controlled impact action can produce a satisfactory degree of copper liberation at a relatively coarse particle size. Around 90% copper recovery from printed circuit board for coarse particle size can be achieved by using a combination of electrostatic separation and pneumatic separation.

Jan 1, 2003

By Thomas F. Pedersen, J. Jay McNee, Alan J. Martin

Field sampling was conducted in Lake Junin, Peru in order to assess the post-depositional reactivity of the highly contaminated lake sediments. High resolution profiles of dissolved Fe, Mn, SO42- and H2S across the sediment-water interface illustrate that the organic-rich sediments in the main basin become anoxic within several millimetres of the sediment-water interface. These permanently submerged deposits in the main basin serve as a diffusive sink for dissolved Zn and Cu. Conversely, the periodically unsaturated deposits in shallow areas are characterized by the remobilization of Zn and Cu in the deep acidic (pH < 4) pore waters, resulting in the release of these metals to the overlying water column.

Jan 1, 2000

By John C. Heter

The P.W. Gillibrand Company holds 705 placer and lode claims in the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. These claims contain large tonnages of ilmenite, magnetite and apatite with anomalous quantities of zirconium (zircon), niobium, vanadium and rare earth elements. Stockpiling of heavy mineral concentrates associated with aggregate mining from alluvial pits has occurred since 1984. The limited reserves of material from these alluvial deposits and their relatively low heavy mineral grades caused Gillibrand Company to initiate an extensive drilling and exploration program to develop the hardrock resources of ilmenite, apatite and magnetite.

Jan 1, 1995

By Yeonuk Choi, Patrick R. Taylor, Lyle Cunningham

Laboratory experiments have been performed to evaluate the potential for metal removal and recovery from river bed tailings by ferric chloride leaching. The lead, zinc, silver and other metals in the river bed occur due to the old method of dumping mill tailings into rivers. This was practiced prior to the introduction of tailings impoundments. The effects of the leaching method, leaching time, pulp density, ferric chloride concentration, and leaching temperature on the rates and recoveries of lead, zinc and silver were studied. The effects of pulp density and leaching temperature were significant on the extraction rates of lead, zinc and silver. The lead content in the leached tailing was reduced to 0.023 percent, when using an 353O K leaching temperature and 0.384 g of FeC13/1 g of sample.

Jan 1, 1992

By T. M. Campoy, J. R. Jones

When extending the life of an existing mine in Appalachia, it is common to acquire the adjacent reserves and extend the existing mine into it. The existing mine is often renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may he modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (MVS) that require proper planning and control procedures. This paper presents a study that was carried out for the ventilation system of a newly expanded underground coal mine in the Appalachian region. The process of correcting the ventilation system of the existing mine is discussed. That is followed by a discussion of some of the stages of controlling the expanded system. Numerical data for these steps are also presented.

Jan 1, 1994

By David R. Baughman, John C. Gathje, K. C. Oberg, Gary L. Simmons

Santa Fe Pacific Gold Corp. conducted pressure-oxidation pilot plant studies on refractory carbonaceous gold ores from the Twin Creeks Mine in Nevada. The tests were conducted at Hazen Research Inc., Golden, CO, during 1993 and 1994. Laboratory investigations using CIL cyanidation after batch pressure oxidation demonstrated gold recoveries of 90% to 95%. However, pilot plant testing showed that several of the same ore types responded very poorly, with gold extractions of only 45% to 75%. Plant testing was suspended for approximately four months while extensive research was conducted to determine why these ores responded poorly and to identify potential solutions. This paper describes the batch and pilot plant test results, the extensive research activities that eventually identified the cause of the gold recovery problem and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions. Final pilot plant results showed gold recoveries that were consistently greater than 90%.

Jan 1, 1999