Search Documents

By Stefano Colombelli, Nicola Bona, Gabriele Eccher, Luca Schiavinato, Paolo Cucino, Domenico Nave

"BIM technologies provide tools and processes to effectively support the entire life of an infrastructure, from strategic planning to maintenance. As a consequence, infrastructure design processes currently make frequent use of BIM tools. This paper describes the BIM oriented design of the underground railway extension in the metropolitan area of Catania. The paper highlights the design process and the chosen BIM tools considering the boundary conditions characterizing the project, i.e. basic information missing in the final design project, need of coordination between different design disciplines and designer companies, and, finally, need for a flexible design approach able to adapt to changes occurring during design development. INTRODUCTION The underground railway extension in the metropolitan area of Catania is composed of two lots of approximately two km each, namely “Stesicoro-Aeroporto” and “Nesima –Misterbianco”. Works to be realized are: •,Main tunnel: mechanized tunneling using a TBM-EPB machine, for the entire length of the lot; •,Underground stations: San Domenico, Vittorio Emanuele and Palestro, conventionally excavated as enlargement of the TBM tunnel after the partial demolition of precast segments; •,Ventilation and emergency shafts: connecting seven tunnel levels to road level on Stesicoro-Areaposto lot, six on Nesima-Misterbianco lot; •,Additional structures such as technical rooms and parking lot; •,Electric Substation at Monte Po' stop; •,Temporary works: TBM launching and arrival pit to be dismantled at the end of the works."

Jan 1, 2016

By Rainer Alles, Markus Keller

INTRODUCTION For overland conveyors of several kilometres length and as well as wide for conveyors designed for high mass flows, the cost for the conveyor belting share is 40% to 50% of the invested cost 173. The German Standard DIN 22101 is used for calculation and dimensioning of - conveyor belts and belt conveyor components. Developments in rubber technology and conveyor belt design required a revision of the standard released in 1982 121, which was published in August 2001 131. New research results and publications 16-9, 13-15] led to a better understanding of the material behaviour and their influences on conveyor belts. Test and calculation methods have been established to determine the most important parameters which are related to the performance of a conveyor belt line. These parameters are • The running resistance of the idlers • The indentation resistance of the belt • The dynamic splice efficiency • The distribution of belt load in the splices, transition zones and on pulleys. As a result, new rubber compounds with low indentation losses allow the use of reduced friction coefficients and thus lead to reduced power consumption, smaller drives and lower belt tensions. The deeper understanding of the flux of forces within belt splices led to both optimised splice design and optimised rubber compounds which significantly improve the dynamic splice efficiency. Therefore, in accordance with the standard, the benefits of these technologies and the better understanding of material behaviour allow a reduction of belt strength still maintaining sufficient safety factors. Thus engineers are enabled to calculate belt tensions more exactly and users are encouraged to pay more attention to starting and braking techniques. DETERMINATION OF DRIVE FORCE According to the DIN standards the resistance to motion generally has to be determined for each different section of the belt conveyor including upper and lower run separately. The necessary drive power P is calculated as [ ] with v as the conveying speed. The total of all resistances to motion of carry and return run can be determined as [ ] FHo and FHu are the primary resistances consisting of the running resistances of the idlers, the indentation resistance of the belt, the fulling of the conveyed material and the flexure of the belt. While indentation resistance and idler resistance are measurable, they have been deter- mined to be responsible for up to 70% of the primary resistances covered by FH. Further FN is the secondary resistance that covers, for example, the resistance of feeding points and scrapers. Fa are the total slope resistances and Fs is the total of all special resistances, resulting, for example, from belt steering devices. These three resistances should be neglected in the following discussion. For conveyors where a determination of the substantial parts of the resistances to motion is not possible, according to the new DIN standard [31 a determination of the drive power is acceptable by using the fictitious friction factor) [ ] In this formula the index i identifies the individual section of the conveyor, 1 is the length of the section and MR, MG and ML are the related masses of the idlers, the belt and the load in kg/m. The fictitious friction factor f determines the ratio between the overall resistance to motion and the total of moved masses within the

Jan 1, 2004

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By Thomas D. Kaufmann, Robert C. Drury

Few factors are as important as fluctuations in aggregate economic activity and exchange rates in determining the profitability of mineral investments. Macroeconamic theory explains how the two factors are interconnected in today's world and in tomorrow's. We can use macro¬economic theory to lessen some of the risks in mineral investments. And in the current state of the world the risks are high. The above paragraph summarizes our argument. Our goal in this paper is to examine the nature of contemporary business cycles so as to explain their implications for the metal industries, particularly the implications for capacity. Thus, our first section examines the workings, causes, and history of the recent economic fluc¬tuations. In doing so we must understand how current world economy is interconnected, that is, how economic events in one country are trans¬mitted to the rest of the world. Our view is that governments and central banks are key actors in the creating of economic fluctuations. Then, in section two, we work out the implications of section one for the metal industries focussing on comparative advantage, trade, and capacity decisions. Over the last fifteen years the world economic system has had slow overall economic growth and has had strangely unpleasant recessions. While future business cycle will not repeat the de¬tailed pattern we have seen, there will be similarities. The similarities need to be under¬stood before investment occurs. The slow growth in the world economy since the early 1970s has aggravated the problems from business cycles, created its own problems, and has partially hidden the effects of other events. Major realignments of currencies are likely to take place over a business cycle. The nature of the causes of the cycle will determine the direc¬tion of change in the exchange rates. For example, whether a USA recession will be accompanied by a weaker or a stronger dollar will be determined by the cause of the recession. The realignment of currencies over a business cycle leads to a realignment of comparative advantage in the metal industries. Thus, not only will world metal consumption vary over the business cycle but the impact on various countries' metals industries will differ consi¬derably. Competitiveness often depends more on the value of the dollar than it does on inherent efficiency and wage rates. Capacity decisions are inherently riskier due to the country specific nature of exchange rate risk. A realignment of currencies changes the pattern of trade if and only if the country with the cheaper currency also has idle capacity. The importance of our topic is indicated by Table 1 which shows the impact of cyclical and exchange rate shocks on the USA metal industry. In the cyclical downturn, from the peak of 1979 to the trough of 1982, consumption dropped by a fifth to a third. Metal price moved in the same

Jan 1, 1989

By A. Sinha, C. Sawmliana, P. Pal Roy

Using the newly developed and permitted explosive Pentadyne-HP (Gulf Oil Corporation Ltd., Hyderabad), the Blasting Department of the Central Institute of Mining and Fuel Research, Dhanbad experimented at the GDK-5 Incline, RG-1 Area of the Singareni Collieries Company Ltd. (SCCL) to establish one modified angular cut blasting pattern as an alternative to conventional solid blasting in India to obtain longer pull, as well as to achieve at least 40 t of coal in a single blast round for the deployment of diesel load-haul-dump units at the face. This permitted explosive satisfied the statutory requirements of incendivity characteristics applicable to P5 explosives of the regulatory agency Directorate General of Mines Safety (DGMS) of India. The present paper summarizes the development of this new blasting pattern and its possible use in Indian coal mines.

Jan 1, 2010

By R. Kneisley, D. Conover, K. Haramy, K. Hanna

INTRODUCTION Coal mine entry intersections are high-risk areas for roof falls due to inherently wide roof spans, excessive stress, and variable intersection shapes resulting from breakthrough misalignments. Statistics from underground coal mines reveal that a high percentage of injuries occurs from roof and rib falls in entry intersections (Peng, 1980). The U.S. Department of the Interior, Bureau of Mines, is conducting a field research project to investigate failure modes surrounding underground coal mine entry intersections. The research objectives are to (1) develop a method to determine failure modes and stress-displacement relations around coal mine intersections and (2) develop engineering guidelines and empirical relationships for use in designing safer coal mine entry intersections. The basic approach to achieve the objectives is to instrument and monitor intersections before, during, and after intersection development in order to determine contributing parameters, such as in situ stresses, stress changes, strata movement, geology, physical properties, and mining sequence, that may influence the short- and long-term stability of the intersection and adjacent entries. This paper describes a rock mechanics instrumentation program, data analyses, and a comparison of two case studies conducted at two underground mines, designated as "A" and "B", in the Illinois Coal Basin. The instrumentation plans and data collected during development and long-term monitoring of four-way intersections and adjoining entries are presented. Data analyses of pre- and post-mining roof stress, pillar loading, strata movement, roof bolt loading, and geologic features are included. INTERSECTION FAILURE MECHANISM The region surrounding an entry intersection is characterized by different failure criteria than the region surrounding a single entry. Stresses induced during intersection development may result in a high incidence of roof and rib failures. Various numerical modeling techniques have been used to evaluate the failure modes surrounding intersections (Gercek, 1982; Chugh et al., 1975). Numerical modeling techniques include problems associated with the analysis of post-failure behavior, provision for different horizontal stresses (i.e., 01 f 021, and determination of inputs required for any non-elastic behavior. It seems likely that more sophisticated failure criteria, based on actual field data, are needed. The Bureau of Mines has conducted an extensive instrumentation program to investigate actual intersection failure mechanisms and to provide an improved understanding of stresses and deflections using beam and plate theories. Beam theory is not applicable to analyzing intersections (Wright et al., 1964); however, it can be used to explain roof deflection and failure (shear and flexure) of adjacent entries and to provide an improved understanding of stress changes and displacements as the entries, crosscuts, and intersection are developed (Hanna et al., 1985). Beam theory may be used for entries when the roof length is twice the width. When the length is less than twice the width (as in intersections), the roof must be analyzed as a three-dimensional problem, and stress and deflection calculations are based on flat plate theory (Adler and Sun, 1976). The confined-core theory (Wilson, 1972) hypothesizes that within a typical pillar, two regions exist: a confined-core region where the horizontal confining pressure is uniform and approximately equal to the overburden pressure, and a yield zone where the vertical pressure increases from nearly zero at the rib to a pressure peak at the boundary of the yield zone. The strength of coal in the yield zone ranges from nearly zero at the rib to nearly full strength at the confined core. The vertical stress in the confined core decreases from maximum at the yield zone boundary to the overburden pressure some distance into the pillar. Excavation of the adjoining entries

Jan 1, 1986

By Jan Visman, James W. Parkinson

GENERAL INTRODUCTION Sample collection, preparation and analysis are all steps in a single process designed to provide information about a much larger amount of material than the sample itself. For example, information about the ash content of a unit train load of coal may be derived from a single, relatively small sample of perhaps a few hundred pounds (liters) extracted from the entire shipment. These three steps can be thought of as links in a chain, allowing the simple analogy that the strength of the chain, or, in other words, the value of the information is only as strong as the weakest link. Sample collection, discussed in Part 1 of this chapter, is critical because analytical procedures can do no more than reveal the characteristics of the sample presented to the laboratory. If that sample does not properly represent the population to be characterized, neither will the analysis of that sample. Sample preparation is also a critical part of the chain. Any change in the nature of a sample between the time it is collected and the time it is analyzed will appear to reflect the nature of the population. For example, sample preparation procedures that allow air to partially dry the coal sample before reaching the laboratory will cause the sample analysis to indicate a lower moisture content than the sample originally had. Other changes can be more subtle. Second only to moisture loss, oxidation reactions generally cause the greatest problems. Oxidation of a coal sample can alter surface properties, changing flotation response. In extreme cases, combustion parameters, such as caking or agglomerating properties or mineral composition, such as pyrite content, can change. Water samples can also be altered by oxidation. For example, ferrous iron can oxidize to ferric iron, possibly changing water quality parameters such as pH. Sample analysis, the subject of Part 2 of this chapter, is the final link in the chain. Obviously, no laboratory procedure can correct for problems created by improper sample collection and preparation. At the same time, poor analytical techniques will create incorrect information about the total amount of coal from which the sample was extracted (the population) in the same manner as improper sample collection and preparation. The key to gaining correct information about the population is to view these three steps as parts of a single process. Following proper techniques through only one or two steps of the process will not produce accurate information.

Jan 1, 1991

By Eric W. Johnson

In the late 1950's a low-grade copper ore zone was outlined at the fifty-year-old McIntyre Porcupine Mine in Northern Ontario. Following this an independent copper circuit was installed in the existing gold mill. The nature of the operation decreed that capital expenditure be a minimum. To this end, in order to resolve the problem of storing and grinding two separate ores, it was decided to install a divider in the existing 4000 ton capacity fine ore storage bin and to replace ten conventional feeders with sixteen Mexican feeders. The article describes a successful application of the Mexican type feeder.

Jan 1, 1968

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By Fred L. Myers

The use of finite element programs for evaluating large grinding mill shells is becoming increasingly popular. However, large scale, detailed analysis can become a burdensome task when one is required to manually prepare the necessary data to be entered into the program, while evaluating the voluminous results is even more devastating. Although available computerized finite element analyses can reduce computation time from years to months or even weeks, additional pre and post processors can reduce the time for data preparation and result evaluation to hours, while simultaneously reducing the probability of human error. Examples of the uses of these processors are presented as well as typical modeling techniques.

Jan 1, 1979

By Jacques B. Wertz

Although fracture intersections and "domes" seem at a number of places to be the basic structural combination for the occurrence of a mining district, of the porphyry-copper type particularly, this situation is, of course, not always to be expected. For instance, the group of mines comprising Superior, Ray, Miami, Globe, Christmas appeared from the beginning of these structural studies as typical exceptions, and there are others. One had to expect additional parameters to allow for any mineral concentration to occur. One of these apparent parameters is here considered. From the result of stratigraphic studies related to ancient formations in Southeast Arizona, the Martin limestone (Devonian in age) was retained as having a possible relationship with the structure-economic studies in progress, as evidenced for instance by the mineralized O'Carroll bed located at the base of the Martin. This limestone formation has been rather extensively investigated in the past and there are many known sample localities. For this work, the isopach map was drawn by computer to insure more objectivity and, in addition to the available data points, a number of dummy points with a zero value were added around the assumed form-

Jan 1, 1971

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By Young C. Kim

Because of the high cost of obtaining coal washability samples, it has been difficult to obtain washability variograms in the past. As a result. It could not be determined if geostatistical prediction tool known as kriging can be applied to predict in-situ coal washability characteristics.

Jan 1, 1988

By S. Mohanta, S. Chakraborty, B. C. Meikap

"An air dense medium fluidized bed separator is an efficient dry process for the removal of undesirable gangue material from run-of-mine coal. Its cleaning performance depends on a variety of operating parameters that are interrelated in unknown, complex ways. A literature review showed that these parameters' effects had been experimentally investigated using a traditional one-variable-at-a-time approach, which is highly inefficient and sometimes misleading because many of the parameters often interact with each other to alter the overall equipment performance. Also, it is realized that the interrelationship among these parameters can have a significant effect on equipment performance. Therefore, to correctly evaluate the effects of individual parameters as well as their interactional effects on the separation performance of an air dense medium fluidized bed, we conducted a scientific study based on response surface methodology. Empirical models for two key response variables, namely, product ash and combustible recovery, were developed and subsequently used for identifying an appropriate operating region to achieve optimum separation performance. Furthermore, the optimum performances predicted from the empirical models were validated against experimental data. Preliminary results show a strong interaction among the operating parameters investigated in this test program.IntroductionFluidization is widely applied in industry for its various useful features. In the coal industry, it is used in the air dense medium fluidized bed (ADMFB) separator for the beneficiation of run-of-mine coal. In this separator, a medium is created by suspending fine magnetite particles in an upward air flow, and this pseudo-fluid is used as the beneficiation medium, with the lighter coal particles floating to the medium’s surface while heavier particles sink to the bottom. This separation technique had been receiving a significant amount of attention worldwide in recent times for its specific advantages of low operating cost and less restriction for small capacities (Luo and Chen, 2001; Sahu et al., 2009; Dwari and Hanumantha Rao, 2007; Van Houwelingen and de Jong, 2004), but it is still not a well-established industrial practice because of the availability of efficient wet processing technology. However, with a revival of interest in the dry beneficiation of coal, in general, and ADMFB, in particular, there is once again a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have been made to make this process a competitive and viable option. The existing literature reveals that most of these research efforts had been essentially focused on the identification of a single parameter that has a key influence on separation performance, without taking notice of parameter interactional effect. For example, Luo et al. (2004) proposed a pressure drop number to distinguish separation performance without considering the bed height and gas velocity, which are intimately related to this proposed pressure drop number."

Jan 1, 2015

By R. Vogt, H. C. Mult, F. L. Wilke

INTRODUCTION At present, the capability of production planning software based on Linear Programming (LP) is still limited to the optimization of the single LP-run. This is due to the LP-model itself which cannot consider the interdependencies between individual LP- runs. With regard to planning of selective mining this limited way of optimization frequently leads to situations, where the remaining and accessible ore blocks do no longer allow to produce ROM-ore in the qualitative composition required by the ore processing plant. However, many of the aspects taken into consideration when setting up production plans built from mutually dependent LP-runs cannot be modelled in a system of linear equations. They are thus unsuited for treatment with LP and have to be taken care of by the planning engineer without any assistance by the system. The KBS currently under development is intended to assist the planning engineer in designing a production plan under special consideration of the combination of consecutive LP-runs and blending beds. It is not necessarily intended to find the optimum solution within a given planning situation which is, anyway, hard to determine due to the multitude of influences. The objective is rather to work out a good and - from the practical point of view - feasible production plan. The new aspect with respect to mine planning is the integration of expert knowledge and experiences via the KBS into the planning process in order to support the planning engineer. The planning system is being developed in close cooperation with an iron-ore open pit mine. COMPONENTS OF THE PLANNING SYSTEM The software is being developed on a workstation under UNIX and comprises the components LP, CAD-module and the KBS. The applied multi-goal LP-algorithm is an in-house development of the Department of Mining Engineering at Technical University Berlin. It was already successfully implemented within other mine planning programmes and was only slightly adapted to the specific needs of the present system. Within individual LP- runs it finds the optimum qualitative composition of ore production in the sense of the selected optimizing criterion and under the given restrictions: i.e. it determines tonnages to be mined from blocks in order to optimally meet the requirements of the ore pro- cessing plant. A CAD-module based on the commercial SURPAC package in combination with a simulation device is used to graphically depict the block model and progress of mining. Both LP-algorithm and CAD-package are integrated in the KBS. It has been decided to use the shell NEXPERT OBJECT as it is a hybrid system which supports both rule-based and object-oriented knowledge representation. MINE-MODEL AND LP-MODEL KBS have to be tailor-made for specific planning problems. Therefore, it had to be decided which specifications of the iron-ore mine should be represented in the model. As the limited possibilities of a university institute do not allow to develop a KBS for mine planning which is ready to use in industry, it was decided to concentrate on those characteristics that can be regarded as typical for iron-ore surface mines and that seemed to be suited for treatment with knowledge-based techniques. The following chapter summarizes the most important features of the mine model. The description of the requirements to the mine's sales products is followed by an outline of the applied LP-model. Mine model • The model of the mine as it is used for planning consists of • the block model of the deposit, • the mobile equipment, • stockpiles and blending bed and • the requirements to the sales products. The deposit is described by a block model which contains data on the chemical composition, LOI, grain size and tonnages. Grain size was included as it is important for the two sales products of the mine. Furthermore, it is known whichs blocks require and which don't require blasting; this is relevant to the assignment of loading equipment to individual blocks. The blocks are devided in three categories: • ore, which will directly be taken to the blending bed; • waste, which will be put on the waste dump; and • blocks which will be either transported to the blending bed, to stockpiles or to the waste dump depending on the specific planning situation. This decision is made during planning. Neighboring blocks are combined in mining areas to which the loading equipment is individually assigned. Mobile equipment comprises shovels and wheel-loaders as well as trucks. The characteristics of the loading equipment are important for their ability to load different blocks and for the permissible degree of their re-positioning etc. The mine disposes of a blending bed for homogenization of the production, of a waste dump, and of several stockpiles with different ore qualities. The requirement to make only limited use of the stockpiles for economic reasons is included in the KBS. According to long term planning two commercial products have to be produced, which differ both in grain size and qualitative composition (TABLE 1). Their mass-proportions in the blending bed have to be within a fixed range. Not considered in long term planning is the occasional need for lump ore, which occurs at very short notice and has to be produced in a "campaign-like" manner. This requires the total re-arrangement of all plans for on- coming blending beds and would therefore be ideally suited for

Jan 1, 1996

By James P. Connell

HISTORICAL BACKGROUND The American Concrete Institute defines shotcrete as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity onto a surface." This definition thus includes what is traditionally known as gunite, which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this chapter. In 1914, following the invention of the mortar gun in 1907, then chief engineer of the US Bureau of Mines (USBM) George Rice developed the gunite process for underground test work at the USBM facility at Bruceton, PA. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto tunnel in California. The greatest development was in Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Initially, shotcrete was used to reduce manpower requirements for forming and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately after the opening had been made. The incorporation of wire mesh into the shotcrete led to the new Austrian tunnel method or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the US reliance on wood or steel supports in main-line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to accept the new and seemingly unrealistic lighter shotcrete support. APPLICATION REQUIREMENTS Shotcrete is a relatively new material for use in underground support systems. Consequently, experienced miners are not always available who are capable of applying the material effectively. Shotcrete, particularly in the small cross sections typical of mine shafts or haulageways, is applied in cramped quarters under less than ideal conditions. Adequate lighting should be made available. The surface should be clean and free of running or dripping water. It may be necessary to collect flowing water in plastic pipes or water collection devices. Any dry cement dust from previous shotcrete applications should be washed from the surface in order to assure a good bond. The US Bureau of Reclamation (USBR) while shooting test panels at the Cunningham tunnel in 1974, found that experienced shotcrete operators were able to obtain up to three times greater compressive strengths than were obtained by unskilled operators using the same equipment and shotcrete mix. ENVIRONMENTAL AND SAFETY REQUIREMENTS Since sodium and potassium hydroxide, as well as other moderately toxic compounds, are often contained in shotcrete (particularly where accelerators are used), safety precautions must be taken to prevent skin and respiratory irritation. Nozzlemen and helpers are required to wear gloves, protective clothing, and ventilation hoods with a filtered air supply. Respirators approved by USBM, equipped with chemical filters that will not pass the caustic mists, may be permitted in lieu of hoods if goggles or safety glasses are worn. Protective ointments are available to reduce skin irritation. All air and shotcrete feed hoses should be equipped with safety-type couplings and secured with safety chains at each coupling to prevent whipping in the event of a hose or coupling failure. Some environmental effects can take place down-stream from the development face being supported. The accelerator compounds, as well as the portland cement used in the shotcrete, will be found in the rebound material which falls to the invert of the heading. Since these compounds may be leached from the rebound material and carried by the drainage system, it may be necessary to install neutralizing or other water treatment facilities. Investigations may find that the final reaction with other compounds being leached from the mining operations may result in a more or less environmentally acceptable end product. USES OF SHOTCRETE General Uses Shotcrete, as a combination of cement, aggregate, and accelerator, is utilized for underground openings such as shafts, adits, haulageways, and service chambers for the following general purposes : (1) primary sup¬port; (2) final lining; (3) protective covering for excavated surfaces that are altered when exposed to air (the protective covering may be of a temporary or final nature); (4) protective covering for steel or wooden supports, rockbolts and rockbolt plates, heads, nuts, and other mats, including wire fabric, used to prevent rock-falls; and (5) as a lagging material in place of timber, steel, or concrete between steel or wooden supports. These applications can be grouped into three general use categories: shotcrete used as a rock sealant, shotcrete used as a safety measure, and shotcrete used as a structural support. Use as a Rock Sealant Thin applications of shotcrete can reduce or prevent slaking of shales or other rocks that are altered when exposed to the wetting and drying cycles created by mine ventilation circuits. While shotcrete may be effective in preventing such rock alteration, at the present time it is not as economical or efficient as other commercial sealants. However, if the sealant property can be incorporated into the structural support capability, the added contribution is usually helpful. Thin applications are not usually sufficient if the alteration of the

Jan 1, 1982

By W. W. Bristol

The Jerritt Canyon Joint Venture project is located approximately 50 miles (80 km) north of Elko. Nevada, U.S.A. and produces between 250 and 300 thousand ounces of gold annually. The Joint Venture is 70% owned by Independence Mining Company and 30% owned by Meridian Gold Company. Independence Mining Company is the operator. The Jerrin Canyon Joint Venture started operations in 1980 mining a series of open pit mines. Since the early 1990's, the discovery of deeper ores has required the joint venture to develop and mine a significant portion of its annual production utilizing underground mining methods. Underground production started with the West Generator Mine in 1993 followed by the Murray Mine in late 1994. Presently, two additional underground projects are being developed. Underground mining at Jerritt Canyon is budgeted to produce 128 thousand ounces in 1997. This paper documents the major transition/redevelopment of the Jerritt Canyon mining methods.

Jan 1, 1997

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By Larry Sevenker

On the basis of favorable salt characteristics, primarily compressive strength and impermeability, solution-mined cavities can provide structurally stable isolation chambers for waste. Solution mining techniques are established for storage of hydrocarbons. The proposition of waste isolation in engineered salt cavities is similar to this practice relative to characterization, certification and safeguards. What materials are isolated and how operations are conducted are principle differences. Compatibility of wastes with other wastes must be considered, but hazards can be precluded by avoiding certain mixtures. Waste material characteristics and cavity considerations are discussed.

Jan 1, 1981