Search Documents

By B. K. Mishra, R. K. Rajamani

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills. DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important, factors, such as the configuration of the liner and the geometry of the lifting surfaces, are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill, with particular emphasis on large diameter mills.

Jan 1, 1994

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By Pascale St-Germain, Michael Li, Lionel J. J. Catalan

The oxygen flux into water-covered reactive sulphidic tailings is required for evaluating the long-term performance and predicting the quality of engineered shallow water covers. This information can also serve as an input to the design of water covers for reactive tailings decommissioning. This paper describes some dissolved oxygen (DO) profiles recently measured in the field across the tailings/water interface and oxygen fluxes derived from these profiles. These fluxes are compared with previously reported flux values from similar field measurements. Techniques and pitfalls for measuring DO profiles and calculating oxygen fluxes are also discussed.

Jan 1, 2000

By Ted D. Maki, Joseph B. Taylor

INTRODUCTION FMC's Paradise Peak mine, located 13 Ian (8 miles) south of Gabbs, Nevada, became opera¬tional in April of 1986 (Figure 1). It was designed and built by Davy McKee, who was instrumental in equipment design and selection. It is the 7th largest gold deposit in the United States with defined reserves of 10.9 mt (12 million st) containing 34 million gms (1.1 million tr oz) of recoverable gold and 933 million gms (30 million tr oz) of recoverable silver. The mine extracts ore by the open-pit method, taking advantage of a 1.5:1 stripping ratio. The mill operates at a 3600 mt/day (4000 st/d) capacity. Crushing is done in three stages to achieve an ore size of minus 0.635 cm (0.25 inches). Grinding further reduces the ore to 85% minus 100 mesh. The ground ore is treated with cyanide in agitated leach tanks and then washed in the counter-current decantation (OCD) thickeners. Zinc is added to the clarified, deaerated pregnant solution to precipitate the precious metals. The precipitate is acid digested to eliminate excess zinc, filtered and retorted to drive off contained mercury. The retorted precipitate is then fluxed, melted and poured through cascade molds. Dore bars are cleaned for shipment and the slag is sent to an in-house slag treatment system. ELECTROSTATIC SEPARATION The dry electrostatic slag treatment system at Paradise Peak is the first installation of its kind. Electrostatic separation has been widely used in mineral processing since the early 1950's. A brief discussion of the theory behind the process is helpful to those not familiar to electrostatic separation. Charging and sepa¬rating slags, dry minerals or other materials by ion bombardment is the most common form of electrostatic separation. Millions of tonnes of minerals are processed each year by this method. In an ion bombardment separation, granular material is fed onto a grounded metal cylinder (or roll) and charged by a corona-producing electrode placed above the roll's surface (Figure 2). While both conductors and non¬conductors become charged, only the conductor is able to lose its charge. The charged non¬conductor, as it rests on the roll's surface, "sees" an oppositely charged image of itself in the metal surface. It is attracted to the image charge, becomes electrostatically pinned to, and moves with the roll's surface. The conductive particle also sees an image and is attracted to it. But upon touching the roll's surface, it discharges rapidly to the grounded surface and is thrown free from the roll's surface with a projectile motion. In the case of precious metal slags, the con¬ductive particles would be metallic prills of dore metal; and the nonconductive particles would be the slag, free of metal. Middling grains, generally, are in the form of a metallic prill encased in or incompletely liberated from slag. LABORATORY TESTING A number of precious metal slag samples have been tested in the laboratory. It has been found that the composition of slags vary widely from one refinery operation to another. Typical laboratory procedure is to crush and size the slag followed by two-stage lab-scale electro¬static separation. The conductor fractions from the first and second pass are then combined as a prill concentrate; middlings fraction and clean slag tailings from the second pass are held separate. Selected results from laboratory testing are shown in Table 1. It is important to note in Table 1 that the assays represent overall silver and gold, not metallic values. From experience, the laboratory results are typically lower in grade and recovery than the industrial installations. This is largely due to the hydroscopic nature of precious metal slags coupled with the high local humidity in Carpco's Jacksonville, Florida, location. Relative humidity in Jacksonville can range form 60-95%, while most mining locations in the

Jan 1, 1987

By L. H. Munson, D. E. Hadlock, L. F. Munson, R. L. Gilchrist, P. D. Robinson

All uranium mills are required to perform sampling and analysis for radioactive particulates in their gaseous effluent streams and in the environment. Pacific Northwest Laboratory was requested by the U.S. Nuclear Regulatory Commission (NRC) to provide technical assistance to them for their Uranium Mill Health Physics Appraisal Program. In conducting appraisals, air sampling methods used at NRC-licensed mills were reviewed and several deficiencies noted. This paper includes only environmental and effluent particulate sampling although much of the information is applicable to both in-plant and environmental samples. First, the components of a proper sampling program are discussed: program objectives, program design, sampler design, analyses, quality assurance, and data handling. Then the specific deficiencies, or the "pitfalls" from the first 8 mill appraisals are discussed. The first consideration in establishing an air sampling program is defining the objectives of the program. What is air sampling suppose to accomplish? Many of the deficiencies we have observed have resulted because the desired objectives were not clearly established in the minds of the radiation safety staff. PROGRAM OBJECTIVES An environmental air sampling program ought to fulfill the following seven objectives. The first is to: 1) [demonstrate regulatory compliance]. Although a goal of most programs, regulatory compliance, is not well understood. One has not only to comply with the conditions of the source materials licensee, but one must also demonstrate compliance with 10CFR20 and 40CFR190. For example, 10CFR20.106 states: "A licensee shall not possess, use, or transfer licensed material so as to release to an unrestricted area radioactive material in concentrations which exceed the limits specified in Appendix B, Table II of this part .... For purposes of this section, concentrations may be averaged over a period not greater than one year." Even if a mill's license does not require sampling at the site boundary of maximum concentration, a sample may be necessary to demonstrate compliance with 10CFR20. Most mill personnel are painfully familiar with 40CFRl90.10, which states: "Operations.... shall be conducted in such a manner as to provide reasonable assurance that: (a) The annual dose equivalent does not exceed 25 millirems to the whole body.... of any member of the public as the result of exposures to planned discharges of radioactive materials, radon and its daughters excepted... from uranium fuel cycle operations..." This means a licensee's sampling program must give "reasonable assurance" that the member of the general public receiving in the most exposure gets no more than 25 millirems per year. The sampling program necessary to provide that assurance may or may not be a license requirement. However, merely meeting the license requirements and the explicit regulatory requirements does not necessariarly ensure an adequate effluent and environmental air sampling program. The second objective of the environmental air sampling program, is to 2) [identify the source(s) of contaminants]. This will include not only the routine program, but special sampling for verification of sources and nonsources. Only after sampling can a mill operator be assured that roof vents, laboratory hoods, and other localized ventilation systems are not making a significant contribution to environmental releases. An environmental sampling program should also allow the mill operator to fulfill the third objective, to 3) [estimate exposures]. Even before 40CFR190, a sampling program should have provided the mill operator with the information necessary to determine the dose to the "fence post" person, or at least to determine if doses were well below the 10CFR20 limits previously allowed. The program should 4) [detect and measure unplanned releases]. If there is a fire, a scrubber failure, or if a drum of yellowcake breaks open, measured releases will almost always be lower than conservative estimates. Whether or not a system to provide sampling during accidents is needed is almost always a cost-benefit decision. In general, uranium operations do not sample just in case an accident may occur. Yet they may decide on continuous air sampling in lieu of intermittant sampling partially because of the potential for accidents. Another objective of air sampling is 5) [to provide information on the effectiveness of control systems]. This is always a concern with new or modified equipment and may dictate sampling frequency in other situations as well. For instance, if a small leak in a bag filter cannot be detected by other means, then more frequent stack sampling may be indicated. A routine effluent and environmental monitoring program should also fulfill the sixth objective,

Jan 1, 1981

By Violetta Pavlova

Knowledge of geometrical properties of blocks in a hard jointed rock among other things is of considerable importance for prediction of rock mass behavior and for its exploitation. This paper presents a new approach to obtain the information about percentage of blocks with desirable geometrical properties in a jointed rock mass extending through a large region of interest. A model of a rock mass separated by finite number of systems of parallel plane discontinuities which form discrete blocks is discussed. A computational procedure has been derived to analyze the volume and shape distribution of blocks in the rock mass.

Jan 1, 1992

By Paul D. Chamberlin

The evolution of heap and dump leaching has followed the development of agglomeration, materials of construction for leach pads and ponds, solution distribution systems, testing techniques, and state regulations. They are now mature processes. Possible future directions and developments are discussed. In situ leaching of precious metals is waiting to be commercialized. Regulators are reluctant to allow the use of cyanide because of the potential for excursions and operators are reluctant because of the potential for lawsuits. Developments in alternative lixiviants are needed before in situ leaching is accepted.

Jan 1, 1989

By K. Biswas

A finite-element algorithm was developed for an axisymmetric heat-transfer problem involving phase change. The finite-element treatment of the phase-change problem was dealt with by using the enthalpy method. The finite-element algorithm was subsequently applied to model the heat exchange between mine ventilation air and frozen ground in the presence of roof bolts in an underground mine with permafrost. This paper analyzes a single bolt in the problem domain with the convection boundaries at the roof level of the mine airway. A short-term study, comprising the evaluation of roof bolting (friction-anchored type), was conducted, and recommendations were made regarding the applicability of roof bolts as a support system for a given thermal condition.

Jan 1, 1996

By G. H. Jardine

Mine planning and production scheduling in surface mines are basically iterative processes which are ideally suited to the use of computer-based techniques. Both processes are truly three-dimensional and lend themselves to the application of 3-D interactive graphics. Until recently, this has applied the need for the costly, dedicated graphics screens and mid range minicomputers. However, ongoing advances in processor chip design led to the emergence of inexpensive and powerful 5 to 10 Mips desktop work- stations. These workstations have the processing power to support rapid, high resolution, 3-dimensional graphics. By combining these workstations with powerful 3-D CAD software and, with a suite of comprehensive mine planning and scheduling applications, Mincom has developed a most cost effective solution to modern mine planning challenges.

Jan 1, 1989

This paper discusses the type of scaling operations presently in use in underground mines. It defines a scaling factor that is expressed as the area necessary to scale to extract 1 t (1.1 st) of ore. The problems associated with conventional scaling methods are discussed as well as recent developments in mechanized hand-held scaling de- vices and methods of loose detection. The elements of the scaling process are further analyzed. The conception and design of a mechanized scaling device, developed at Universite' Laval is also described. The results of field tests conducted in Quebec hard rock mines are presented. The experimental findings show that the mechanized hand-held scaling device shows potential in improving the productivity and safety of underground mining operations.

Jan 1, 1996

By R. S. Das, A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in terms of complexity and value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer-based predictions and practical results. Research conducted to compare computer results with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only if reliable input data are provided.

Jan 1, 1987

By R. Larry Grayson

A menu-driven, linear-programming- based, user friendly computer program was developed to assist mine managers in determining optimal longwall panel dimensions for a given set of operating conditions. A sensitivity analysis must be performed by varying key mining and configurational parameters over an expected, practical range during the optimization process. Results from analysis of a base case mine indicated that no single combination of longwall panel length and face width is optimal for all operating situations. Each mine manager must therefore look closely at his operating situation and determine the proper dimensions to minimize total mining cost.

Jan 1, 1989

By S. Finsterle, R. C. Trautz

Numerical modeling studies were performed to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is an important factor affecting the performance of a nuclear waste repository, such as the one proposed at Yucca Mountain, NV. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network, as well as on the capillarity of individual fractures intersecting the opening. A high-resolution numerical model of an unsaturated fracture network was developed, and the appropriateness of seepage predictions using a fracture-continuum model was examined. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2002

By Leo Langland

One of the primary functions of the Geotechnical Services-Materials section of the Arizona Department of Transportation (ADOT) is locating, sampling, and evaluating potential aggregate deposits throughout the State. This information is essential in designing, estimating, and bidding highway construction projects. The nature of materials used for aggregate varies greatly within Arizona. The northeastern or plateau section is famous for its scenic sedimentary formations that are, how- ever, too soft to make suitable aggregate. Volcanic materials are widely used in place of more conventional geologic units. In contrast, the southwestern, or Basin-and-Range section, contains a relative abundance of good aggregate, especially a diversity of gravels. The paper will review the off ice, field, and laboratory methods used by the ADOT Materials Section in satisfying its needs for aggregate information in Arizona.

Jan 1, 1987

By Don W. Murphy, Don M. Larsen

Advanced process control has been implemented at the Jerritt Canyon Mill. Plant production prior to 1997 was limited by grind circuit capacity. The installation of additional mill horsepower and an optimizing supervisory control system achieved a throughput increase in excess of 12 percent. The controller application utilized a seamlessly integrated fuzzy logic expert system for real-time mill control coupled with a neural network predictor for closed-loop feedback of particle size constraints. In late 1998, a second supervisory controller was installed to operate the fluidized bed roasters. The second controller optimized roasting conditions, increased plant throughput and improved metallurgical recovery.

Jan 1, 2000

By Steven G. Grannes

The Bureau of Mines, U.S. Department of the Interior, has developed a computer image processing algorithm to determine the size distribution of moving taconite (iron ore) pellets. This algorithm interprets line-scan images to measure pellet diameters. Pellet edge detection with a peak light intensity constraint is the basis of this technique. Preliminary error analysis indicates a normally distributed experimental error with a standard deviation of 0.09 and 0.15 for pellet diameters of 0.4 and 0.9 cm, respectively. System accuracy was independent of moving pellet speed below 50 cm/sec. Computer image-based size distributions were found to be in close agreement with standard sieve analysis.

Jan 1, 1986

By S. D. Thompson, L. Adler

Several researchers in the last 20 years have developed computer simulation models for designing coal mine belt systems. A careful review of these reveals that each omitted or oversimplified important factors, especially in belt loading. To remedy this, the coal mine belt capacity simulator (CMBCS) was developed to include various types of probability distributions, delays, and longwall and continuous haulage. CMBCS is computer coded in FORTRAN and employs the Monte Carlo simulation technique. Basically, the model simulates the loading and corresponding flow of coal through a belt system. By recording spillage and belt stoppage statistics for the simulated flow, belt and surge bin capacities can be evaluated. A complete user's guide is available. The modeling and verification of CMBCS are briefly described, and its major advantages and disadvantages are explored.

Jan 1, 1987

By J. Paraszczak

With regards to the cost and profitability of a mining operation, the performance of the equipment employed is one of the key issues. Cost and profitability depend on, among other factors, the reliability and availability of the equipment. In an attempt to reduce equipment downtime, it is indispensable to collect and analyze reliable data and information on failures and maintenance actions. This paper reviews common problems encountered in this respect, with particular emphasis on the lack of uniform terminology and methodology. Recommendations concerning the standardiztion of reliability and maintainability concepts and measures are given. Regarding the benefits that the latter may bring, the paper concludes with a proposal for an industry-wide initiative in this respect.

Jan 1, 2002

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.

Jan 1, 1987