Search Documents

By M. J. Shields

There are numerous suggestions in the literature on methods of obtaining representative samples of waste rock or mill tailings. Some suggested methods would result in thousands of samples and very high costs for a large facility. There is no general rule that can (or should) be followed, such as collection of a given number of samples per mass of material, per acre of impoundment, or per foot of drillcore. Each site is different, and the adequacy of sampling must be tailored to the site. A logical approach is to let the variability at the site dictate the number of samples that should be collected and analyzed, and then to quantify and evaluate the results by means of standard statistical methods.

Jan 1, 1998

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By John V. Beall

The Mining Engineering Handbook is written primarily for persons interested in the economic extraction of minerals. Not everyone referring to this book will be knowledgeable about mining and, therefore, this section is intended to explain to interested persons the scope of mining as well as fulfilling the title of "Mining's Place and Contribution" among the industries of society. 1.1-MINERALS, ROCKS AND ORE In the year 1971, the number of known elements amounted to 104. Fifteen of these have been made only in the laboratory, others may have persisted from the primitive atmosphere, but, by and large, elements originated from magmas or igneous rocks of the outer rocky shell of the earth. Only eight elements constitute 98% by weight of the earth's crust. These are oxygen, 47%; silicon. 28%; aluminum, 8%; iron, 5%; and sodium, magnesium, potassium and calcium, less than 4% each. These common elements and the other less common ones are the building blocks of minerals, of which there are over 2,000 varieties. According to Webster: "A mineral is an inorganic substance occul.ring natura!ly in the earth and having a consistent and distinctive set of physical properties and a composition that can be expressed by a chemical formula. The term is sometimes applied to organic substances, such as coal." Thus, minerals are precise combinations of elements. Rocks, as distinct from minerals, are composed of assemblages of minerals. When minerals are found in sufficient concentration to warrant extraction by mining, the mineralized area is considered an ore deposit. The definition of ore is mineral that can be extracted from the ground at a profit. The economic connotation is implicit in the word ore. Since most of the useful elements compose such a small percentage of the earth's crust, the occurrence of ore deposits as we know them would not have transpired had not geologic processes concentrated the elements (see Sec. 4). 1.2-DEFINITIONS OF MINING TERMS Extensive coverage of the many descriptive terms used in mining may be found in a good mining glossary, such as is available from the Superintendent of Documents (see Sec. 35), but for convenience a number of the more common definitions are given here. Mining may be defined, as by A. B. Cummins, as the act, process or work of extracting minerals or coal from their natural environment and transporting them to the point of processing or use. Mining techniques are applied to extracting metallic minerals, such as ores of gold, copper, lead or zinc; to fuels, such as coal, anthracite, lignite and tar sands; and to nonmetallic minerals, such as lime-

Jan 1, 1973

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By Błażej Doroszuk, Robert Król

Mill drums are essential equipment in various industries for the comminution of materials. To optimize their design and operation for efficient and cost-effective processing, it is necessary to understand the behavior of the mill drum under various operating conditions. This study investigates the behavior of a mill drum using a combination of experimental and numerical methods. The factors that can influence the behavior of the mill drum, such as the size and shape of the mill, grinding media, rotational speed, filling level, and material properties, are discussed. Experimental methods can be limited in obtaining measurements of internal processes, so numerical methods such as the Discrete Element Method (DEM) are also used to simulate the behavior of the mill drum. In this study, the experimental measurements of the motion of the grinding media are obtained using computer vision methods, and the numerical simulations are calibrated using the experimental results. A designed experiment approach is used to evaluate the performance of the mill drum under various operating conditions. The results of this study can be useful for the design and optimization of mill drums to achieve better performance and energy efficiency.

Jun 25, 2023

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023

By W. A. McKinney

The U.S. Bureau of Mines, Kennecott Copper Corp., and New Mexico Institute of Mining and Technology are cooperating on a research project to improve extraction of copper from previously leached waste dumps that are in part compacted and impervious to leach solutions. The field work is being done at the "J" leach dump, Chino Mines Division, Kennecott Copper Corp., Santa Rita, N. Mex. The laboratory percolation leaching tests were made at the U.S. Bureau of Mines Salt Lake City Metallurgy Research Center on drill core samples from the "J" dump to determine how much copper might be leached if permeability could be restored by explosive heaving or other means. The core samples from nine drill holes on "J" dump contained from 0.06 to 0.14 percent copper. Copper extractions ranging from 15 to 3 percent were obtained in 75 days by percolation leaching of minus-1-inch material with dilute sulfuric acid. The tests results indicate that about 2'7 percent of the copper remaining in the "J" dump could be extracted under ideal leaching conditions.

Jan 1, 1970

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By K. E. Doud

An unusually pure grade of rutile and several grades of aplite rock are produced in a unique mining and mineral dressing operation in Hanover County, Virginia. The ore body is an aplite rock of gnessic structure, having a sari ace exposure extending over several hundred acres, heavily leathered and containing rutile, ilmenite, and other titanium and iron minerals. The physical nature and mineral composition of the ore body has permitted the use of a relatively economical and unusual processing circuit. The flowsheet was designed to take full advantage of the remarkable liberation of the minerals at relatively coarse rinds. It permits flexibility in changing the product mix, and maintains high levels of purity in both rutile and aplite rack. The mineral processing is discussed in some detail below.

Jan 1, 1962

By T. Lupek, M. Buxton, A. de Jong

"With regard to the EU funded project ‘Real-Time Mining’ a sensor-based acquisition, collection and transmission of data for the resource extraction process will be developed. The key concept promotes the change in paradigm from a discontinuous to a continuous process monitoring. Especially concerning material characterization, machine performance and underground positioning ‘Real-Time Mining’ will provide sensor solutions as well as the interfaces for integration, management and visualization of the collected data for a permanent updating process of the resource model with the aim of near real-time optimization of decisions. On the basis of ‘Real-Time Mining’-Output a permanent monitoring of costs can be performed as well in both, the installation and the production process of a mine. Due to the collected data in terms of machine performance connected with the underground positioning information added with personnel tracking and mine surveys a comprehensive overview of process performance is available. By evaluating those information in a specific manner costs per unit will arise for monitoring and possibly controlling actions. INTRODUCTION By having a look into the future of mineral extraction projects, a new challenge for the Ore Mining Industry will arise in the short and medium term. Due to the depletion of currently mined mineral reserves in addition to the persistently high demand of mineral raw materials, the extraction of complex reserves will be necessary. By characterizing such deposits as not constantly graded and geometrically varying, the extraction process, especially concerning the requirement of a minimized zero-value material handling, will become economically ineffective by utilizing the traditional mineral resource management methods. Regarding the state-of-the-art mineral resource management process along the mining value chain, an intermitted, discontinuous sequence of actions is applied (Figure 1). Recently data will be collected from drill hole cores. These rock samples are analyzed in a laboratory. Based on those analyses a resource model is created whereby unknown data between drill holes is interpolated. This resource model is the basis for all mine planning actions including the selection of the mining method, extraction sequencing and the prediction of the expected performance. With the start of the production, real conditions (concentrations of elements, hardness, stability, etc.) can be observed and measured. As the production process is running accordingly to the above described mine plan, the verification of the initial assumptions happens at the earliest after processing of the extracted material. Even if deviations between the predicted and the actual performance are now recognized, the execution of corrective actions is not possible anymore."

Jan 1, 2016

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By S. Tafazoli, D. Cooper, I. Bell, S. Nouranian, B. Sameti, M. Ramezani

"Image-based rock fragmentation sensing in mines and quarries includes an important rock boundary delineation step, commonly referred to as rock segmentation. This paper presents an artificial intelligence-based solution to this challenge. The proposed technique encodes prior knowledge of previously analyzed images into mathematical/statistical models. Human-labeled images are used as inputs to train neural networks through an optimization process. The networks can then be used in real time for rock delineation. To build the models, special deep artificial neural networks are used as a pixel classifier. The proposed classifier labels each pixel (edge, rock or fine) by analyzing a plurality of pixels within the image. Advances in machine learning allow the network to contain many parameters. The increased number of parameters is a strong factor in the classifier’s ability to correctly classify each pixel. Deep learning-based segmentation, combined with 3D imaging followed by post processing, provides a unified fragmentation sensing solution. Results from automatic segmentation are compared to human labeled segmentation using the percentage passing curves for 64 rock images. INTRODUCTION Mines and quarries can see significant productivity and performance benefits by controlling material sizes (McKee, Chitmobo, & Morrell, 1995; Sellers & Gumede, 2012). During the past decade, image-based fragmentation analysis has been applied to estimate rock size distributions in order to optimize procedures in mines and quarries. Using a roving camera and operator assisted analysis Maerz, Franklin, and Coursen (1987) measured the size distribution of the blasted rock and eliminated the need for manual sieve analysis. Since then, many others have introduced automated and manual methods for fragmentation analysis and improved upon existing approaches (Girdner, Kemeny, Srikant, & McGill, 1996; Smith & Kemeny, 1993; Palangio, Palangio, & Maerz, 2005; Tafazoli & Ziraknejad, 2009; Raina, 2013). In image-based fragmentation, rock boundaries are identified in the image, and an image scaling is applied to transform rock pixel sizes into real world dimensions. Usually geometric references, such as regularly shaped objects (discs and basketballs) (Siddigui, Ali Shah, & Behan, 2009), or the known size of an excavator bucket (Zeng, Chow, Baumann, & Tafazoli, 2012), are used to determine the proper scaling factor. In recent years, 3D imaging and sensing have also been incorporated to improve rock delineation. Specific methods include using camera-laser combinations and stereo imaging to measure rock fragmentation on conveyor belts (Noy, 2013; Thurley, 2013; Dislaire, Illing, Laurent, & Pirard, 2013) as well as portable fragmentation analysis devices with 3D imaging sensors (Sameti, et al., 2014)."

Jan 1, 2018

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By Robert J. Neubauer

I was asked here today to discuss the first long-term freight rate contract ever signed by a U.S. railroad and shipper. That was ICG's contract with the hoosier energy company to haul coal from southern Illinois to an Indiana power plant. I?ll also talk about why you can expect to see more such contracts in the future But first, let me tell you a little bit about the Illinois central gulf railroad and why coal contracts are so important to us. ICG is a principal mid-American freight carrier. We are one of the ten largest railroads in the united states and one of the ten largest coal-hauling railroads. ICG links the industrial great lakes region with the warm weather ports of the gulf coast. Some of the major points on our route map are Chicago; Indianapolis; Omaha; Kansas City; Memphis; St. Louis; and, of course, baton rouge and new Orleans.

Jan 1, 1981

By K. H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modi tying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identity and quantity operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By Jay Parrish

Appalachian kimberlites appear to be spatially distributed along two structure parallel trends running from Tennessee to New York. It is hypothesized that the kimberlites were emplaced at the intersection of structure parallel basement faults and cross- structural lineaments. The latter are expressed in potential field and remotely sensed data. The western trend follows the Rome Trough from eastern Kentucky to south central New York. The eastern trend parallels the edge of the Ridge and Valley in Virginia and Maryland.

Jan 1, 1984

By Gregory E. Korbin

The effectiveness of pre-reinforcement as an immediate stabilization measure as well as its contribution to the permanent stabilization of a tunnel were studied through the use of physical (Figure 1) and numerical models (1). Physical models were designed for the investigation of two pre-reinforcement systems: first, reinforcing far ahead of the main excavation (Figure 2); second, spiling reinforcement ahead of the face (Figure 3). In both cases, the use of reinforcement was responsible for permanently stabilizing an otherwise unstable opening. Data from the physical models were used to calibrate a numerical model from which additional information on long term behavior, methods to account for the capacity of a pre-reinforcement system, and the mechanisms involved were ascertained. These studies indicated that pre-reinforcement can stabilize a rock mass effectively as it reduces deformations and thereby deterioration due to strain softening, provides rock mass confinement leading to increased available strength, and maintains rock arch continuity allowing for increased tangential stress in the immediate vicinity of the opening. Field studies verified the capacity of spiling reinforcement to restrain initial deformations.

Jan 1, 1976

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering. There exist no standardized methodologies for their computer implementation. In meeting this need, this paper introduces the concept of a process software model, or simply a software model and presents a two-step methodology for its development involving software model specification and development. The software model specification is to be performed after extensive discussions with the ultimate users of process software based on which the software model is developed. These software models provide a formal basis for the design and construction of software objects corresponding to the real world process objects.

Jan 1, 1994