Search Documents

By A. Smith

The practice of leaving barrier pillars between adjacent longwall panels at The Durban Navigation Collieries (Pty) Ltd (Dumacol) has resulted in a considerable loss of coal reserves. Dumacol has now modified the layout of its longwall panels to allow the concurrent mining of barri9f pillars and the extraction of the longwalls. The Implementation of the new panel layout has increased the percentage extraction of reserves and will result in an extension in the life of the mine. The method of extracting barrier pillars between adjacent longwall panels is described in this paper.

Jan 1, 1985

By J. A. C. Diering

The simulation of mining in faulted ground was recently described by Crouch. His method is extended here to enable a wide range of non-homogeneous mining problems to be modelled. Essentially, the boundary conditions at geological interfaces are incorporated into the overall iterative solution, which is necessary if faults and joints are to be modelled realistically. Two examples are given to demonstrate the method: the mining of coal a seam below a thick dolerite sill, and the mining of a flat reef in close proximity to a vertical fault where hangingwall and footwall rocks have different properties.

Jan 1, 1980

Introduction to high temperature oxidation of metals, by N. Birks and G. H. Meier, London, Edward Arnold, 1983. 19S pp. R30,25. Reviewers: M. B. Cortie and G. G. Garrett Seam gas drainage with particular reference to the working seam, edited by A. J. Hargraves. Woollongong, The Australasian Institute of Mining and Metallurgy. 370 pp. $A30. Reviewer: C. J. Fauconnier New books Solvent extraction Part I, by G. M. Ritcey and A. Ashbrook. Amsterdam, Elsevier, 1983. Elektronishche Steuerungen und Mikroprozessoren im Bergbau. Sicherheit und Zuverlassigkeit Environmental impact control. Philosophical and procedural guidelines for the planning professions Mineral processing and extractive metallurgy. Reagents in the minerals industry.

Jan 1, 1984

An investigation into the stability of large open stopes at Premier diamond mine, Culinan, South Africa, is described. The open stopes are located in a weak kimberlite orebody, directly underneath a 75 m-thick sill of gabbro. Two and three-dimensional stress analyses were carried out in a back-analysis of the stresses and failure around the first open stope created under the sill. The results were used in the prediction of the future stability of the planned open stopes, intervening pillars, and sill.

Jan 1, 1987

By M. U. Ozbay

This paper presents an overview of the research that has been carried out to improve the understanding of the fracture processes occurring in rock under high levels of stress. The onset and growth of fractures are studied by means of laboratory model testing, and the results obtained are used in the calibration and validation of the numerical model DIGS, which is based on displacement discontinuity. The results obtained so far have shown that, while there are overall similarities between the experimental results and the numerical simulations, improvements to the experimental procedures and the DIGS are required for a detailed mechanistic understanding of shear-band orientations and extension fractures.

Jan 1, 1996

By A. N. Brown

Rock breakage by drilling and blasting is fundamental to every hard-rock mining operation. The subject was an apt choice for a mining school because many technological changes have taken place since the subject was last presented some ten years ago. However, because of the development of surface mining, it was decided that two schools should be held: one for underground mining, and the other for surface mining. The School on Underground Mining was held at the University of the Witwatersrand in February 1986.Copper 87 COPPER 87 is an international conference organized by metallurgical and academic institutions of two of the largest producers of copper in the world, Chile and Canada.

Jan 1, 1986

By K. C. Wilson

Recent experiments and analyses have provided greater understanding of friction losses for the size distribution of the particles forming the slurry. Wilson and Sellgren (2001), Wilson et al. (2006) and Sellgren and Wilson(2006) have proposed a multi-component model consisting of carrier fluid and pseudo-homogeneous, heterogeneous and fully stratified solids. The technique presented here was found to estimate friction losses well when compared to reported experimental results with pipelines with diameters mainly from 0.2 to 0.5 m for various mixtures of fine sand to coarse gravel and products from mineral processing and phosphate mining.

Jan 1, 2007

By M. N. James

The Fracture Research Group has been operating at the University of the Witwatersrand for some ten years and, in that period, has achieved a significant profile, both nationally and internationally, through its research publications, industrially-based technical reports, continuing short courses in engineering education, and co1Jferences. This paper outlines the activities of the Group over the past few years, emphasizing the research thrusts and the results that have been obtained, as well as highlighting areas of current and future research interest The capabilities of the Group in terms of equipment and expertise are also discussed briefly.

Jan 1, 1995

By W. J. Van Den Berg, J. G. Taylor

The paper discusses the introduction of blindhole boring on the South African gold mines of Anglo American Corporation. It covers the boring trials conducted, and outlines the progress made in the development of blindhole borers. The operating costs, and performances, of the latest 1,52 m diameter borer are given. Future trends and requirements In the application and design of blindhole borers are discussed, as well as factors that are of importance in the design of future machines.

Jan 1, 1978

From a consideration of the functional requirements of a stope-support pack, simple design principles were developed. The material and dimensional properties of the different components of the pack were determined from a series of laboratory tests. The most important requirement for an adequate pack is that the cushioning layers of timber between the concrete brick layers should provide sufficient transverse reinforcement. The tendency of the compressed timber to creep is shown to be a serious limitation to pack performance and must therefore be an important consideration in the overall design of supports.

Jan 1, 1978

By J. D. Wells

An account is given of the planning required for the rehabilitation of land that is to be disturbed by opencast mining, and of the preparation of rehabilitation of land that is to the Inspector of Mines. The plans Include the provisions that are to be made to allow for climatic conditions, land use, vegetation and wildlife, surface-water resources, geology and ground water, soils, land capability, rehabilitation method, location of discard dumps and slurry ponds, pollution control, and costs. . . Monitoring of the operation is the only way that the rehabilitation plan can be improved, and both monitoring and planning are essential when provision is being made for the closure of a mine.

Jan 1, 1986

By P. H. Botha

An account is given of the procedures used by the South African Iron and Steel Industrial Corporation (Iscor) for tests on the flotation of coal fines, and some of the beneficiation problems encountered with coal from Durnacol, Grootegeluk, and the Soutpansberg area are discussed. These, and other South African coals differ from overseas coals in that they contain a high percentage of fixed ash, which means that they have to be crushed more finely for liberation and that they then contain more fine material (smaller than 0,84 mm). In addition, the coal from the three areas mentioned occurs in fine layers and seams, and contains many intergrown particles.

Jan 1, 1980

By O. S. Lubbe, G. Annandale, J. W. van Wyk

This paper deals with the development and evolution of room and pillar mining in the South African chromitite and platinum mining industry over the past sixteen years. The paper describes the need for cheaper, more effective and safer mining methods in hard rock mining. It also describes how a mining method traditionally only applied in coal mining in South Africa evolved into a method ideally suited to conditions in chromitite and platinum mines. The paper also touches on joint efforts from mining houses, mine management and equipment manufacturers to design and build mechanized equipment custom designed and unique to South Africa in order to overcome challenges presented by the harsh operating conditions encountered in the mines in the Bushveld Complex.

Sep 1, 2001

By T. A. Claasen

Exceptionally low yields in the coking-coal fields of the Soutpansberg area in the northern Transvaal, are taxing the skill and ingenuity of preparation engineers. The coals are highly intergrown, and a series of crushing and washing steps may be required to extract the maximum usable tonnage. In addition, novel preparation techniques may have to be employed. This paper, which is a case study of work recently undertaken, gives a general account of raw coal properties, emphasizing those related to maximum recoveries, and outlines the steps involved in the design of appropriate flow sheets based on laboratory studies.

Jan 1, 1980

By L. Dison, J. A. Hahn, G. E. Blight

A system of artificial support for shallow mines is described, analysed, and evaluated. The system can be designed rationally to support a predetermined overburden load, and tests have shown that the design theory gives accurate predictions of strength. The support system, consisting as it does of two basic materials, reinforced granular material and reinforced cemented material, is flexible and can be varied to suit changing requirements of height and load. The system of preloading to the design load by jacking off the roof ensures that the walls are both stiff and prooftested.

Jan 1, 1982

By M. G. B. Wheeler

SYNOPSIS This report outlines the development of a model to simulate the radiometric sorting of gold- and uranium-bearing ores. The developed program indicates the optimum mass, reject percentage, and expected reject gold and uranium grades for a radiometric sorter. It achieves this by statistical analysis of the data gathered from a large sample of rocks in the required size range for a particular mine. The program can be used in the optimization of existing sorters, as a design tool for new radiometric sorters, and in feasibility studies on radiometric sorting.

Jan 1, 1989

By G. J. Kringe

The results of a series of measurements of accelerations and guide-roller loads made on mineshaft conveyances are given, together with the predictions of these accelerations and loads based on a computer programme. The analysis of the measurements is described, and the results of the measurements and computer predictions when compared show reasonable agreement. Some parameters that increase the guide-roller loads are identified, and their effects are studied, together with some comments on the total loads. Finally, a possible format for a design specification is discussed, and some tentative design values are given.

Jan 1, 1986

By J. A. C. Diering

The determination of stresses and displacements close to tabular excavations is of considerable importance in the planning of tunnels and of remnant and pillar layouts. This paper gives a description of a simple yet effective method for the achievement of improved values from an analogue or MINSIM type of analysis. Essentially, closures and rides (the movement of hanging-wall relative to footwall) in mined-out areas are assumed to vary in a piecewise linear fashion as opposed to a piecewise constant fashion. As the former fashion more closely resembles the true variation, it is possible for the stresses and displacements at points close to the excavations to be calculated with much better accuracy.

Jan 1, 1980

By M. J. H. Tonkins, C. C. Crosson, G. Paterson

The development of drilling and blasting practice at Palabora Mining Company Limited by c. C. CROSSON, Pr. Eng., A.C.S.M. (Hons), BASe. (Min. Eng.) Toronto, M.!.M.M. (Member), M. J. H. TONKING, Pr. Eng., A.C.S.M., BASe. (Min. Eng.) Toronto, M.I.M.M. (Member), and G. PATERSON, B.Se. (Min. Eng.) Glasgow, M.!.M.M. (Visitor) Open-pit drilling and blasting practice at the Palabora Mining Company Limited is described, with particular reference to the development of aluminized slurry explosives. Rotary drilling of primary drill holes, drilling patterns, and blasting techniques for use with slurry explosives are described.

Jan 2, 1976

By A. J. S. Spearingt

The hydraulic transportation of relatively dense slurries for backfill purposes is typically carried through vertical and horizontal pipelines under gravity. Wear in backfill pipelines has become such a major problem that it is now one of the main reasons for the relatively slow build-up of placed backfill in spite of encouraging performance results in the gold-mining industry. This paper describes tests on pipeline wear that were carried out on classified tailings from the backfill plant at Vaal Reefs East. The testwork was carried out under various conditions of slurry relative density, slurry velocity, and pipeline diameter. Empirical relationships are presented for each transportation and pipeline parameter evaluated and, finally, overall relationships between pipeline conditions and transportation parameters are proposed.

Jan 1, 1992