Search Documents

By J. D. Salter

Most diamonds are liberated from their ores by crushing. Diamond and other coarse grained mineral ores require carefully optimised crushing circuits. Recent advances in computer technology have made possible the on-line capture of crushing plant performance data and, hence, the accurate empirical modelling of the crushing process. Such models are used in simulation studies to determine the optimum operating conditions for a given plant. A system is described which allows operating data from mineral treatment processes to be logged. Up to 16 channels of data may be recorded simultaneously at sampling rates in the kiloHertz range per channel. A data storage and analysis procedure is described which allows the system to make full use of its sampling capabilities.

Jan 1, 1987

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

By I. Wigden

This paper discusses system integration and installation of High-Tec systems in underground mines. ABB has the capability to be a System Integrator and co-operates with partners in different areas of technology. Today it is difficult to find one Company that is responsible for the complete Automation System. The design of the system is also dependent on the caving procedure that is currently being used in mines. Most of the engineering must be done during the feasibility study and the design phase. Any mistakes made during these phases will be costly to rectify in the commissioning phase. The paper will also include a presentation of the benefit of using Automation in an Underground Mine, and the importance of integration with the people component. Most of the experience and discussions in this paper are from different technologies that have been developed in Scandinavia and adopted from LKAB in Kiruna. The author of this paper was responsible for the Automation projects in Kiruna Mine during1994 - 1999. These projects include: • Broadband communication of data, audio and compressed video in one data stream. • Control System for Haulage -1045m • Automation of Load Haulage and Dumping machines (LHD) • Control of Production Drilling Rigs from a Central Control Room.

Sep 1, 2001

By Timo Niitti, Sami Grönstrand

n today's marketplace with high metals prices, many operations are faced with the challenge of improving recovery and at the same time maximizing availability. New operations under feasibility studies have the same requirements, with the additional need for ever higher capacities. Economies of scale have proved a vital competitive advantage in the game of ore dressing. Flotation is the most widely used method for extracting valuable minerals from ore - despite its mature age of 100 years. Customer demand has driven the development to increasing cell sizes, and in most cases, this has brought the advantages of both lower capital expenditure and lower operational and maintenance cost. The challenge of scale up, however, is to meet the metallurgical performance requirements in the larger volumes. The paper outlines recent trends and developments in flotation technology, and presents new solutions designed to address the needs for increased capacities as well as improved performance. Whether the goal is to improve existing operations or to scale up new equipment, computer aided tools are playing a key role in shortening the development cycle and reducing costly trial-and-error tests in full scale. Using the new tools and validation thereof will be outlined, as well as the development principles behind the new solutions. Plant results and experiences with the new developments are presented and discussed in several cases around the world.

Jan 1, 2007

By K. R. Johnson

Changes in the pattern of computer systems for mine planning and geologic evaluation are occurring as a consequence of the introduction of 3-D high performance graphics terminals. The VULCAN system is described and an outline of its functionality is discussed. Increasingly, the integration of both database systems and graphics and databases will occur, allowing a greater degree of information access to mine operators. The system covers areas of database, drillhole graphics, mine design and layout, surface and solid modelling as well as reserve inventory generation. The design of the software is such that it is fairly commodity-independent and entirely menu-driven, to enable non computer-trained personnel easily to access the system.

Jan 1, 1987

By R. I. Klintworth

The multi-reef area of Cooke 3 Shaft provides a unique mining challenge on account of the very thin middlings between the pay bands and the marginal values of the reef. It is uneconomic or impractical, because of the excessive heights, to mine the middlings using conventional stoping methods. The development of suitable mining methods is discussed with particular emphasis on the control of water inflow and the policy of not jeopardizing or sterilizing other reef horizons by the mining method implemented. No definite solution is currently available, but with the aid of instrumentation, computer analyses and mechanized mining equipment, the mine continues to attempt to maximize extraction and profits.

Jan 1, 1988

"Chairman: Dr DeV. HarrisRapporteur: Mr A.H. MunroPapers:Corporate exploration strategies by MacKenzie, B.W.The Engel Simulator and the search for uranium by Griffiths, J.C. and Singer, D.A.The Chairman opened the session by tracing the changes which have taken place in the exploration field since the days of the lone prospector who relied upon his individual skills and to a large extent on luck. The deposits which now remain to be discovered are better covered and are of lower grade. A much greater team effort, involving geoscientists and engineers, is required. The gamble is thus much greater -not only are the probabilities of failure still significant but the consequences are more severe. A recent Canadian survey indicated that expenditures of between two and nine million dollars on regional exploration programs are required to locate one significant deposit.The Chairman went on to say that these facts have led companies to regard exploration as another form of investment and to treat it accordingly. This had placed exploration in the context of corporate strategics and structures, which was the subject of the first paper of the session.In introducing his paper, Dr B. W. MacKenzie said that the paper suggested a decision framework for exploration planning. Initially the environment is analyzed to define observable and relevant economic characteristics. The terms of reference for exploration planning and the appropriate allocation of capital and skills are then established in the light of corporate objectives and growth alternatives. With the aid of this information and in the light of profit and corporate risk criteria, exploration strategies can be selected.Dr MacKenzie went on to say that the usefulness of the concept and criteria outlined in his paper depended critically upon three characteristics of any particular economic environment, namely, the return resulting from an economic discovery, the unit discovery Cost and the probability of making an economic discovery. He then showed by means of a case history relative to the Canadian Shield and Cordilleran areas that these three characteristics could, in fact, be evaluated for regions with reasonable histories of mineral activity.The first contributor to the discussion of the paper, Mr Alfred Weiss, mentioned that his group had been involved in exploration modelling for some ten years and were thus particularly interested in the paper. He went on to say that they had experienced greatest difficulty with reconnaissance programs and that he sensed that these difficulties were also present with the methodology which had been outlined. Mr Weiss asked Dr MacKenzie how he would deal with such situations when no information was available but where there was the potential for both exploration and discovery. Dr Mackenzie agreed that the lack of information was a very severe limitation and said that at the present time his methodology probably did not provide a basis for breaking down the broad geological regions he considered into areas for further assessment."

Jan 1, 2014

[Council for 1993/94 President Dr H. Scott-Russell President Elect J.A. Cruise Vice Presidents Senior D.A.J. Ross-Watt Junior P.D.K. Robinson Immediate Past President J.P. Hoffman Honorary Treasurer J.A. Cruise]

Jan 1, 1994

By J. D. Koch

The past ten years or so have seen many changes in the methods and approach adopted for projects in the metallurgical and mining industry in South Africa. These changes have led to an increased use by operating companies of the project and construction management services offered by engineering contracting companies. For a variety of reasons, this development has been slower in the metallurgical industry than in other areas of production, but that industry is also now showing an increasing trend in this direction.

Jan 1, 1981

By P Clive Hart

DRA - BACKGROUND [MULTI MINERAL DESIGN & BUILD COMPANY FOUNDED 1984 ENGINEERING FOCUSED CORE ENGINEERING DISCIPLINES INCLUDE: ?PROCESS ?MECHANICAL ?E&I CONTROL PRIVATE COMPANY, INDEPENDENT & INTERNATIONAL]

Jan 1, 2006

By S. Neilson, M. G. Demmer, K. McCarogher

The Phoenix Programme takes the Mining and Mineral Processing Industry into the Science Classroom In the early years of mining, methods were crude, simple, labour-intensive, and very slow. Human resourcefulness, however, created innovations (mechanization, and computerization), that resulted in faster development, greater tonnages of ore, more efficient separation, and a superior final product. This expansion occured an ever-increasing rate, and resulted in a booming mining industry and a growing economy.

Jan 1, 1989

By C. Ringas, F. P. A. Robinson

Various theories proposed to account for microbial corrosion are reviewed as a background to a better understanding of this type of corrosion in iron-based alloys. Experimental evidence is presented to show that even stainless-steel alloys are prone to microbial attack by sulphate-reducing bacteria. The corrosive attack by the bacteria is due primarily to the hydrogen sulphide that is produced as part of their metabolic processes.

Jan 1, 1987

By A. W. de Villiers

This paper explores the behaviour of methane in the goaf during longwall mining, together with some methods for the control of methane emissions into the goaf, the working face, and the ventilation system. Experimental work done at Twistdraai Colliery, Sasol Coal, is referred to, as well as the gas-drainage system being practised at West Cliff Colliery in New South Wales, Australia. Gas drainage is discussed briefly, and certain suggestions are made in regard to coal mining in South Africa.

Jan 1, 1989

By D. G. Hulbert, D. Tudors, M. L. Coetzee, I. K. Craig

The paper describes how a multivariable control scheme was developed and implemented for the run-of-mine milling circuit at a gold mine belonging to Vaal Reefs Exploration & Mining Company Limited. The key variables that are controlled are slurry level in the sump, mass of material in the mil, and product size. The control scheme has resulted in reliable control of the dynamics of the plant, and has provided a good basis for the optimization of plant operation by the selection of suitable set Points.

Jan 1, 1990

By R. Rubin, P. A. Laxen, G. S. M. Becker

An account is given of developments in the use of activated carbon for the recovery of gold from cyanide solutions. The carbon-In-pulp process employed at the Homestake Mine is described, and its various applications in South Africa and their effectiveness are discussed. Probable future work on the carbon-in-pulp process and other possible applications of carbon for the recovery of gold are outlined.

Jan 1, 1979

By J. P. M. Hojem, C. Dimitriou, N. C. Joughin

This paper describes the design and construction of the first experimental underground rockcutting machine from measurements of cutting forces determined in tests on small rock specimens in the workshop. The deficiencies of this design, revealed by stoping with almost identical rockcutting machines, are described. An account is given of the design and construction of further experimental machines incorporating substantial improvements which made them technically feasible for use in production.

By A. Whillier

Recovery of energy from the water going down mine shafts by A. WHILLIER, Pr. Eng., Se. D. (M.I.T.) (Fellow) The influence of energy-recovery systems on the rise in temperature of water going down mines is examined. It is concluded that the, cost benefit of such systems, deriving partially from the reduced temperature rise in situations where cold water IS sent underground from surface, would more than justify the installation cost.

Jan 4, 1977

By D. Gerhart, J. Hung, J. Hackwood, A. Pix

A computer-based, real-time mine management system has been installed in a number of underground operations. The system’s innovative software application is coupled with wireless data acquisition and database management to provide complete mine monitoring and control execution in closed-loop control fashion. The system is well suited to automatically assign equipment, acquire status, and reassign resources based on status; and to automate information handling. The system has provided mines with improved utilization of the equipment fleet and mining crews, and reduced workplace cycle time. This paper describes the deployment of systems at a number of underground mining operations and discusses future development of the system. Keywords: Computer-based: Real time: Utilization: Mining cycle control: Monitoring: Productivity

Sep 1, 2001

By C. O. Beale

This paper is the first part of a two-part review on the subject. , , .. Here reference is made to the place of copper among the elements, Its properties, Its historical significance, and its 'end uses both in general and in South Africa. Its current market situation and its prospects are dealt with briefly. Some account is then given of the mining and metallurgical techniques employed. in South Africa in the production of copper, together with the names of the companies at present Involved and brief descriptions of their operations, ,... . .. The operations of these companies are described In greater detail In Part 11(Apn11985 Issue of the Journal).

Jan 1, 1985

By R. C. Hochreiter

The paper gives a technical review of the history, occurrence, mining, metallurgy, and end-uses of the platinum-group metals in South Africa, with most emphasis on platinum and palladium. The platinum industry has grown, from the first discovery of the metal in South Africa (in the central Transvaal) in 1923, to the present time, when the country is the largest producer of platinum 10the world, supplying almost 70 per cent of the platinum on the world market.

Jan 1, 1985