Search Documents

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012

By C. A. Snyders

The research presented in this paper investigated the practical aspects of the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were conducted on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of Pt, Pd, and Au were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours, and 100 per cent for Pt, 97.4 per cent for Pd, and 99.9 per cent for Au after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while Ni concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, Ni adsorbs at approximately the same rate as the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. The equilibrium loading of gold is exothermic in nature (Fleming and Nicol, 1984) which will result in an increase in gold elution kinetics with an increase in temperature at similar pre-treatment conditions. A similar result was found for the elution of Pt and Pd. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and results suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing due to increased ionic strength.

Jan 1, 2013

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By I. Nolet

Matte tapping is one of the most critical operations of a matte smelter. Every smelter has developed particular matte tapping practices and tap-hole repair strategies that are often based on the experience of the smelter personnel. As a result, very little information has been published on these critical topics. This paper aims at providing the information gathered from a survey conducted in the PGM and Ni industries on matte tapping practices and tap-hole maintenance strategies for different PGM-Ni matte smelting operations.

Jan 1, 2014

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By K. Bryan, O&apos

A 10-year program to integrate crushing and screening models into daily flowsheet design practice has proven successful. A Circuit Analysis Program (CAP) is used worldwide to design and evaluate new and existing crushing flowsheets. To gain user acceptance of CAP and maximize effectiveness, model development, simulation flexibility, ease of use, and developing international access are key issues. These issues have been resolved effectively resulting in flowsheet simulations to assist in justifying increased capital investment. CAP is presently utilized in Canada, United States, and South Africa with intentions to expand to Europe and Asia.

Jan 1, 1987

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By K. R. Noble

The planned extraction of the No. 1 shaft pillar at Blyvooruitzicht Gold Mine highlighted a number of potential problems. In spite of the relative shallowness, careful thought had to be given to stope phasing owing to the detrimental effect of the anticipated geology and the fact that uninterrupted hoisting was necessary. Extensive use was made of computer modellig to design the stope phasing, determine the influence of regional support and to predict the direction and magnitude of displacements in the shaft. The paper describes the success of this design approach, and measured displacements in the stoping horizon and shaft barrel are compared to those obtained from the original computer model

Jan 1, 1987

It is desirable to have a model, or method, for major project development, which will enable flexible modelling of separation circuits. This ability improves the understanding of circuits and how they should be operated, especially in a design phase, where various options are evaluated and decisions are made on the required number of stages and configuration. This paper describes existing gravity separation circuit modelling theory and concepts, as defined by Holland-Batt1 (separation window, separation efficiency and proportionality of efficiency). The crux of the paperis the application of numerical analysis to fit raw separation data by means of a modified Bézier-Spline. The paper proposes an alternative to the theory developed by Holland-Batt that provides more flexibility in the modelling of separation stages and curves, which include S-shaped curves. The paper proposes a solution to the challenge of continuously extrapolating data, and the first difficulty normally encountered, which is the fitting of an appropriate empirical formula to raw data.

Jan 1, 2007

By E. Minnaar, P. J. Cilliers, M. Bellino, L. M. Roux, R. Dye

The classic technique to remove impurities in a cobalt stream is selective precipitation. This is usually followed by re-leaching to produce an advanced electrolyte for cobalt electrowinning. Although this technique ensures an adequate cobalt concentration in the electrowinning circuit, some of the consequences include unwanted losses through the numerous selective precipitation steps resulting in lower recoveries. One plant that currently utilizes selective precipitation is the Luilu Metallurgical Plant (Luilu) in the Democratic Republic of the Congo. This paper evaluates the benefits of using solvent extraction technology as a purification step in the Luilu Process with the aim of further increasing the overall cobalt recovery and to ensure that a suitable cobalt concentration in the advanced electrolyte is achieved. The implementation of a solvent extraction-electrowinning process is found to be beneficial in terms of achieving improved recoveries and cobalt cathode quality, however there are many other factors that impact the success of converting from the classic precipitation process used at Luilu.

Jan 1, 2007

By D. Royston

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By J. Abdollahisharif

Optimal cut-off grade is one of the most critical parameters in open-pit mine design because it defines the ore and waste and thus determines the maximum net present value possible from the mining operation. Although the algorithm presented by Lane (Choosing the optimum cut-off grade. Colorado school of Mines Quarterly, vol. 59, no. 4, 1964. pp. 811-829) is the most common one in the literature, it does assume constant capacities of the mine, processing, and refinery. In this paper, Lane's original algorithm has been modified to consider variable processing capacities in order to determine the optimal cut-off grade in open-pit mines. The new algorithm proposed here is compared to both Lane's original algorithm and to a previous modification that incorporated rehabilitation costs into the cut-off grade estimation. The algorithm proposed here that permits variable processing capacities is shown to be superior for the determination of optimal cut-off grade to both these previous versions. In addition, a computer-based program was developed in Microsoft Office Excel© to calculate the optimal cut-off grade as proposed here.

Jan 1, 2012

By A. M. Engelbrecht

Paper written on project work carried out in partial fulfilment of B Eng. (Chemical) Membrane processes are vital to a diverse range of technical and biological systems, which also feature in mineral processing applications such as the treatment of mine effluent and extraction of metals. In this study, the use of cellular automata to model a semi-permeable membrane that separates two compartments is considered. Cellular automata are simple models that enable the analyst to represent well-understood local effects, such as the chemical or steric interaction between molecules themselves and between molecules or particles and their environment, which can lead to very complex behaviour on a macroscopic scale. Various physical phenomena, including reverse osmosis, were simulated. Initial results for the effect of temperature, membrane structure and chemical properties of the solutes on the performance of the membrane appear promising. Keywords: cellular automata, dynamic modelling, filtration, membrane fouling, osmosis.

Jan 1, 2007

By W. K. Osae

A value assessment model which uses deal objectives, financial and non-financial indicators as a guide to assess value creation in mergers and acquisitions. The extent to which post- merger deal objectives are achieved and the potential benefits derived from mining deals that may not necessarily be financial of nature, but which are necessary to sustain and enhance future performance, were considered. The pre-merger and post-merger performances based on some financial indicators that reflect profitability for shareholders were also used. This value assessment model was used to assess four major deals that have occurred in the South African mining industry since 2003 as part of a postgraduate dissertation. In this paper, the Harmony and ARMgold merger is used as an example of how the model can be applied. The model?s relevance and applicability can also serve as a guideline in developing a framework or holistic guideline in assessing whether mining BEE deals in South Africa create value.

Jan 1, 2011

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixture of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of a stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2006

By S. Gqebe, A. Lewis, M. Rodriguez-Pascual

"Gravitational sedimentation of suspensions in various precipitation processes is hindered by colloidal stability. This is due to the high surface charge of the suspension and results in strong attraction/interaction between the ions on the particle surface and counter-ions in solution. Moreover, this strong interaction results in a charge build-up that renders the suspension stable. In order to induce gravitational sedimentation of these particles, a redistribution of ions close to the particle surface is required. We therefore sought to redistribute ions close to the particle surface by applying a magnetic field. This results in the reduction of interparticle electrostatic repulsive forces and a subsequent increase in the zeta potential of a suspension. For the purpose of this study, a copper sulphide suspension was used. Copper sulphide particles were exposed to a range of field strengths for set exposure times and their zeta potential was measured before and after exposure. All particles had an initial zeta potential value equal to or less than –40 mV prior to magnetic field exposure. A significant increase in zeta potential was observed, with values reaching a maximum of –16.5 mV when exposed to a 2 T field strength for 40 minutes. This is due to Lorentz ion shifts resulting from the Lorentz force exerted by the magnetic field on the particle surface. IntroductionMetal sulphide precipitation is a process for treating industrial waste streams with high residual concentration of mixed metal ions and acid mine drainage. This process has been reported to achieve higher metal removal compared with the industrially prevalent lime precipitation, due to the sparingly soluble nature of the metal sulphide precipitates formed. However, precipitation is governed by high levels of supersaturation which favour the formation of fine particles (Lewis, 2010). Consequently, some of the metal sulphide fines formed exhibit slow settling dynamics and thus tend to remain suspended in solution."

Jan 1, 2016

By H. F. Fuls

Skorpion Zinc, an integrated zinc mine and refinery located in the south of Namibia, has a production capacity of 150 000 t/a of special high grade (SHG) zinc. The Skorpion zinc oxide resource will be depleted by 2017. Extensive exploration drilling for additional zinc oxides was conducted without success. With the abundant availability of zinc sulphide concentrates regionally (Black Mountain and Gamsberg in the Northern Cape or Rosh Pinah Zinc and new deposits in the Rosh Pinah region) the life of the operation can be extended by processing of zinc sulphide concentrates. The leach kinetics of zinc sulphides is vastly slower than for oxides, preventing the processing of zinc sulphides in the existing process under current conditions, and Skorpion Zinc faces the challenge to identify a suitable zinc sulphide treatment process that can be integrated with the existing plant. Various zinc sulphide processing options were identified through an extensive literature search and non-viable options were eliminated. Mass and energy balances were established for potential options and an economic evaluation (including capital and operating cost estimation) was conducted to identify a suitable process. It is concluded that ferric leaching of sphalerite in a sulphate medium under atmospheric or pressure leach conditions are suitable processes for Skorpion Zinc. These processes present advantages over all other zinc processing options when elemental sulphur is preferred as the final deportment for sulphide sulphur. Both these processes can be integrated into the existing refinery and will be able to process concentrates with a wide composition range.

Jan 1, 2013

By L. A. Cramer

There are a couple of dozen junior platinum mining companies coming into existence in Southern African and most intend to mine, concentrate the PGM?s in a flotation product and sell the concentrate to one of the major producers in South Africa. The price they will receive for their product and hence the return they achieve for their investment will depend upon the large number of factors that influence the market for such a product. Unfortunately the number of buyers is severely limited as it is dominated by the two major local producers, Impala Platinum and Anglo Platinum. Furthermore the current smelting technology has limited capacity for UG2 concentrates and high nickel concentrates will quickly fill any available base metal refining capacity. Few if any overseas buyers can compete for the bulky flotation concentrate produced. This paper will explore those factors such as metal recoveries, metal prices, operating costs, capacity constraints, deleterious elements, transport issues, metal premiums and discounts that are in play, types of flotation concentrates, processing capital costs, PGM grades, etc and their impact up on what smelters and refiners might be prepared to pay for such PGM concentrates. Ultimately simple graphs and equations can be developed for probably payment terms for such concentrates. Those who negotiate well will move to the higher return section of the envelope and those who use the concentrator facilities to produce the most saleable combination of flotation concentrates will enhance their returns. A deep and firm understanding of the issues surrounding this market is necessary in order to negotiate the best possible price for the seller.

Jan 1, 2008

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019