Search Documents

By W van Drunick, S Naik

To date, Anglo Research has carried out several projects, based on the techniques developed in the AMIRA P9 (AMIRA International Limited), to develop comminution and flotation models for several Anglo Base Metals and, to a lesser degree, Anglo Platinum flotation plants. Plant optimization is thus achieved through steady-state sampling, model-fitting and simulation using the JK SimMet and JK SimFloat software packages. The surveys can vary depending on the needs of the plant/client. The survey can therefore include as little as a single piece of equipment, an entire milling/flotation circuit, or a complete circuit from primary comminution to final flotation concentrate (i.e. the ?integrated survey?). The presence of the AR team on-site usually precipitates in face-value observations that can lead to initial improvements. This stems from the knowledge-sharing on best practice that exists in parallel with the surveys. Numerous (reasonable) changes can then be simulated, thus indicating the optimization step most likely to result in the best efficiency improvements. The simulations can include changes in the flowsheet, ore characteristics, mill loads, grinding media size, change in grind, flotation residence time, air hold-up and several more. Plant surveys can result in process changes that provide the plant with either: higher plant tonnage, improved plant grind, additional flotation recovery and/or improved product grade. The additional benefit of performing an integrated plant survey is that the effects of an optimization change in the comminution circuit can be simulated using the flotation model. This paper describes a number of case studies where individual and integrated plant surveys were conducted by AR for Anglo Base Metals.

Jan 1, 2007

By P. S. Piper

In the 1960s it was suggested that the volume of stope convergence, and hence the rockburst hazard, could be reduced by the emplacement of backfill. Recent advances have facilitated the placement of large quantities of backfill underground, and a reassessment of its potential benefits as part of a regional support strategy is now timely. In this paper the principal criteria of effectiveness of backfill are taken to be its impact on face energy release rate (ERR) and average pillar stress (APS) levels, and maximization of acceptable ore extraction ratios. The possible effects of backfill on excess shear stresses (thought to modulate large seismic events) are also briefly reviewed. Analytic solutions describing backfill properties and their impact on ERR and APS in certain idealized geometries are also presented, and compared with the results of an extensive suite of computer simulations, in which parameter sensitivities are explored. Results indicate that a regional support strategy is required at depths exceeding 2 km in order to maintain acceptable levels of ERR, and backfill ribs can on their own fulfil this role at depths less than 3,3 km. At greater depths use of stabilizing pillars becomes imperative, but here too supplementary backfill ribs can reduce ERR and APS levels and permit significant increases in ore extraction ratios.

Jan 1, 1988

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world&apos;s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of 160-250 Mt; however, all previous attempts to extract the PGE from this ore type have proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas the arsenide- and sulphide-PGMs that make up approximately 25 per cent of the original Pt content of the ore largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd) -oxides or hydroxides, or in iron-hydroxides, Mn-Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2013

By J. W. Neale

Mintek was a leading participant in the BioMinE project between 2004 and 2008. This project, which was funded in part by the European Commission, was aimed at the development of biotechnology for the minerals industry in Europe. Mintek?s research programme focused mainly on the development of integrated bioleach-based processes for the recovery of base metals from complex, low-grade sulphide concentrates. Specific European mineral resources were targeted and used in integrated piloting campaigns involving bioleaching, solution purification, and metals recovery. This paper describes the use of thermophilic bioleaching for the recovery of nickel and copper from a low-grade nickel-copper concentrate produced at the Aguablanca Mine in southern Spain. Currently, the Aguablanca Mine produces a bulk nickel-copper concentrate for sale to a smelter, and the proposition is to increase the profitability of the operation by the on-site production of metal or metal intermediate. Initially, bench-scale bioleach tests were conducted to determine the bioleach operating conditions. These tests included an evaluation of mesophilic, moderately thermophilic and thermophilic microorganisms. In order to achieve sufficiently high levels of both copper and nickel extraction, a thermophilic process was selected?this was necessary for leaching of the refractory chalcopyrite that occurs in this concentrate. Additional bench-scale test work was carried out to derive a conceptual process flowsheet for the solution purification and metals recovery circuit. The results of the bench-scale tests were used to design, construct and commission an integrated pilot plant, which was subsequently operated at Mintek for over seven months. During this time, the solution purification and metals recovery processes were optimized, and all recycle loops were closed. The final process flowsheet included the following unit operations: concentrate regrinding, thermophilic bioleaching at 70°C, primary iron removal using limestone, copper solvent extraction and electrowinning, secondary iron removal, nickel hydroxide precipitation using magnesia, and final solution purification using lime. Where applicable, process solutions were recycled to preserve water. The process design data derived from this pilot-plant campaign formed the basis for a conceptual engineering study for the developed process. In the study, mass and energy balances were derived, and a process flowsheet was developed and used as the basis for estimating the capital and operating costs of the process. This enabled a preliminary economic analysis of the process to be undertaken. The findings of this study are discussed.

Jan 1, 2009

By B.E. Hall

Maximizing shareholder value has become a common aim for mining companies. This paper discusses the results of a number of studies developing strategic mine plans, covering a wide range of commodities, styles of mineralization, mining methods, and processing facilities, for single and multiple deposits. It has become evident that traditional methods and conventional wisdom often do not in fact achieve these goals. Operating policies at many mines ensure that shareholder value is not maximized. Changing the overall strategy can provide significant value gains. Typically, the new optimal plan involves a significant increase in the cutoff grade, at least in the earlier years. An increase in the underground development rate or open cut stripping rate is often associated with this, at least in the short term, to establish the new strategy. Cost minimization is found to be counter-productive. Counter-intuitive plans are often found to be optimal. For example, optimal cutoffs for different parts of an underground mine may be significantly different, even if mineralisation and cost structures are similar. Sub-optimal strategies are also frequently found to have a significantly greater financial risk than optimal plans, which have been found in many cases to be relatively insensitive to changes in major value drivers, such as metal prices. This paper shows how identifying and then operating within the framework of an optimal strategic plan can have substantial benefits over being continually driven by short-term tactical issues.

Jan 1, 2009

By A. Pytlik, W. Masny

"Underground mining is subject to various natural hazards such as seismic events, rockbursts, fire, and gas (methane). In general, an increase in the extraction depth causes an increase in the likelihood of these hazards, especially seismic activity and rockbursts. Dynamic phenomena such as rockbursts and tremors have been recorded on six continents: Europe (Poland, Russia, Czech Republic, Germany, and Slovenia), Asia (India, and China), North and South America (USA, Canada, and Chile), Africa (South Africa), and Australia. To select appropriate mine working supports for such dynamic phenomena, the performance characteristics of such support types must be determined under both static and dynamic load conditions.This article presents information regarding the application of rockbolts in Polish underground hard-coal mines. Dynamic phenomena occurring in the mines from 2004–2013 are also characterized. A methodology developed at the Central Mining Institute (GIG) for the laboratory testing of rockbolts is presented. In this methodology, the bolts are loaded by the direct impact of a free-moving mass (up to 20 000 kg) at speeds of up to 1.2 m/s. The facilities at GIG used to test the support under static and dynamic load conditions are characterized, and the results of laboratory tests on yielding bolts with a nominal capacity of 420 kN are presented. These types of bolts are commonly used for reinforcing steel arches and the surrounding rock mass in Polish coal mines. The results of the laboratory testing of yielding bolts are discussed.IntroductionSeismic events such as rock bumps and tremors occur with great frequency during underground mining. These phenomena have been reported in such countries as Poland, Czech Republic, Germany, France, Slovenia, Russia, India, China, the USA, Canada, Chile, South Africa, and Australia (Brauner, 1991; Potvin, Hudyma, and Jewell, 2000; Kidybin??ski, 2003; Driad-Lebeau et al., 2005; Li, Cai, and Cai, 2007; Whyatt and Loken, 2009; Durrheim and Riemer, 2012; Holub, Rušajova, and Holec?ko, 2011). Descriptions of the dynamic events and their effects in the form of damage to or destruction of supports have been presented in many publications, both for hardrock mines as well as for coal mines (Brauner, 1991; Dubin??ski and Konopko, 2000; Heal, 2010; Heal and Potvin, 2007; Simser, Joughin, and Ortlepp, 2002; Kaiser and Cai, 2012; Cai 2013; Nierobisz, 2013; Mark, 2014; Masny and Prusek, 2015). One of the main goals of the research has been to develop methods, criteria, and guidelines for the selection of an optimal and safe support for mine workings located in areas of rock bumps or tremors. Example of such studies include the Canadian Rockburst Support Handbook (Kaiser, McCreath, and Tannant, 1996), or the principles presented in the literature (Li, 2010; Cai, 2013)."

Jan 1, 2016

By H. Moslemi

Metal sulphides are usually semiconductor and their electrical conductivity is low; therefore they are sources of electrons and promote electrochemical reactions. This phenomenon is of significant importance in sulphide flotation. The formation of a hydrophobic surface on the sulphide minerals is the result of various electrochemical reactions. Potential difference in the mineral-liquid interface plays an important role in the kinetics of the reactions, and consequently, on the flotation behaviour of sulphides. The value of the potential difference is influenced by different oxidation-reduction reactions at the interface area, and is measured by a two-electrode system in which an electrode is applied as reference electrode. In this study, we attempted to measure open-circuit potentials of pyrite, pyrrhotite, and steel electrodes with respect to the reference electrode. To verify the results, two reference electrodes, saturated calomel and gold, were used. Time-potential relations with respect to both reference electrodes show that the potential of both pyrite and pyrrhotite increases with time; however, this trend decreases for steel except when at pH 12. The results show a potential drop by an increase in pH value, except for steel, for which the opposite holds. This paper discusses galvanic interactions between minerals and grinding media in the grinding circuits, as well as among other minerals in the flotation processes.

Jan 1, 2012

By M. D. Raganya

The Kriel Colliery is an Anglo Coal mine which is contracted with Eskom to produce No. 4 seam for Kriel power station. The mine previously found it uneconomical to mine No. 5 seam due to the low qualities and tonnages of the seam, both at the opencast and underground sections. An area has been encountered for the first time at Kriel Colliery opencast pit 5, where the tonnage and qualities of No. 5 seam warrant further investigation. The primary reason for the investi¬gation of No. 5 seam by Kriel Colliery is because of the advantage of the high selling price (R450/t) that the market is currently prepared to pay for the No. 5 seam. The aim of this project is to mine No. 5 seam economically without interrupting No. 4 seam mining operations. The problem is that the equipments that are currently being used at the mine belong to Eskom and are dedicated to mining No. 4 seam only, not No. 5 seam. Through geology investigation, it is found that the whole No. 5 seam (No. 5 seam upper and lower) has an average thickness of 1.8 m. It also contains a parting of carbonaceous shale which divides the seam into two parts. No. 5 seam upper contains less tonnage compared to No. 5 seam lower. The calorific value and ash content of No. 5 seam lower is far better than No. 5 seam upper, but would still require washing the coal. This makes No. 5 seam lower the preferred seam to mine because it meets the requirements of the customer which is Highveld Steel. It is a coincidence that the area containing No. 5 seam under investigation encounters high overburden problems. The problem of drilling to No. 4 seam was going to be encountered because the thickness of the overburden ranges from 35 to 39 m. The Gardner Denver at the mine can drill blastholes only to a depth of 34.5 m, meaning the full overburden will not be drilled at once. This means the mining of No. 5 seam will do favours for Eskom because the overburden thickness will be minimized. This then led to an agreement between Anglo Coal and Eskom to mine No. 5 seam because both companies benefit from the project. In order to identify a suitable mining method for No. 5 seam lower, literature studies took place. It is found that San Juan mine from the USA has similar geological features to Kriel Colliery&apos;s No. 5 seam. Through comparisons, it is found that truck and shovel mining would suit the geology of Kriel Colliery&apos;s No. 5 seam since San Juan mine is using it. The sequence of mining No. 5 seam lower allows for a clearance of two cuts between the truck and shovel operation and the dragline. The mining sequence of No. 5 and 4 seam will be in the order of top soil removal; soft overburden pre-stripping; pre-strip drilling; pre-strip hard overburden; No. 5 seam lower coaling; interburden drilling and blasting; interburden stripping and No. 4 seam coaling. Financial evaluation of the project shows that a contractor will charge Kriel Colliery (Anglo Coal) approximately R 102.2 million to mine No. 5 seam successfully. The sales of No. 5 seam lower will provide a profit of R99.4 million at a yield of 70% from the washing plant. The project is beneficial to both Eskom and Anglo Coal because Eskom will have eliminated the problem of pre-stripping and Anglo Coal will generate additional profit. Through investigation and analyses of the project, it is proven to be viable and should take place. This is after looking at the advantages that the project has for Anglo Coal and Eskom. Keywords No. 5 seam, truck and shovel mining, Kriel Colliery, No. 5 seam mining at Kriel Colliery opencast, Anglo Coal and Eskom, No. 5 seam upper and lower, top soil removal, soft overburden pre-stripping, pre-strip drilling, pre-strip hard overburden, No. 5 seam lower coaling, interburden drilling and blasting, interburden stripping, No. 4 seam coaling.

Jan 1, 2011

By Paul Fouchè, Danie van der Merwe

Contents ?Purpose ?Introduction ?Development of RF tracers ?Test procedure ?Results ?Conclusion ?Way forward ?Acknowledgements

Jan 1, 2005

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By A. Della Rocca, P. Jonker, B. Henning

Successful prediction of the collection efficiency of cyclone separators is a necessary step in cyclone design and verification. Aside from standard empirical relations, CFD modelling is widely adopted to supplement the design of cyclone units in relation to the desired separation performance. Nevertheless, effective adoption of numerical modelling is sometimes prevented by large modelling errors, especially for small size particles which are more subject to turbulence effects than larger particle classes. In the past, this motivated the adoption of more refined turbulence modelling approaches, such as large-eddy simulations. These approaches provide greater insight into time dependent behaviour, while leading to larger computational cost with respect to more standard approaches. In this paper, an effective Eulerian-Lagrangian Reynolds-averaged Navier-Stokes (RANS) approach is investigated, which is able to predict the complete separation efficiency curve with satisfactory accuracy, without requiring prohibitively long computational times. An assessment of the proposed approach is carried out against experimental data from large laboratory scale cyclones, in the form of mean and fluctuating velocity profiles from LDA measurements (Hoekstra, 2000), as well as with respect to the experimental separation curve (Zhao, 2005). The final application to a full-scale industrial cyclone unit is then carried out with the aim of tuning the cyclone design to the separation efficiency curve as required by downstream processes. Keywords: Cyclones, separation, CFD, RANS, RSM, Lagrangian

Jan 1, 2020

By J. W. Drelich, H. Zeng, L. Xie, X. Cui, Z. Gao, M. Tian, Y. Hu, W. Hu, W. Sun

Flotation is a mineral separation technology that uses the surface hydrophobic difference of valuable minerals and their associated gangue minerals to separate them. The flotation collector adsorbs on the valuable mineral surface to improve its hydrophobicity, and metal ions are usually used as activators to enhance the collector adsorption. Different mineral surfaces show different charging properties and adsorption behaviours with the collector or metal ions. Moreover, the order of adding metal ions and the collector also show significant and different flotation performance for the same mineral. The adsorption or flotation behaviour or both are governed by mineral surface chemistry, such as surface charging and reactivity. In our recent studies, force measurement using atomic force microscopy (AFM) was employed to study the surface charging and adsorption mechanism of metal ions and collectors. By preparing collector-functionalised AFM tips, AFM can directly measure the adsorption strength of the collector on the mineral surface to determine the anisotropy of mineral surface reactivity. The preparation of collector-functionalised AFM tips provides the foundation for further study of the activation role of metal ion in the collector adsorption. The application of AFM for force measurement in the surface chemistry of mineral flotation can provide important information on developing flotation reagents and lays the foundation for the specific regulation of mineral surface characteristics. Keywords: Scheelite; flotation; surface chemistry; AFM force measurement

Jan 1, 2020

By G. R. Sawyer

Although backfilling has been in operation for many years, the methods for selecting appropriate slurry dewatering aids have, in some cases, been rather unsophisticated. This has led to many misconceptions regarding the role of the dewatering aid and its various means of application. Testing procedures employed in the correct selection of any practically applied dewatering aid must mirror the actual working processes in which they are to be used. This constraint necessitates the development of complex testing methods when applied to backfilling. The current testing procedures were scrutinized and their various merits noted. From this study a series of testing methods was evolved which incorporate the best aspects of these testing procedures with novel ideas which would eventually result in the correct selection of the dewatering aid. A major consideration in the application of any of these methods is the modus operandi of the backfilling process, and the relevance of the tests to the process. This work attempts to consolidate the testwork performed in the past and suggest new approaches in the correct selection of acceptable dewatering aids for backfilling.

Jan 1, 1988

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By R. G. B. Pickering

The South African narrow reef hard rock mining industry has been stuck in a time warp with relatively little change in the mining process in the last century. This paper presents a methodology on how to implement change in narrow reef hard rock mining. It then explores a number of technologies that have been introduced into this mining industry and the impact that they have had on the mining process. The author then presents his view on whether the defined change process has been followed and sets out to identify the most critical aspect of ensuring that change is successfully implemented. Future demand will also be speculated on.

Jan 1, 2007

By D. Visser

This paper is based on the Townlands Ore Replacement Project whereby the concept of conventional sinking of one large diameter shaft was declined and replaced with three smaller raise bored shafts. A wire line geophysical survey was done and the results indicated that a single shaft larger then 4 m diameter unsupported would not be suitable. The shafts were placed 28 meters apart measured from centre to centre. To ensure that the skin to skin pillars between the shafts remained regular and to minimise any deflection, the pilot holes were drilled with the Rotary Vertical Drilling System. The different shaft sinking methodologies are discussed explaining the risk associated with each method.

Jan 1, 2009

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008