Search Documents

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By IRENE AITKENS

The Mining Law of 1910 , with amendments of 1914 and 1928 , is at present in force in the Dominican Republic . The first and basic mining law of the Republic was passed in 1876 , and although numerous changes and amendments have been made from time to time , the new laws and amendments thereto have not changed the original or basic law materially . However , these enactments have materially changed the legal methods governing the exploitation of the mineral resources of this country and have added new regulations and requirements to those concerning certain specific minerals , etc. The original or basic law still exists as it was first promulgated to protect the rights of the Dominican Republic itself , the rights of the landowner , and the rights of prospectors in general . The Mining Law of 1876 remained in force , without amendment , until it was superseded by the law of May 25 , 1904 , an enactment modeled after the Mexican mining law and designed especially to encourage the investment of

May 1, 1931

Jul 1, 2003

Tables

Jan 1, 1992

The use of highwall mining systems (Figure 1) has increased substantially in open-pit coal mines. It is used where overburden depth exceeds economical recovery. Highwall stability remains the major safety concern during highwall mining. The Mine Safety and Health Administration requires highwall mining operators to follow ground control plans that specify the pillar sizes necessary to prevent a pillar collapse that would threaten highwall stability.

Mar 1, 2006

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified.

By W. F. Hughes

The thermodynamics of an electromagnetic field-fluid interaction system is discussed. A review of the thermodynamics of linear media (the permittivity and permeability taken as functions of density and temperature) is presented; then an extension is made to nonlinear media (the permittivity and permeability taken as functions of the fields). Expressions for thermodynamic properties and reversible work are derived and the first law of thermodynamics for magnetohydrodynamic flow is discussed.

Jan 1, 1968

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973

By Howard E. Parkinson

Since 1969, the Department of Interior, Bureau of Mines, has carried out communications research. Research has been directed toward developing emergency and nonemergency mine communications. This paper gives an overview of the progress made in the last two years. Particular emphasis is given to the overall program, noise and signal measurements, systems studies, guidelines, products, and demonstrations now being carried on in operating mines.

By Arthur E. Goddard

Radio propagation measurements were conducted in a coal mine at UHF (200 to 1000 MHz) and VLF (1 to 50 kHz) to characterize the transmission loss of intra-mine paths. The basic experimental parameters included frequency, polarization, path orientation and distance. Further tests evaluated the performance of roof-bolt vs. loop antennas at VLF and parasitic reflectors at UHF. Measurement results are summarized in a series of transmission loss curves. Examples are presented to show the use of these curves in predicting the performance of radio communication systems in mines.

Jan 1, 1973

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

By Fred C. Turin, Kim M. Cornelius

Work in underground coal mines is repetitive and physically demanding. Workers commonly report a wide range of aches and pains. Management at one mine was concerned about increased reporting of aches and pains by roof bolting machine operators. An analysis of roof bolting tasks was conducted at this mine to identify early warning signs of cumulative trauma. Health and safety risk factors were identified and recommendations to reduce cumulative trauma exposure were provided. Recommendations addressed job procedures, equipment design, and worker awareness of risk factors.

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By Kenneth L. Cashdollar

While underground coal technology has progressed over time, regulations on coal dust have not kept up ? the most recent rules are more than 80 years old. The National Institute for Occupational Safety and Health and the Mine Safety and Health Administration conducted a joint survey recently on coal particle ranges as measured in US coal mine samples. In underground coal mines, dust explosions are prevented by the addition of enough rock dust (usually limestone) to make the total dust mixture inert. The rock dust acts as a heat sink for the dispersed dust mixture by reducing the temperature below the value needed to propagate an explosion. Federal regulations require 65% in combustible content in intake airways and 80% incombustible content in return airways, where the coal dust is assumed to be finer in size. The regulations also require an additional 1% incombustible for each 0.1% methane in the ventilating air in intakes and 0.4% additional incombustible for each 0.1% methane in returns.

Jan 1, 2008

By Thomas V. Falkie, R. Venkataramani

The method of analysis was to test a large model containing potentially significant variables and on the basis of the results obtained, to reduce the model to one containing only the essential significant variables. This stepwise procedure of "scanning" a large proposed model and subsequently condensing the model consisted of two cycles of the same series of computational procedures. Data Preparation A majority of the variables measured were continuous over a specific range of values; for example, the variable "Width Ratio" varied in practice from 0.25 to 1.00. However, "dummy" values were assigned to certain operational variables in order that these varia¬bles would have numerical expression. The following variables were described in this manner. Variable "Dummy" Value x3: Development/Pillaring 0, if pillar extraction was being done 1, if development mining was being done x4: Boxcut/Open Cut 0, if a box cut was being made 1, if an open cut was being made The variables under consideration are represented symbolically as follows: Y: Loading rate (tons per minuts): TONS/MIN x1: Ratio, width of cut/width of cutter: WDRATIO x2: Ratio, height of cut/diameter of cutter: HTRATIO x3: Development or pillaring: D/P

Jan 1, 1972

By Charles L. Kimbell

This study is intended to serve three roles. First, it is an extension of the previous works under the same title that have been the overview and summary chapter of the international volume of Minerals Yearbook since the inception of that volume. Following the traditional format of past chapters, the basic statistical presentations herein deal chiefly with 1989, and in some instances with 1988, the latter only because more recent, comprehensive global statistics for 1989 are simply not yet available owing to delayed data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world&apos;s mineral industry that have occurred between the end of 1989 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1992