Search Documents

By E. C. Bennett

"INRTODUCTIONVarious methods of making leakage tests have been tried during a study of losses in the transmission of natural gas. This work has been carried on by the Bureau of Mines in cooperation with the Natural Gas Association of America. Results of torts show that the ""shut-in -pressure-drop"" method described by Rawlins is the most accurate and reliable; therefore its use is recommended. This paper describes a graphic method for computing the rote of leakage from the fall in pressure and change in temperature determined by the ""shut -in pressure-drop"" method of testing.METHOD OF MEASURING PRESSURE DROPThe gas is ""shut in"" line to be tested and is not allowed to escape except through existing leaks. The leakage causes the pressure in the line to fall. The charge in pressure is obtained with a dead weight gage. Approximate results may also be obtained from readings on a good spring test gage. Numerous tests show that the dead weight gage is more sensitive to small changes in pressure than spring gages.The temperature of the gas in the line is observed simultaneously with each pressure reading. Temperature changes affect the pressure exerted by a given quality of gas ""shut in a line, end since the rate of leakage from a closed system is directly proportional to the rate of pressure drop, fluctuations in temperature must be considered."

May 1, 1926

By J. M. Stuve

The standard heats of formation (?Hf°) of holmium trichloride and terbium trichloride were measured by solution calorimetry. Heats of solution of holmium and terbium metals and their anhydrous chlorides were measured in 4.360 molal HCI at 298.15° K. From these measurements ?Hf° for HoC13 (c) was calculated as -240,290 ±1,700 cal/mo1e, and ?Hf° for TbC13 (c) was calculated as -238,330 ±1,500 cal/mole at 298.15° K.

Jan 1, 1967

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By M. J. Ferrante

High-temperature enthalpy and X-ray powder diffraction studies were con-ducted on aluminum sulfide (Al2S3) as part of the Bureau of Mines effort to provide new data for the advancement of mineral technology consistent with environmental preservation and energy conservation. Relative enthalpies were measured with a copper-block calorimeter from 298.15 to 879 K. Tabulated values are listed for heat capacity, entropy, Gibbs energy functions, and relative enthalpies between 298.15 and 900 K. Enthalpies were also given in the form of an equation and combined with published data to calculate standard enthalpies of formation and Gibbs energies of formation for reactions of crystalline aluminum with crystalline, liquid, and gaseous diatomic sulfur. The hexagonal, rhombohedral, and cubic phases of Al2S3 were identified by X-ray powder diffraction studies, and the indexed powder diffraction patterns of these phases are given. The hexagonal phase was stable to about 852 K and was partially converted to the rhombohedral form at 879 K.

Jan 1, 1981

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By P. Coleman, J. C. Kerkering, S. Iverson

Fault tree analysis is a systematic safety analysis tool that proceeds deductively from the occurrence of an undesired event (accident) to the identification of the root causes of that event. One recurring mine safety problem—a dozer falling into a void over a drawpoint on a coal surge pile—was analyzed using available, inexpensive fault tree programs on a personal computer. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between these various subordinate events as well as the various chain of events leading up to the primary event. A sensitivity analysis on these probabilities showed which events had the greatest influence on dozer burial in a coal surge pile.

Produce an annotated bibliography to serve as a comprehensive source of published information available on the use of soil amendments in coal mine reclamation and the characterization of coal mine soils. The Problem There is a substantial amount of information available tin coal mine reclamation and revegetation, particularly on the use of soil amendments to ameliorate site conditions and aid vegetation establishment, growth development, and productivity. Additionally, site characterizations based on chemical, physical, and mineralogical properties have been thoroughly researched. This information, however, is widely disseminated throughout various professional and scientific journals, State and Federal documents, proceedings of conferences, theses, and other technical writings. A critical need exists for a comprehensive and up-to-date summary of published information concerning the uses, methodologies, and types of soil amendments that arc necessary for reclamation success.

Jan 1, 1991

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society's interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By W. W. Adams

"Fatal accidents at coal mines throughout the United States killed 234 employees during January 1924, according to reports from State mine inspectors to the Bureau of Mines of the Department of the Interior, Included in the number of fatalities are 68 deaths caused by two explosions during the month, one explosion occurring in a mine at Johnson City, Ill., and causing 32 deaths, and the other in a mine at Shanktown, Pa., and causing 36 deaths. The fatality rate for the month was 3.94 per million tons, based on a production of 59,435,000 tons of coals In January 1923 the fatality rate was 3.52, based on 206 deaths and an output of 58,458,000 tons.Bituminous mines in all States reported 202 fatal accidents, the production being 51,170,000 tons., and the fatality rate being 3.92, as compared with 3.28 for January last year, For the anthracite mines in Pennsylvania, the reports covered 32 fatalities, which, on the month's output of 7,955,000 tons, indicated a fatality rate of 4.02 per million tons, as against 4.89 for January 1923.As compared with January 1923, the reports for January of the present year indicated lower fatality rates per million tons for all of the main causes of accidents except explosions. For falls of roof and coal, the fatality rate per million tons declined from 1.85 in January 1923 to 1,68 in January 1924; for haulage accidents the rate declined from 0.62 to 0.42; for explosives, from 0.19 to 0.12; for electricity, from 0.12 to 0.07. The rate for explosions increased from 0.21 to 1,31 per million tons. -- Reports of Investigations, Department of the Interior, Bureau of Mines."

Feb 1, 1924

By George H. Ashley

Character The bituminous coals of Pennsylvania range from low volatile to high volatile, but are all low moisture coals The coals are of three types caking of coking, noncaking or splint, and cannel The percentage of volatile matter in all kinds changes from low at the east to high at the west This change is thought to be due to the pies sure and folding to which the coals along with the other rocks have been subjected In the Broad Top field, and in Somerset, Cambric, Clearfield, Centre, and other counties to the northeast, most coals contain from 3 to 5 times as much fixed carbon as volatile matter, the fixed carbon ranging from 67 to 75 per cent, and the volatile mattes from 16 to 24 per cent These coals are classed as lovol coals In the line of counties just west of those listed the coals are of the medium volatile class (midvols) This includes the famous Connellsville coking coal Still farther west, covering most of Washing ton and Westmoreland counties, and the counties to the north of them are high volatile coals of gas coals (hivols) This is discussed in Part I on the geology of the coals of Pennsylvania, where is given in isocaib map Cannel coals ale found in many par is of the bituminous coal field of Pennsylvania, but in particular in Beaver Butler, Armstrong, Indiana, and Clear field counties The cannels of Beaver and Butler. counties are typical high volatile cannels, many of which have been used in times past for oil distillation The cannels of Armstrong and Indiana counties are medium volatile cannels, and while main taming the physical character of cannels, have no more volatile neat ten than the coals around them The cannels of Clearfield County tie low volatile Splint coals of noncakmg coals are not abundant in Pennsylvania. The Sharon coal, formerly mined in Mercer County, was a noncaking or splint or block coal, and was formerly used in the raw state in non smelting Uses STEAM COAL Practically all of the coals of Pennsylvania are steam coals, though many coals in the Commonwealth, because of high ash, are not good steam coals The coal of the Pittsburgh district has long been famous

Jan 1, 1928

By Edward D. Thimons, Jay F. Colinet

Underground coal mining operations in the United States continue to increase productivity as mining equipment and practices are improved. Unfortunately, increased production also results in the potential for increased respirable dust generation and worker exposure. In response, US operations are applying basic controls at elevated levels and looking to emerging technologies in an effort to better control respirable dust levels. Ventilating air and water sprays remain the basis of dust control strategies for both longwall and continuous mining operations, and the level of application for these controls continues to increase. In addition, new technologies are emerging that have the potential to further reduce dust levels. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research into methods to optimize existing control technologies and evaluate emerging control technologies. This paper will summarize control technologies routinely being used in underground coal mine operations, as well as provide a review of new controls that are being pursued.

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.

To rapidly and dependably locate shorts and opens in mining equipment power cables. Approach: The approximate locations of faults are found using a sound pulse echo, then the faults are exactly located with one of two probes. How It Works: To approximately locate u fault in shielded or unshielded cable, the cable is disconnected from the mine power center, and connected to the sound pulse generator. The generator is also connected to the ground conductor of the cable. When the generator is energized, electrical pulses are transmitted, and each moves along the conductor until it reaches a fault. When a pulse reaches the fault an echo returns to the instrument, either a positive pulse if the fault is an open, or a negative pulse if the fault is a short. See Figure 1. The further along the cable the first fault is from the instrument, the longer it takes for the echo to return. The instrument automatically measures the time and calculates the distance. The distance in feet is shown on an illuminated digital display.

Jan 1, 1976

Provide the U.S. mining industry with the means to measure and control exhaust emissions of diesel engines used in underground mines. Approach Diesel research is divided into four primary areas: exhaust aerosol measurement, particulate control, gaseous emission control, and chemical and biological characterizition of particulate matter. Diesel research is frequently cosponsored by industry; collaborative research ventures between industry, academia, other government agencies, and the Bureau arc common. Diesel research at the Bureau is conducted in the diesel engine research facility at the Bureau?s Twin Cities Research Center (TCRC). This facility is a state-of-the-art laboratory capable of performing emissions testing, exhaust control evaluations, and safety tests. Background Exposure of mine workers to airborne contaminants from diesel engine exhaust is potentially harmful. The National Institute for Occupational Safety and Health has recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen" and that ?reductions in exposure to diesel exhaust in the workplace would reduce the risk." The U.S. Mine Safely and Health Administration (MSHA) convened an Advisory Committee on Standards and Regulations for Diesel-Powered Equipment and is beginning to implement its recommendations, which cover health, safety, and certification and approval issues surrounding the use of diesels underground. In January 1992, MSHA published an advance notice of proposed rulemaking to regulate diesel particulate matter in underground mines.

Jan 1, 1992

By Forrest T. Moyer

OVERALL data for 1963 on injury experience and the levels of employment, worktime, and operating activity of the mineral industries are shown in the statistical tables of this chapter. The general groupings of the industries are presented in greater detail in Volumes I and II of the Minerals Yearbook. A corresponding chapter in Volume I contains additional breakdowns of the data on metal, nonmetal, sand and gravel, slag, and stone mines and quarries together with separate information on the related processing mills and plants including primary nonferrous smelters. The more specific information on the anthracite and bituminous-coal, petroleum and natural gas, peat, and natural asphalt industries is given in the similar chapter of Volume II. Injury and employment data were collected from coal producers on the mandatory basis required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Producers of all other minerals (fuel and nonfuel) voluntarily reported the requested injury and employment data. The figures for 1963 are preliminary except for anthracite, coke, petroleum and natural gas, native asphalt, and slag which are final. Data for earlier years are final. The figures represent full coverage for all industries except the oil and gas industries for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1964

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

5. General Escapeway Requirements 5.1 Escape Routes Present escapeway regulations state "Every mine shall have two separate properly maintained escapeways to the surface which are so positioned that damage to one shall not lessen the effectiveness of the other, or a method of refuge shall be provided when only one opening to the surface is possible." "Escape routes shall be a. Inspected at regular intervals and maintained in safe, travellable condition, b. Marked with conspicuous and easily read direction signs that clearly indicate the ways of escape." "Application. "Regular" intervals means at intervals no greater than monthly where conditions are stable and oftener where conditions may change." "Designated escapeways inclined more than 30* from the horizontal shall be equipped with stairways, ladders, cleated walkways, or emergency hoisting facilities." As can be noted in present and proposed regulations there must be two separate properly maintained escapeways. In most operations, the escapeways will consist of one route that is the normal travelway used in day to day operations. The second route is usually a return airway through old work areas. Based on this generally accepted practice, we will designate the two types as primary and secondary.

Jan 1, 1976

By George Bockosh

Mr. Bockosh is an electrical engineer with the U.S. Bureau of Mines In Pittsburgh, and has devoted the last two years to research on underground illumination. He formerly was a mine maintenance foreman and worked two years underground. He is a graduate of the University of Pittsburgh, where he is now working toward his masters degree in mining. When Congress first legislated light in American coal mines, it was a little like mandating a walk on the moon before the first satellite had been put in orbit. It was never a question, of course, of whether it could be done. But no one knew quite how. It's one thing to string a few light bulbs, and quite something else to provide uniform, sufficient, safe and reliable illumination, with fixtures that will hold up under some of the toughest conditions in the world - in the life-and-death circumstances of a craggy, black cavern filled with dangerous, moving machinery. In fact, in 1969 when Congress originally mandated illumination standards for the work places of underground coal mines, no one even knew just how much light was needed. That question was answered within a year by the National Bureau of Standards. In a study commissioned by the U.S. Bureau of Mines, the Bureau of Standards determined that underground mine should be illuminated with a light intensity of 0.06 foot-lamberts, a measurement of light reflected from surfaces in the lighted area-as opposed to foot-candles, a measurement of light from the source of illumination-in order for miners to adequately see what they are doing. That study was followed by more detailed research done at the Bureau of Mines' direction by the Research and Development Department of the Naval Ammunition Depot in Crane, Ind. This work evaluated the specific lighting needs of miners engaged In more than 100 different job tasks in all three types of coal mining- conventional, continuous and longwall. The Naval Depot report brought forth nearly 300 pages of detailed lighting data and concluded that proper illumination of mine work areas would serve more than just the cause of mine safety.

Jan 1, 1976