Search Documents

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969

By ALBERT C. DURHAM

In anthracite mining , pumping is a problem of major importance , and water must be handled and rehandled in almost every mine whether the mine is in operation or idle . The motor - driven centrifugal pump is the most commonly used type of unit for the large pumping installations, and experience has . proved that fully automatic control has certain advantages over manual control . Some of these advantages are greater safety for maintenance personnel , continuous protection against faulty operation , which could cause damage to the Lumping apparatus , and lower pump -room operating costs .

Aug 1, 1948

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

By William G. Gruzenaky

The separation of yttrium and the individual rare-earth elements (lanthanons) from mixtures in which they occur has been a difficult problem through-out the years. Because of the increased interest in the various uses of these metals, the economy of their production may become of great importance. Studies relative to this problem, undertaken at the Federal Bureau of Mines Albany Metallurgy Research Center, resulted in the development of a solvent extraction method by which yttrium can be separated from the rare-earth metals. A separation factor of 10.93 was obtained between yttrium and cerium from a single-stage extraction, and a factor of 1.78 was obtained between yttrium and erbium from a multistage system. The valuable metals were extracted from euxenite by caustic soda fusion or by chlorination, and several separation methods were investigated. Partial separation of the yttrium and rare-earth element fraction was made by chemical methods and by solvent extraction. Thermal decomposition of aqueous rare-earth nitrates or selective ignition of yttrium and rare-earth oxalates yielded a fraction enriched in cerium. A fraction enriched in the light rare-earth elements resulted from a double sulfate precipitation, whereas a potassium ferrocyanide pr cipitation yielded a fraction enriched in yttrium. Precipitation with dimethyl phosphate yielded a fraction enriched in yttrium and heavy rare-earth elements. Enriched fractions were obtained with several solvent extraction systems. A system consisting of rare-earth nitrates, nitric acid, and tri-n-butylamine-3 methyl-2-butanone favored the separation of yttrium from the heavy as well as from the light rare-earth elements.

Jan 1, 1961

By L. M. Demers, D. C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology that results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoidsJ have been implicated as important biochemical mediator5 of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dust could influence the production of proinflammatory mediators in the lung environment. Primary cultures of rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500 and 1100°C. Prostaglandin E1 (PGE;V, thromboxane Ai (T}(Ay, and leukotriene 84 (LTB; levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 production was markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE1 production. Exposure of AM to freshly fractured coal dust resulted in a significant increase in production by AM, while exposure to stale coal dust did not influence AM TXA1 production. Neither "fresh" nor "stale" coal dust had any effect on LTB4 production. In vitro exposure of AM to untreated silica resulted in a significant increase in TXA1 PGE.,, TXA; and LTB4 production compared with control. However, exposure of AM to silica calcined to 11oo•c resulted in eicosanoid levels that were not significantly different from control. These effects were still apparent 8 wk after calcination of the silica particles. Silica was a more potent activator of AM eicosanoid production than was coal, and amorphous fumed silica was a more potent activator of AM eicosanoid production than was crystalline silica. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production and therefore may be important in the pathophysiological consequences of occupational mineral dust inhalation.

Mar 1, 1992

Create two air splits along the longwall face to isolate the shearer-generated dust to the immediate face area, maintaining a cleaner split of air in the workers' walkway.

Jan 1, 1994

By W. E. Wallace, S. -G. Xing, M. J. Keane, J. C. Harrison

"SummaryDiesel-exhaust particles from two sources were dispersed in aqueous mixtures of dipalmitoyl phosphatidyl choline, a major component of pulmonary surfactant, and were tested for genotoxicity. Diesel samples from the same sources were extracted with dichloromethane and transferred into dimethyl sulfoxide and subjected to the same assays. Both types of extractions yielded similar results in both the Salmonella mutagenicity assay and the sister-chromatid exchange assay using V79 cells. After separation of the samples into supernatant and sediment fractions, the activity of both diesel samples was shown to reside exclusively in the supernatant fraction for the solvent-extracted samples, and exclusively in the sedimented fraction for surfactant dispersed samples. These findings indicate that genotoxic activity associated with diesel particles inhaled into the lung may be made bioavailable by virtue of the solubilization / dispersion properties of pulmonary surfactant components.While diesel engine emissions are associated primarily with transportation, they are also very common in the workplace. Estimates for the U.S. are that as many as 1.35 million workers in as many as 80 000 workplaces are exposed to the combustion products of diesel engines (NIOSH, 1988). These occupations include, but are not limited to mining, agriculture, motor vehicle maintenance, fork lift truck driving, truck driving, and tunnel and bridge operation."

Mar 1, 1992

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

By F. E. Wormser

"Arsenic has been recently quoted at 10 1/2 - 11 cents per pound, an increase over the prevailing price of last fall, when arsenic was cents, as against pre-war prices around 4 cents is evidently a sustained demand for this material. The following statements are intended to summarize briefly some particulars regarding arsenic.Commercial arsenic is the white arsenious oxide (As203). This is the form in which it is generally marketed, as the uses of arsenic demand its industrial application in this form. Arsenic as an element finds rather restricted use in the hardening of lead shot, ere it is to some extent replacing the use of antimony, while white arsenic is employed in a variety of manufacturing processes, chief of which is the manufacture of insecticides and sprays. The poisonous nature of most arsenic compounds, the commonly known ones being paris green and lead arsenate, and its relative cheapness, make arsenic a material suitable for this purpose. The stimulation of agriculture during the war greatly increased the demand for arsenical insecticide. Glass making consumes a large amount of arsenic as it has been impart increased brilliancy to the glass. Crude commercial arsenic is often used to kill weeds along railroad tracks. Arsenious oxide is used also for preserving hides, while the disulphide, AS2S2), finds an application in dehairing hides for the finest grade leather, as it least affects the product. Orpiment (As233), is used in textile dyeing. Wall paints and wall paper formerly consumed considerable arsenic in the form of paris green, but this use has been largely,given up due to the poisonous nature of the dust from the product. Sodium arsenate for a similar reason, is now little used in printing where it had found application. The great objection to arsenical yes and paints is the risk of poisoning from use of the manufactured article. Sodium arsenite is the principal poisonous in¬gredient of many cattle and sheep dips. Arsenic compounds are also used medicinally."

Jan 1, 1920

Develop a new method for coal mint pillar stability evaluation and design based on pillar load measurements. Approach A novel approach to chain pillar stability evaluation and design for longwall coal mining panels has been developed by the Bureau of Mines. The evaluation approach uses an INTEGRITY FACTOR as the criterion for stability. Hydraulic borehole pressure cells developed by the Bureau are used to measure stresses in a pillar for stability evaluation. The results are used to improve the pillar design.

Jan 1, 1989

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTLATION NETWORK ANALYSIS

Jan 1, 1977

By Harry Dobroski, Larry G. Stolarczyk

A medium-frequency (MF) communication system has been built and has been tested in underground mines. It provides radio coverage to vehicles and personnel anywhere in the mine via parasitic coupling into existing mine conductors. The system consists of base stations, repeaters, and vehicular and personnel transceivers. Air-core antennas for vehicles and clamp-on antennas for base stations and repeaters were designed for maximum coupling efficiency using existing mine wiring. Personnel transceivers are of a unique vest design that features a low physical profile, good user comfort, and efficient antenna design. In-mine tests show impressive results. Range between rubber-tired vehicles and base stations is often measured in miles. With repeaters, greater range is possible.

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots."

Dec 1, 1942

To improve a miner's chance of survival during an emergency by providing immediately avail-able breathable air and protection from toxic gases until a longer-duration breathing apparatus, stored nearby, can be reached. Approach: A belt-carried apparatus which can provide a closed-circuit atmosphere for ten minutes breathing has been developed under a Bureau of Mines contract. How It Works: Water vapor and carbon dioxide in the user's exhaled breath are removed, and oxygen is supplied, by chemical reactions. When the user exhales into the mouthpiece, water vapor in his breath reacts with potassium superoxide (KO2) stored In the canister to produce oxygen. The other product of this reaction (KOH) reacts with carbon dioxide and removes it from the air. The oxygen-enriched air then flows from the canister into two breathing bags. When user inhales through the mouth, that air is drawn out of the bags, makes a second pass through the chemical-containing canister, and flows into the mouthpiece tube. A nose clip is worn to seal off the nasal passages.

Jan 1, 1975

Improve the safety and comfort of operators of large mining equipment. Approach Develop an improved driver restraint system that is easy to use, reliable, and cost-effective, while providing increased protection in the event of a collision or rollover. The Novel Restraint System There are several problems associated with conventional lap-belt type restraint systems. Among these are: restriction of movement, lack of comfort, and fear of entrapment. Standard seatbelts become dirty and oily from lying on the vehicle cab floor and can ruin a driver's clothes. Some haulage equipment may not even have seatbelts available to drivers since they are sometimes removed during maintenance activities or as a result of vandalism. Recognizing a need to address such problems by providing a more acceptable means of driver restraint, the Bureau of Mines designed and fabricated a novel vest-type restraint system. The vest is designed to be worn during a driver's 8-hour shift and would be issued much like safety glasses, hard hats and safety shoes, thus becoming part of the operator's individual protective equipment and assuring that each vehicle has a restraint system when in operation. The vest-

Jan 1, 1985