Search Documents

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984

By David L. Moffatt

Considerable current interest is evident[l,2] in the use of transient electromagnetic methods for subsurface remote sensing. A transient method is discussed which uses a periodic video-type pulse containing a wide frequency range. A video pulse is used as an interrogating signal both for "target" identification and detection for relatively short depth (c 20 meters) applications in soil and soft rock media. If the medium is favorable, e.g., hard rock, greater depth applications appear to be feasible. The same procedures would be applicable for deep geological exploration but would require a substantial reduction in frequency and increase in target size. It should be noted that video pulse generators with 35 kv peak voltage and nanoseconds base widths are now within the state-of-the-art, thus significant power over broad spectral ranges is possible. In the design of a video pulse sounding system, 5 main problem areas can be identified; 1 ) selection of the pulse shape or spectral content of the video pulse, 2) design of a radiating structure which effectively couples such a pulse into the medium, 3) isolation of the radiating and receiving mechanisms, 4) realistically accounting for the dispersion and attentuation of the medium and the air-medium interface, and 5) interpretation or processing of the received signal waveform. Each of these problem areas will be discussed and illustrated with experimental and/or theoretical results. The Video Pulse Selection of the proper video pulse signal is dictated by 3 considerations, the maximum desired depth of penetration, the attenuation of the medium and the required resolution and size of the target. For a lossy medium, penetration and resolution are clearly at cross purposes and a compromise is necessary. The exact nature of the compromise is dictated by the application, but the spectrum of the video pulse should not contain any frequencies higher than the predicted cut-off, i.e., that frequency which is attenuated to the threshold level of the receiver. As a practical matter, it may be necessary to select 1 or 2 video pulses reasonably suited

Jan 1, 1973

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

By S. H. Ash

As part of the work done at the Washington coal mines during the year 1929 , a study was made of the safety practices in and about the mines . Inasmuch as electrical blasting has made considerable headway it is interesting to note the manner in which it is done and the reasons why it was discarded at some of the mines . Blasting is done at the mines in the State by means of capped fuse , electric blasting " caps , " and in some instances by electric delay detonators . Black blasting powder with fuse is used at most of the open- light mines . The use of squibs was discontinued several years ago because the coal operators , without exception , recognized the dangers incidental to their use . Permissible explosive and dynamite are also used at some of the open- light mines . With the exception of some rock work and the driving of level work in gangways and air courses the explosive is detonated by means of capped fuse .

Apr 1, 1930

By James Westfield

Uranium activity has introduced a comparatively new hazard to United States mining. In addition to the hazards common to all mines, uranium mines have a complex health problem of radiation damage. Like many new processes, radiation and nuclear energy can be made to serve man in many useful ways when properly understood and handled; but, like fire, gases, and electricity, their potential dangers must be known and respected, and appropriate precautions must be taken or death may result. Since 1950 the Public Health Service has been conducting basic investigations on exposure to radon and its daughter products and the effect of exposure upon the health of miners in uranium mines of the Western States. The Bureau of Mines assisted in several of these investigations, especially in mines on Indian lands. The studies have shown that a serious health hazard exists from radioactive exposure that might cause lung cancer if continued over a number of years. The Public Health Service report, Control of Radon and Daughters in Uranium Mines and Calculations on Biologic Effects,6/ shows that 55 percent of the uranium mines employing 64 percent of the miners had atmospheric concentrations more than five times the working level now accepted as reasonably safe for industrial exposures. Extensive control measures are necessary to reduce these concentrations to the suggested working level of less than 300 micromicrocuries of total radon daughter products per liter of air.

Jan 1, 1958

By Robert J. Hundhausen

This information circular is one of a series of Bureau of Mines reports dealing with mining and milling methods and costs . It describes the operations at the Little Pittsburg mine in the Pine Creek area of the Coeur d'Alene mining region near Kellogg , Idaho . The mine and mill have been operated successfully from 1942 to the present .

Feb 1, 1948

By F. R. Lee

This publication lists permissible equipment approved by the Bureau of Mines during 1965 and 1966 (calendar years), except for breathing apparatus and explosives. The purpose of this publication is to inform the public about approved equipment for safe use in underground mines.

Jan 1, 1968

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. M. Suryan, V. Vallyathan

"Freshly ground and aged anthracite and bituminous coal samples were investigated by electron spin resonance (ESR) spectroscopy to detect the presence, concentration and reactivity of free radicals. Freshly ground anthracite coal produced greater concentration of free radicals than the bituminous coal, and the radical reactivity was also greater for the anthracite. The reactivity of the newly produced free radicals in the anthracite dust correlated with the dust's toxicity. Furthermore similar coal-based free radicals were detected in the lung tissue of autopsied coal miners, suggestive of persistent reactivity by the embedded coal dust leading to the progressive disease process. Results of the studies on the severity of coal workers' pneumoconiosis (CWP) and free radical concentration m lung tissue support this hypothesis.INTRODUCTIONCOAL WORKERS' PNEUMOCONIOSIS (CWP) has been an important topic of concern to miners, mining engineers, epidemiologists and medical researchers for decades. It is well known that the prevalence and severity of CWP differ markedly between different regions and mines despite comparable exposures to respirable dust (REISNER and RoBOCK, 1977; HURLEY et al., 1979). These variations in pathogenicity of coal mine dusts can only partially be explained by differences in the mineral composition and by rank of coal (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). Cytotoxity studies on mammalian cells do not correspond well with the human disease pattern (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al.,1980; VALL YA THAN et al., 1988). For example, while epidemiological studies of coal miners (REISNER and ROBECK, 1977; HURLEY et al., 1979) indicate that the prevalence of CWP correlates roughly with the rank of coal, such correlation has not yet been established in biological studies, despite considerable effort (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). In order to help resolve this apparent paradox we have undertaken a systematic study to evaluate whether any correlation exists between the concentration of free radicals present in fresh or aged coal dusts from two well-characterized U.S. coals. This study was also prompted in part by observations reported in the literature that organic free radicals can be formed on the surface of freshly fractured coals (LEBEDEV et al., 1978; DULIBA and CLARKSON, 1984). In particular, ARTEMOV and REZNIK (1980) noted that the decay lifetimes and, hence, the reactivity of the organic free radicals formed on crushing Russian coals, .depended"

Jan 1, 1989

By Marvin E. Lane

This paper , which describes the mining methods and practices at the Hayden Creek lead mine of St. Joseph Lead Co. in southeast Missouri , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The Hayden Creek mine is in the W 1/2 sec . 7 , T. 36 N. , R. 4 E. , St. Francois County , Mo. , about 1 mile southwest of the town of Frankclay ( fig . 1) . The mine is on the west edge of the mining district known as the Lead Belt . However , neither the ore body nor the underground workings are connected with those of any other mine in the district . In contrast with most operations in the district , underground haulage is entirely trackless , and nearly complete delineation of the large , well -defined ore body by drilling permitted comprehensive planning of development and mining in advance of shaft sinking . The ore differs in character and occurrence from that of the main ore deposits in the Lead Belt in that the lead mineral , galena , occurs in the dolomitic matrix enclosing granite boulders instead of in dolomite limestone .

Apr 1, 1957

By James S. Browning

For the past several years, the Bureau of Mines has conducted laboratory and continuous process development work on weathered mica pegmatites and micaceous schist ores to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotadon of mica: an acid cationic method for recovery of coarse mica, and an alkaline anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatites and micaceous schists. Concentrates containing over 98 percent mica, with recoveries ranging from 77 to 92 percent, were obtained from the pegmatite ores. The micaceous schist ores yielded concentrates containing 95 to 98 percent mica, with recoveries ranging from 70 to 83 percent. Part 1 of this report summarizes the process development work and demonstrates the feasibility of producing commercial- grade mica concentrates. The report also includes details of commercial beneficiation and grinding of .mica.

Jan 1, 1973

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965

By K. K. Kelley, W. W. Weller

This report contains experimentally determined heat capacity data for four crystalline sulfides -- AsS , GeS , NiS , and Ni3 S₂ -- over the temperature range from 50 ° to 298.15 ° K. The heat capacity data were used to evaluate the entropies of the sulfides at 298.15 ° K. Entropies of formation from the metals and rhombic sulfur and from the metals and diatomic sulfur gas are also included .

Jan 1, 1964

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By C. A. Komar

The Bureau of Mines conducted experiments on one synthetic and three natural sandstone samples to investigate the effects of acoustic energy on the flow of brine in porous media. Ultrasonic energy at a frequency of 20 kc per second and an intensity of 55 watts per cm2 was irradiated in the direction of the fluid flow and in the opposite direction for distances of 1/2 and 2 inches between the vibrating device and the sample face and under conditions of suppressed and nonsuppressed cavitation. Forty tests were conducted: 32 with a pressure differential of 0.64 psi across the samples, 2 with 5 psi, and 6 with 15 psi. Acoustic waves altered the rate of flow of the brine through the samples, but this effect was observed only at low differential pressures and from a practical point of view was insignificant. As a result of irradiation, however, the samples exhibited reduced permeability. This reduction was probably caused by the shifting of solid particles dislodged by the acoustic waves.

Jan 1, 1967

By D. Harrington

The mining industry of the United States has for many years possessed the dubious aistinction of having the poorest accident rate of all of the major lines of industrial endeavor in this country, and until recently there ras little or nothing to show that any material improvement might be expected. However, there are now numerous trends indicating that the corner has ceen turned at last, and it is strongly hoped that the mining industry is likely to follow the railroads, the cement and other industries in operating with occurrence of only a reasonable amount of loss of life and limb through accidents. The complete accident figures for metal and nonmetallic mineral mining for 1931 are not yet available, but fragmentary data shor that 1831 vill un- questionably have very low accident rates, probably the lowest in the history of our metal mines. One underground metal mine has produced over 14,000,000 tons of copper ore rithout a fatality; another metal mining company with an electric slovel operation has handled upwards of 75,000,000 tons of material, copper ore and waste, without the occurrence of a fatality; an iron-ore compan, which orns six mines (three underground, three open pit), has operated every one for a year or more without a lost-time accident with a con- siderable number of employees and a large production; and alot.er iron-ore producer with 30 mines and about 3,000 employees as an average of nearly 10 months of operation in 1931 without a lost-time accident. umerous other wonderful safety records of metal mines in 1931 indicate unmistaimbly tat the record of the noncoal mining industry of the United States as a role in 1931 will undoubtedly be found to be excellent. According to the latest relatively complete figures (those of 1930) available for the coal industry, fewer than 650,000 persons are employed in and around the coal mines of the United States, the figures indicating at a little over 493,000 people are engaged in bituminous mining and a little under 151,CCO in anthracite mining. Bureau of Mines complete figures suc that 2,053 persons were killed and 103,821 non-fatally injured in our coal

Dec 1, 1932

By C. P. Mabie

This report summarizes studies by the Bureau of Mines in developing a simple method for estimating the phosphorus pentoxide (P205) content of finely ground sedimentary phosphate ores and beneficiated products. The method used involved leaching, filtration, and precipitation. The Bureau found that measurement of the volume of ammonium phosphomolybdate precipitate obtained from samples containing 16.8 to 37.7 percent P205 and the use of an appropriate calibration curve permitted estimates of percentage of P205 content accurate within ± 1.1 to ± 2.6 percent, respectively, at the 95-percent confidence limits. Incidental to mineral dressing and petrographic investigations of western phosphate ores in 1959, the Bureau of Mines undertook development of a simple process-control method for rapid on-the-spot evaluation of phosphate-mineral recovery. Because of the fine-grained and obscure character of western phosphate ores, chemical, rather than microscopic or petrographic, techniques were investigated. The described method involves acid decomposition of the ore or product, filtration, addition of ammonium molybdate reagent to the filtrate, and centrifuging and measuring the volume of yellow ammonium phosphomolybdate precipitate produced.

Jan 1, 1961

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By David M. Hyman

Outbursts are sudden and violent releases of gas and coal that result from a complex function of geology, stress regime, and gas pressure and content. The Bureau of Mines has reviewed methods for prediction and mitigation of such outbursts in use worldwide, as an aid in selecting the proper techniques for use in specific mine environments. Outburst-prone coal may be distinguished from normal coal by its sorption-desorption velocity. Three types of methods used to characterize the kinetics of sorption-desorption are described; all are based on the ability of outburst-prone coal to release, through desorption, methane or carbon dioxide much more rapidly than normal coals. Other prediction methods, based on borehole samples, are also described. Various mitigation methods described and evaluated include (1) working the least stressed, less disturbed, lowest gas content seam in multiple-seam areas; (2) mine opening geometry; (3) inducer shot firing; (4) water infusion; (5) localized stress relief, using boreholes or by cutting a reliever slot in the longwall face; and (6) other gas drainage methods.

Jan 1, 1987

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991