Search Documents

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master's degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By Geo S. Rice

"Three men lost their lives in the Black Diamond Coal Mine near Seattle, Wash., recently while wearing oxygen breathing apparatus. The press dispatches stated that these men lost their lives while practicing with the apparatus. Later reports stated that the men died while attempting to make a trip 1200 feet down a 25 degree slope which was filled with black damp, in order to measure the amount of water that had accumulated at the bottom of the mine, and the trip was attempted with oxygen in the tanks of the apparatus with dials indicating only 45 minutes supply. The oxygen in the tank was used up and the men therefore lost their lives from a deficiency of air to breathe.In spite of all the education and training done by the Government to prevent accidents, men are prone occasionally to take unnecessary chances. Every piece of apparatus, no matter how perfect, has its limitations. The Government, through the agency of the Bureau of Mines, has trained many thousands of miners in the use of mine rescue apparatus. The training has been given to all miners who requested it, and the Bureau has gone to the extreme of urging miners to join the rescue and first-aid classes. In spite of all the efforts of the Government, men occasionally attempt the impossible."

Jul 1, 1920

By Robert G. Lundquist

This report summarizes all relevant findings and conclusions regarding capabillty of high-energy projectile impact to operate effectively in an open pit mining environment and to successfully handle secondary breakage and bench scaling problems. A silenced, aimable, mobile projectile launcher was designed and fabricated, utilizing a Government-furnished smooth-bore, 90 mm cannon. The silenced launcher was tested at the contractor's test site prior to shipment to ANAMAX Mining Company's Twin Buttes Mine near Tucson, Arizona. Demonstration tests were conducted at an inactive waste dump in the mine on 39 oversize boulders to determine the relationship between boulder size and projectile energy required for secondary breakage. The high energy projectile impact method (known by the acronym REAM -Rapid Excavation and Mining) was tested on an additional 23 boulders in the working mine and on 31 areas of potentially loose rock high on the pit walls. Most of the secondary breakage tests were successful and acceptable for open-pit mining purposes without producing large amounts of fly rock. Five of the 31 scaling tests were successful with one shot, but most of the remainder required two or more shots, and a few could not be dislodged because they were not as loose as they appeared to be, based on visual examination from a distance. Cost comparisons between the REAM method and conventional methods of secondary breakage and bench scaling are discussed. A film documentary, REAM--Mining Applications of High Energy Projectile Impact, has been produced by the contractor depicting the applications of the silenced cannon.

Jan 1, 1976

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESR) and cytotoxicity measurements were made on newly fractured silica to examine specifically the role of the fractured-induced, siliconbased radicals (Si· and SiO·), and silica-generated hydroxyl (·OH) radicals in the mechanism of the cell membrane damage by silica. The concentration of the Si· and SiO· radicals was controlled through decay processes, thermal annealing, and boiling, while that of the ·OH radicals was varied by using catalase, superoxide dismutase, KMnO4, Ha2seO3, ascorbic acid, and metal ions, and monitored via ESR spectroscopy. The dust's cytotozicity potential was evaluated by measuring the silica-induced hemolysis and also by determining lipid peroxidation (using linoleic acid). Prom the comparison of hemolysis and ESR results it is deduced that the radicals play little· or no role in the silica-induced hemolysis. However, the lipid peroxidation data indicate that the radicals might be involved in the initiation of an oxidative chain reaction leading to the macrophage membrane damage through lipid peroxidation. INTRODUCTIONThe biochemical mechanism of Quartz-related pneumoconiosis is still not fully understood. It is believed, nevertheless, that one event of primary importance is the perturbation of cell membranes by the dust particles (Allison et al., 1966; Allison and Harrow, 1971; Bateman et al., 1982; Parazzi, et al., 1968; Reiser and Last, 1979; Shi et al., 1989; Summerton et al., 1977). The ensuing cell-membrane damage unleashes certain lytic enzymes resulting in additional cell injury and eventual fibrosis (Nolan et al., 1981; Summerton et al., 1977). Thus considerable effort is currently being made towards the understanding of the processes by which quartz particles disrupt the membrane of a red blood cell (RBC) or a pulmonary alveolar macrophage (PAM). A simple but important method of evaluating the membrane damage potential of a dust is the hemolysis test (Harington et al., 1971). Even though this test is used routinely for screening dusts for their cytotoxicity potential, the biochemical mechanism underlying the cell lysis by many dusts, including quartz, is still controversial (Kilroe-Smith, 1974; Singh and Rahman, 1987), and this provided us the impetus for the present undertaking."

Jan 1, 1989

By Wilbur I. Duvall, Thomas C. Atchison, Joseph M. Pugliese

Short cylindrical charges were detonated in drill holes in rock to determine the effect that decoupling ( defined as the ratio of the radius of the hole to the radius of the charge ) has on the strain - generating abilities of explosions in rock . The amplitude and period of the strain pulses produced in the rock were studied as a function of distance , size of charge , and decoupling . The main results of these studies were that , for a given distance and size of charge , the amplitude of the strain pulse decreases as decoupling increases and the period of the strain pulse decreases at first and then increases as decoupling increases . A simplified theory of decoupling is presented that satisfactorily explains the experimental results . The information presented makes it possible to predict the effect of decoupling on explosiongenerated strain pulses in rock and thus helps the explosives user evaluate the effect of decoupling on his blasting .

Jan 1, 1964

By E. R. Rodriguez

Improved practice resulting from recent changes in the method of supplying compressed air and in pneumatic drilling equipment used in secondary drilling and in development work at the Morenci mine of the Phelps Dodge Corp., has resulted in improved safety conditions, as well as in a reduced cost per foot of drilling. A large stationary compressor installed outside the mining area and the compressed-air pipelines in the mine were replaced by portable compressor units. A self-propelled, self-contained drilling unit was obtained for drilling large footages where short moves were involved. Large wagon-drill units were replaced by faster and lighter drill machines and conventional bits by carbide insert bits. The safe practices employed in air drilling and in the related blasting and scaling operations have contributed to an excellent safety record at this mine. The complete sets of instructions listed in the company codes of safe practice aid materially in training employees.

Jan 1, 1956

By R. Y. Williams

In this report an attempt is made to discuss the first cost of each of several types of mine-ventilation stoppings, as well as the total annual expense of maintaining a stopping during its required period of service. Such data furnish a basis for comparison of the efficiency of the different types, and are of great importance to an engineer planning the development of a mine. The data given were obtained through an investigation conducted under a cooperative agreement between the Bureau of Mines, the Illinois State Geological Survey, and the department of mining engineering of the University of Illinois. The report itself is published by the Bureau of Mines as a contribution to the literature on safety and efficiency in coal mining.

Jan 1, 1915

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

The Bureau of Mines equipped a longwall shearer with a water-jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 190 psi, and with water-jet-assisted cutting pressures ranging from 1,000 to 6,000 psi. At water pressures of 3,000 psi and higher, dust concentrations were reduced by as much as 85 pct via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1986

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By James S. Browning

Heavy liquids have been used to separate minerals of different specific gravities for many years.4 5 6 7 8 9/ The method permits substantially quantitative evaluation of a variety of minerals and requires much less time than the usual methods of chemical analysis. This Bureau of Mines investigation was conducted to determine the applicability of heavy liquid mineral separation to the evaluation of certain spodumene and kyanite ores, prepared mixtures, and plant products. After careful standardization of the particular mineral and associated gangue, estimates of chemical analyses could be obtained from results of heavy liquid separations.

Jan 1, 1960

By Oliver C. Fursman

This work was conducted to determine the feasibility of producing aluminum-silicon alloys in a pit-type, three-phase electric-arc furnace. Two carbon-lined furnaces were used in the tests. The power input ranged from 120 to 240 kw. in the small furnace and from 420 to 460 kw. in the large furnace. Energy consumption ranged from 5.3 to 11.5 kw.-hr. per pound of alloy produced and electrode consumption, from 240 to 510 pounds per ton of alloy produced. A wide range of crude aluminum-silicon alloys was produced by direct smelting of clays or similar aluminum silicate raw materials, using hogged fuel or wood chips as the major source of carbon in the furnace charge, and silicon of high grade was produced by smelting quartz. The aluminum content of the aluminum-silicon alloys ranged from 15 to 55 percent. Alloys produced from a white opaline-silicate clay were relatively free of iron, titanium, and other impurities. Those produced from western fire clays and kyanite, although richer in aluminum, contained considerable amounts of impurities. The purity of the alloys depended largely on the composition of the raw materials.

Jan 1, 1960

1. In 2001, a total of 785 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Examples of nonmetal mining operations include the mining of clay, trona, barite, phosphate rock, gypsum, talc, gemstones, and pumice. Nonmetal mines comprised 5.4% of all mining operations.1 • Nonmetal mining operations are located in all but seven states or territories (Alaska, Delaware, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands). • The median number of operator employees per nonmetal mine was 6.1.2 • Mines producing common clay comprised 31.2% (n = 245) of all nonmetal mining operations.

Jul 1, 2003

By E. P. Youngman

At the time of the preparation of the monograph upon the mining legisla- tion of Newfoundland, by the Imperial Institute of London, the existing local statutory law (as distinct from case laws and the applicable English acts) con- sisted of the following legislation: 1. Chapter 129 of the consolidated statutes, entitled "Of Crown Lands, Timber, Mines and Minerals," as amended by the Crown lands act, 1928. 2. Chapters 131 and 132 of the consolidated statutes (acts relating to mines regulation and rewards for discovery of minerals, respectively). 3. Crown lands act, 1918, as amended by the crown lands (amendment) act, 1921. 4. The Labrador Act, 1927. 5. The Crown royalties act, 1927. 6. Crown lands act, 1928, together with rules and regulations issued thereunder.

Oct 1, 1932

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By O. C. Ralston

The Bureau of Mines has under development on a technical scale an electrolytic process for treating oxidized ores of zinc , using caustic soda as an electrolyte . Whereas the Bureau process can alternately make either solid zinc or zinc dust , the following paper , from the Ludwigshafen research laboratory of the well -known I. G. Farbenindustrie , A. G. , of Germany, deals only with production of zinc dust from sodium zincate solutions and may well serve as introduction to the subject for American metallurgists . The Bureau of Mines pioneered in the idea ; a study on laboratory scale by H. J. Morgan and 0. C. Ralston was made early in the First World War, and published in Transactions of the American Electrochemical Society . The Eckardt paper , translation of which follows , goes more thoroughly into the preparation of electrolytic zinc dust , and later publications of the Bureau of Mines will deal with broader details and application of the idea to treatment of lowgrade ores and metallurgical intermediates , which is the point where Eckardt left off . 4 The Eckardt report became available through operations of Field Information Agency , Technical ( FIAT ) of the Office of Military Government for Germany (US ) , which made bibliofilm copies of the files of internal technical reports of many of the German industrial establishments , Eckardt's report is dated April 1939 and was taken on FIAT Microfilm Reel MM 106 , frames 82-101 , which is on file as Publication Board Document 41411 in Office of Technical Services of the U. S. Department of Commerce , Washington , D, C , Eckardt points out that the normal source of zinc dust is the blue powder of the zinc retorts , which decreases in volume every year owing to technologic improvements in zinc smelting. I. G. saw the importance of making a

May 1, 1948

By D. C. Crowell, A. G. Loomis

Both Dimensional and Inspectional Analysis are developed from fundamental concepts , and dimensionless groups are derived which represent the viscous , capillary , and gravitational forces existing in two - phase , incompressible flow in petroleum reservoirs . It is shown how properly scaled models may be devised by means of the foregoing groups . Laboratory measurements with such models faithfully duplicate the behavior of the reservoir on a miniature dimensional and compressed time scale , and when all the pertinent variables are evaluated , the model is a most effective tool for the study of complex fluid displacements in the reservoir . Applying the Principle of Similitude , it is shown how dimensionally scaled models are applied to various types of reservoir displacements : ( 1 ) Oil displaced by water , ( 2 ) gas displaced by water , and ( 3 ) miscible displacement . The special case of water displacing gas by imbibition is analyzed , and it is shown that the dimensionally scaled model must be fabricated of sandstone rather than unconsolidated sand , which is generally used in such models . This report is intended to be a review and summary of the application of Dimensional Analysis to reservoir displacement problems for those who are beginning the study of this useful and interesting method .

Jan 1, 1964

By J. B. Zadra, H. J. Heinen

Electrowinning molybdenum from oxide feed materials dissolved in a variety of molten baths was investigated . A NaCl - NaF - Na₂ B₁ O -Mo0, system operating at 1,000 ° C in a cell without a protective atmosphere gave the best current efficiency , metal - to - cathode adherence , and purity of electrowon Technical - grade molybdic oxide , containing associated impurities of aluminum , iron , copper , silicon , and tungsten in combined quantities of 10 percent , was used as feed material to produce dendritic crystals of molybdenum metal containing less than 0.5 percent total base metal , carbon , and oxygen impurities . Arc - melting molybdenum electrowon from either chemically pure or commercial - grade Mo0, produced ingots that contained less than 0.1 percent total impurities and had hardness readings of 168 to 200 Vhn .

Jan 1, 1964