Search Documents

By T. A. Sullivan

The use of sulfur combined with either sand or waste copper tailings was investigated by the Bureau of Mines as a substitute for a good graded aggregate in asphalt paving materials. The research was part of a utilization program to develop meaningful uses for a projected oversupply of sulfur. Many sections of the country lack good aggregate for paving but do have available sources of sands and sulfur. The development of paving mixtures of desert sands or tailings with sulfur and asphalt was accomplished in the laboratory and tested by laying small paving test sections. Three types of material were studied for use with the sulfur and asphalt. They were (1) a concrete sand similar in gradation to river or beach sands, (2) desert blow sand, and (3) waste copper tailings. Desert blow sand and waste copper tailings are much finer than concrete sand. Mix designs were established for the three types of materials, sulfur, and asphalt used in the paving materials. The best mix designs were as follows, in weight-percent: 80.5 concrete sand, 13.5 sulfur, and 6 asphalt; and 77 either blow sand or tailings, 17 sulfur, and 6 asphalt. Small-scale testing showed that these mixtures were suitable paving materials but would require specialized equipment for transporting and laying. The chemical modification of sulfur to obtain properties that would allow placement of these materials with normal asphalt paving equipment was studied. Results indicate that reacting sulfur with dicyclopentadiene before adding it to the paving mixture was effective in modifying the sand-sulfur-asphalt paving so it could be placed and rolled with conventional equipment.

Jan 1, 1975

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By J. G. Donaldson

Binary alloys of molybdenum and tungsten were prepared by the Bureau of Mines in laboratory-scale experiments by hydrogen reduction of their vaporized hexafluorides. Near-optimum deposition parameters were determined, and the nature of the deposited alloys was investigated. Dense, homogeneous alloys were codeposited between 650° and 750° C with a reduction efficiency of more than 75 percent. The alloy composition was uniform when the hydrogen ratio in the gas feed mixture did not exceed 3 times the stoichiometric requirement. Regulating the proportions of the metal hexafluorides in the gas feed provided a large degree of control over the composition of the deposit. Hardness of the deposits varied directly with the proportion of excess hydro,,,, in the gas feed and with the weight-percent of tungsten in the alloy. Hardness was not affected by deposition temperature over the range 650° to 750° C for specimens of similar composition. Extreme brittleness and unsuitable physical shapes of the alloys prevented tensile strength measurements.

Jan 1, 1966

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional uranium ore-processing steps to confine and permit controlled disposal of radioactive wastes. Surveys of Ra226 contamination of liquid wastes from uranium mills indicated that the Vanadium Corporation of America plant at Durango, Colo., had one of the more urgent problems. A possible procedure for minimizing the waste disposal problem was to reuse the waste solution in the mill--in effect, erasing the need for disposal of liquid waste. In examining this possibility, interlocked bench-scale leaching and solvent extraction tests simulating the Durango flowsheet were made. The simulated reuse of barren raffinate for leaching and washing was carried through three separate campaigns of 9, 12, and 35 cycles each.

Jan 1, 1961

By R. O. Dannenberg

The Bureau of Mines investigations described in this report were undertaken to devise a process to economically recover precious metals and copper from low-grade, complex electronic scrap generated in large quantities by military and civilian electronic operations. Leaching with various media is applicable to certain selected items of electronic scrap but cannot be practically applied to complex mixtures of scrap. A process comprising incineration, caustic leaching to remove aluminum, smelting with a siliceous slag, and electrolysis recovered 99.9-percent-pure copper metal and anode slimes assaying more than 7,000 ounces per ton of combined precious metals. Silver, gold, and copper recoveries were 93, 95, and 87 percent, respectively. Cost analysis indicated that an alternative process using direct smelting of the scrap to make assayable products for sale to a custom smelter would provide better overall financial returns.

Jan 1, 1972

By J. W. Holcomb

Many mines are opened into the coal beds by shafts; and, at some of these operations, the same cages or skips that are used for hoisting coal also are used for transporting men into and out of the mines. At some mines, separate man-and-material shafts are maintained, and the cages in these are utilized for transporting men and supplies only. In most instances, these cages are operated either singly or in pairs by a hoisting engine installed in a building near the shaft. Single ropes from the tops of the cages pass over bull wheels on the head frame to either electrically or steam-driven hoisting engines that require engineers to operate them. There are records of several instances where hoisting engineers have become incapacitated suddenly while hoisting men, and the passengers on the cages were killed or injured. Where the same cages are used for hoisting cars of coal and for lowering and hoisting men, especially where self-dumping cages or skips are used, safety pre¬cautions must be taken, such as providing steel bonnets for the cage deck, enclosed sides, adequate handholds, gates for closing the end openings, safety catches, and locking devices to prevent accidental dumping. Some of the newer hoisting installations are of the elevator type; where an operator rides in the cage in the same manner as an elevator operator in a building. These cages have single or multiple decks and are primarily for transporting men; but, in some instances, supplies also are transported. They are a great improvement over the installations where the same cages are used for hoisting cars of coal and transporting men.

Jan 1, 1952

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By E. R. Bauer

The U.S. Bureau of Mines is investigating strata interactions associated with mining of multiple coal beds to provide the mining industry with improved methods of planning and developing multiple coalbeds, conserving resources, and increasing the safety of underground coal mining. This study involves analytical predictions and underground observations of longwall development ground control problems at a south-central Pennsylvania coal mine affected by subsidence induced by multiple-seam mining. As predicted, strata interactions were found in upper mine areas mined over lower mine gob. Observations revealed roof deterioration accompanied by excessive water inflows in the first 170 ft after crossing the gob line as mining entered and exited the subsided area (over the lower mine gob). In contrast, superimposed mine areas and areas mined a substantial distance out over the gob showed no signs of interaction with previous lower seam mining, again as predicted.

Jan 1, 2010

By T. E. Ackman

Scale inhibitors and slow-release polymers were tested by the Bureau of Mines at mine drainage treatment facilities. The scale inhibitors were investigated to determine their effectiveness in controlling gypsum (CaSO4) scale; the polymers were investigated to determine their effectiveness for increasing settling rates of suspended iron hydroxide. Two types of scale inhibitors were tested at a site having a severe CaSO4 scaling problem. Both proved to be effective in controlling scale formation; in addition, one caused the dissolution of CaSO4 deposits. Slow-release polymers were tested at three mine drainage treatment facilities. These gelatinous polymeric flocculants were found to be convenient and easy to use, but only effective when pH could be controlled.

Jan 1, 1984

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe&apos;s are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC&apos;s of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of aflame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety laps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

To increase awareness of float coal dust explosion hazards in the mining industry.

Jan 4, 2006

By X. C. Shi

Bacterial mutagenicity and mammalian cell chromosomal and DNA damage in vitro assays were performed on a diesel exhaust particulate material (DPM) standard in two preparations: as an organic solvent extract, and as an aqueous dispersion in a simulated pulmonary surfactant. U.S. National Institute for Standards and Technology DPM SRM 2975 expressed mutagenic activity in the Salmonella reversion assay, and for in vitro genotoxicity to mammalian cells as micronucleus induction and as DNA damage in both preparations: as an acetone extract of the DPM mixed into dimethylsulfoxide, and as a mixture of whole DPM in a dispersion of dipalmitoyl phosphatidyl choline. Dispersion in surfactant was used to model the conditioning of DPM depositing on the deep respiratory airways of the lung. DPM solid residue after acetone extraction was inactive when assayed as a surfactant dispersion in the micronucleus induction assay, as was surfactant dispersion of a respirable particulate carbon black. In general, a given mass of the DPM in surfactant dispersion expressed greater activity than the solvent extract of an equal mass of DPM.

Jan 1, 2009

By William D. Monaghan

The U.S. Bureau of Mines evaluated a teleoperated continuous mining machine for deep mining in thin-seam applications as low as 1 m. Teleoperation increases the safety of mining machine operators because it removes the operator from the face, an area of immediate hazards to safer outby locations. By using teleoperation, the miner can avoid many including unexpected roof falls that can maim or kill miners instantly, methane and coal dust explosions that can be ignited with just a small spark or flame, adverse health effects from miners breathing coal and silica dust, adverse long-term inner ear damage from loud noise pollution, and other hazards related to heavy mining equipment moving about in confined underground roadways. This report presents the surface evaluation results of a teleoperated control system.

Jan 1, 1994

By Michael R. Yenchek

The U.S. Bureau of Mines investigated the operational characteristics of spliced portable power cables. This research had a dual purpose: (1) to determine the thermal and mechanical performance of repaired trailing cables and compare them with undamaged cables and (2) to gauge the impact of long-term, localized heating on the insulating and jacketing materials contained in cable splice kits accepted or approved by the Mine Safety and Health Administration. The ranges of splice joint resistance and tensile breaking strength were determined from laboratory measurements. The choice of crimping tools affected the strength of the splice under tension. Thermal profiles of energized spliced cables were constructed, which showed that spliced conductor joints operated 5 to 20°C hotter than the intact cable at rated currents. Accelerated life tests of thermally aged samples of splice kit insulation and jacket materials confirmed a deficiency in the thermal rating of the insulating tape. The recommendations in this report may be utilized to revise splice kit design, splice kit approval criteria, and trailing cable loading guidelines. Characterizing the thermal operating limits of spliced trailing cables may help to minimize the associated risks from explosions, fires, personnel burns, and shock.

Jan 1, 2010

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By R. T. DeWoody, J. W. Chester, W. C. Miller

The work was done to develop a relatively efficient muffler for quieting the exhaust of a rock drill . The exhaust of a pneumatic rock drill is the source of the major part of the noise generated by the drill . The exhaust noise can be reduced in a number of different ways , but this study involved only reactive mufflers . The reactive muffler can be simulated by an electrical circuit . Information obtained from analogous electrical circuits was used to design an efficient exhaust muffler for pneumatic rock drills . Electrical analogies proved to be a valuable tool in the design of mufflers .

Jan 1, 1964

By H. R. Babitzke

The purpose of this investigation was to evaluate the potential of columbium-hafnium alloys as structural materials for use at elevated temperatures. The work described in this report was conducted to determine the properties of columbium-hafnium alloys and to select the more promising ones for further improvement. Properties determined in this report were machinability, hardness, workability, tensile strength, and oxidation resistance. Ten ingots, ranging from 100 percent columbium to 70 atomic-percent hafnium, were prepared and subjected to tests. The test results showed that the alloys with 33 and 50 atomic-percent hafnium were superior in workability, strength, and oxidation resistance. For the alloy series tested, the strength and hardness values increased with the increasing hafnium content. Maximum values were reached with 50 atomic-percent hafnium. The oxidation resistance was poorest at the 1 atomic-percent hafnium level but improved with increasing hafnium content through 70 atomic-percent. Eight of the ten ingots were fabricable at room temperature. The two remaining ingots, those with 5 and 10 atomic-percent hafnium, required hot-working.

Jan 1, 1962

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965