Search Documents

By H. P. Hermance

The Ore Hill zinc-lead mine in Grafton County, N. H., was investigated by the Bureau of Mines from March to July 1943 and from August to October 1944. Fourteen holes with an aggregate bore of 4,899 feet were diamond-drilled, the old workings were unwatered and sampled to an inclined depth of 250 feet, and the tailings dumps were surveyed and sampled. The deposit at the Ore Hill mine comprises a bedding-plane vein of massive sphalerite and galena with subordinate chalcopyrite and pyrite in a series of interbedded metasedimentary and metavolcanic schists about one-quarter mile east of their contact with the intrusive Baker Pond gneiss. The property was first opened about 1850 and was active at times to 1914. Production records are not available, but the output is believed to have been considerable. In 1944, leasers recovered a marketable mica product from mica schist from the dumps and certain outcrops. This report describes the work performed in the Bureau's investigation and presents the data obtained.

Jan 1, 1948

By Leonard Obert

The various underground rooms in the Bureau of Mines Oil-Shale mine, Rifle, Colo., have been open for periods ranging from 3 to 5 years. During this time 3 roof falls have occurred; 1 was induced, and the other 2 were unintentional. The three roof falls are described in this report. Two causative factors are discussed -a time-dependent deterioration of the roof rock and an unfavorable system of jointing that occurred in the strata overlying the present roof horizon. Irrespective of cause, the operating life of any stoping area would have been short com-pared with the life of the roof (1 to 4 in the most unfavorable instance), if a high-production system of mining had been employed. The report is concluded with several recommendations that should be considered in planning future mining operations.

Jan 1, 1958

By Fei-chiu Huang

The principle of time domain reflectometry (TDR) is being used by the U.S. Bureau of Mines to monitor strata displacements induced by mining. The Northwestern University TDR Signature Analysis (NVTSA) Program was developed under contract with the Bureau to allow for visual comparison of three TDR waveforms quickly and easily. This program is interactive, and on-line help is available. The Northwestern University Remote Control TDR Data Acquisition System and Modification of Tektronix SP232 Host Application Program (NUMOD) was then developed to allow acquisition of TDR wave-forms from a remote cable tester via modem. The NUMOD system utilizes commercially available software while the NUTSA program is available from the Bureau. This report begins with a discussion of TDR principles followed by a description of the NUMOD system. An interactive example of signature analysis is then used to demonstrate features of the NUTSA program.

Jan 1, 1993

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety lamps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By Nicholas Kyriazi

It is of interest to know how to obtain as high an absorption efficiency as possible from a CO2-absorption canister used in closed-circuit breathing apparatus. In this study the Bureau of Mines found that varying the bed depth and the cross-sectional area of a canister changes its absorption characteristics. In tests using four ,1 rectangular, variable-depth canisters with different cross-sectional areas, the Bureau found that, given a constant weight of the chemical absorbent, LiOH, and a constant COa input, the canisters with a greater cross-sectional area reached C02 levels of 0.5 volume-percent in the effluent gas sooner than did the canisters with a greater bed depth. However, resistance to flow through the canister increases with bed depth, and a trade-off is inevitable. It was anticipated that the efficiency of a canister would increase with increasing intergranular air space approaching the tidal volume of the breathing waveform and then level off at some point under 100 percent. This postulation was partially substantiated. Cylindrical and radial canisters were also tested and compared. It appears that shape is not as important a factor in absorption efficiency as bed depth, since neither canister differed significantly from the rectangular canisters with regard to absorption efficiency values.

Jan 1, 1980

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By R. K. Clifford

Chalcopyrite (CuFeSz) concentrates produced on the Lead Belt of Missouri typically contain 28 pct Cu and from 0.5 to 1.5 pct each of nickel and cobalt. Most of the nickel and cobalt are present as the mineral siegenite, (Ni,Co)3S4, almost none of which is recovered presently. The Bureau of Mines, U.S. Department of the Interior, has been conducting research on the chalcopyrite to produce a marketable fraction enriched in cobalt and nickel. Ferric chloride leaching of various chalcopyrite (copper) concentrates has yielded residues containing from 10.2 to 16.2 pct Ni and 8.3 to 11.4 pct Co with recoveries of approximately 79 pct. In another approach, laboratory froth-flotation tests have been conducted to investigate the effects of regrinding, roasting, baking, and steaming prior to flotation, with a variety of reagents. The best laboratory results were obtained after regrinding the copper concentrate to 94 pct minus 400 mesh and floating the chalcopyrite at natural pH (6.5) with 0.48 pound of sodium diethyldithiophosphate and 0.01 pound of sodium cyanide per ton of concentrate. This procedure yielded a tailings assaying 20.4 pct Cu, 5.2 pct Ni, and 3.45 pct Co. The tailings contained 67.2 pct of the nickel and cobalt and 15.9 pct of the copper originally in the copper concentrate; the remainder of the values reported to the flotation concentrate, which analyzed 29.6 pct Cu. To verify the laboratory flotation results, a 60 kg/hr process demonstration unit (PDU) was constructed in the Cominco American Magmont mill, Bixby, Mo.

Jan 1, 1978

By M. E. Tyrrell, C. W. Houck

Mixtures of zirconium diboride and refractory metals of group VI were resistance sintered to high - density compacts using modified electric welding equipment . To evaluate the use of chromium , molybdenum , or tungsten as binders for zirconium diboride the sintered compacts were examined in polished sections and tested for crushing strength , hardness , microhardness , oxidation rate , and resistance to mechanical shock . Chromium yielded the highest compressive strength , the greatest resistance to mechanical shock and oxidation , and a satisfactory Rockwell hardness . Molybdenum did not yield a satisfactory cermet . Tungsten yielded compacts having high microhardness but very low mechanical strength .

Jan 1, 1964

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By J. K. Whyatt

The Bureau of Mines, under a cooperative agreement with Callahan Mining Corp., measured rock displacement at the 4,7S0-ft level of the 5,100-ft-deep rectangular, timbered Caladay Shaft in northern Idaho. Displacements were measured with multiple-position borehole exten-someters (MPBX) installed 4 ft above the face and timber extensometers (TE) installed with the timber sets. This report presents the displacement data along with preliminary, qualitative observations of rock behavior. The measured displacements showed an instantaneous response to shaft sinking and significant time dependency. The relative magnitudes of displacement measured at the shaft walls were heavily influenced by local geologic structure and distance from the shaft bottom.

Jan 1, 1987

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010

By T. OnIin, F. F. ApIan

"A study has been made of the surface properties of coals of differing ranks, in their natural state and as modified by the addition of collectors. The evaluation of their surface properties has been done by captive bubble contact angles, water and methylene iodide sessile drop contact angles, zeta potential, point-of-zero charge (PZC) shift, and flotation. .changes in the hydrophobicity of coal is a function of both the rank of the coal and the collecting reagent.INTRODUCTIONThe chemical and physical properties of a raw coal will determine its response to a given beneficiation process. .For such processes as flotation, filtration, flocculation, dispersion, handling, dust supression and agglomeration, however, it is also necessary to consider the surface properties of the coal and mineral matter constitutents of the raw coal. In the case of a specific particle to be floated, it is also necessary to consider the properties of the coal as modified by the addition of some reagent designed to modify (usually increase) the hydrophobicity of the coal surface. General properties of the coal have been well summarized by Van Krevelen (1) and Elliott (2), while the data for the surface properties of coal are much more scattered in the literature (see, e.g.: Parekh and Aplan (3), Gutierrez-Rodrigues et al. (4), Aplan (5), Arnold and Aplan (6), Hogg and Chander (7) and Rosenbaum and Fuerstenau (8)). While a knowledge of the inherent surface properties of a sample are important, of much greater practical significance are the properties of the particle in the presence of a reagent, such as a collector, designed to enhance the hydrophobicity of the particle. This study will focus on the surface properties of coals of various ranks in the presence of a variety of collectors."

Jan 1, 1989

By Philip W. Holland

The Bureau of Mines has developed a trace helium analyzer for deter-mining helium-4 in the parts-per-billion range. The instrument is used for analyzing pure gases, laboratory-prepared standards, and atmospher-ic samples. Accuracy at the 95-pct confidence level in the 50-to 20,000-ppb range is within ±2 ppb or ±0.4 pct, whichever is greater. The minimum detectable helium-4 concentration is calculated to be 5 ppb. The analyzer consists of a modified helium leak-detector mass spec-trometer, a laboratory-built sample inlet system, and a liquid-nitrogen-cooled charcoal trap. A programmable integrator and event-control module make automatic operation possible. The portability of the analyzer allows it to be used in the field.

Jan 1, 1984

By B. J. Moore

This publication contains analyses and related source data for 191 natural gas samples from 22 states and 1 foreign country. Of the total samples, 182 were collected during calendar year 1987. The remainder were collected earlier, but releases granting permission to publish were not received before 1987. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1988

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By Henry G. Dorsett

This report is a description of equipment and test procedures used by the Federal Bureau of Mines in laboratory studies on the explosibility of dusts. The principal tests concern ignition temperature, minimum explosive concentra¬tion, minimum electrical energy for ignition, limiting oxygen concentration, pressure, and rates of pressure rise. As new materials often present unique problems, variations in the general procedure and special tests performed are indicated, The general procedures for handling a dust sample from its receipt at the laboratory to the preparation of the report are described. The repro¬ducibility of the respective tests are shown. A brief history of laboratory studies on dust explosions by the Bureau of Mines and a description of current equipment and test procedures used are presented in this report. Its purpose is to facilitate interpretation of data previously published and those proposed to be published on the numerous mineral, agricultural and industrial dusts that have been studied. Through understanding and interpretation of the laboratory data obtained for the parameters of explosibility, preventive measures can be adopted for alleviat¬ing the hazard of dust explosions arising in manufacturing and processing industries.

Jan 1, 1960

By R. V. Ramani, A. S. C. Owili-eger

? THIS PROGRAM SIMULATES METHANE FLOWRATES THROUGH THE GOAL ? SEAM BY THE GAUSS-SEIDEL ITERATIVE TECHNIQUE. THE MODEL IS A TWO ? DIMENSIONAL SYSTEM. THE ITERATIVE FORM OF THE GAUSS-SEIDEL IS ? OBTAINED FROM A PARTIAL DIFFERENTIAL EQUATION OF FLOW BY CENTRAL ? FINITE-DIFFERENCING APPROXIMATION SCHEME ? NPRESS IS THE NUMBER OF SPECIFIED PRESSURES EXCLUDING ? RESERVOIR AND FACE PRESSURES ? NQUAN IS THE NUMBER OF SPECIFIED FLOW QUANTITY.... EXCEPT FLOW ? OUT OF THE FACE. THIS- QUANTITY CAN BE POSITIVE(INJECTION) OR ? NEGATIVE ( PRODUCTION) ? XPERM(I,J) I S THE DIRECTIONAL PERMEABILITY IN THE X-DIRECTION AT THE POINT (I,J) ? YPERM(I,J) IS THE DIRECTIONAL PERMEABILITY IN THE Y-DIRECTION ? AT THE POINT (I,J) ? RESEP' IS THE RESERVOIR PRESSURE ? FACEP IS THE FACE PRESSURE. THIS PRESSURE IS ASSUMED TO BE ? APPROXIMATELY ATMOSPHERIC ? LENGTH, WIDTH, AND THICK ARE THE ZONE OR MEDIUM DIMENSIONS * PUHL I S A DUMMY NAME FOR VISCOSITY ? DMAXI IS VARIABLE NAME FOR INITIAL MAXIMUM ERROR OF ITERATION ? DMAXF IS A VARIABLE NAME FOR FINAL MAXIMUM ERROR OF ITERATION ? NITER IS A VARIABLE NAME FOR STORAGE OF NUMBER OF ITERATIONS ? RAD IS A VARIABLE NAME FOR THE SPECTRAL RADIUS OF THE GAUSS¬ ? SEIDEL MATRI-X. THIS PARAMETER ALSO MEASURES THE RATE OF ? CONVERGENCE OF THE ITERATION ? KOUNT IS AN ITERATION COUNTER ? MAXIT IS THE MAXIMUM NUMBER OF ITERATION SPECIFIED BY THE USER # EPS IS THE MAXIMUM RESIDUAL ALLOWABLE ERROR-FOR CONVERGENCE

Jan 1, 1974