Search Documents

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977

Provide d comprehensive source of up-to-date information about technology for revegetating coal mined lands. Approach A great deal of activity and research in the field of coal mine revegetation has been reported in technical literature, both before and after the passage of Public Law 95-87, the Surface Mining Control and Ruclamation Act of 1977 (SMCRA). This information is widely scattered throughout books, scientific journals, periodicals, Government reports, and other sources, and there has been a need to develop a method of accessing it quickly and efficiently. At the request of the Office of Surface Mining Reclamation and Enforcement which promulgates and enforces regulations implementing the act, the Bureau of Mines has prepared a document that identifies literature relevant to coal mine revegetation. Most of the literature available on this subject has been published during the past 15 years. To tap this reservoir of information, 14 data bases were accessed from DIALOG SDI (Selective Dissemination of Information) Service using three keyword combinations (surface mining and reclamation, strip mining and reclamation, and revegetation). This procedure generated over 7,000 listings. The U.S. Department of Energy's ENERGY data base was selected from the 14 DIALOG bases, both for its large number of listings and for its broad coverage of literature. This data base contains all the unclassified information that passes through the Technical Information Center of the Department of Energy, including reports, journal articles, conferences, patents, books, monographs, theses, and engineering materials relating to energy development.

Jan 1, 1986

By C. M. K. Boldt

This report summarizes five separate Bureau of Mines contract studies on the use of aerial photogrammetry, satellite transmission of in situ instrumentation information, and satellite imagery to monitor and update mine waste embankment data. The equipment used, methods applied, results, recommendations, and cost analyses are presented along with a bibliography of related investigations.

Jan 1, 1987

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By R. S. Sanford

The Muir Inlet or Nunatak molybdenum deposits arc in the Glacier Bay district, Muir Inlet, miles northwest of Juneau. The deposits were examined by Bureau of Mines engineers, and the area was mapped by a field party of the Federal Geological Survey during the summer of 1942. 5/ The following year the Bureau of Mines began developing the deposits. A total of 217 channel samples were taken, and 2 diamond drill holes totaling 256 feet wore drilled. The samples were sent to the' Bureau's laboratories at Rolla, Mo. for beneficiation.

Jan 1, 1949

By W. A. Cole

This report covers the preliminary phase of an investigation of clays, shales, and certain rocks in Wisconsin to determine the feasibility of processing lightweight aggregate in the State. The study was extended to include rotary-kiln testing of a limited number of shale samples, and to an appraisal of the Maquoketa shale resources in eastern Wisconsin. A total of 45 samples of clays, shales, and other argillaceous rocks of Wisconsin were tested. The lower Maquoketa shale is the only material found to date that offers possibilities as a source of material that can be processed in a rotary kiln for lightweight aggregate. Bedrock occurrences of the Maquoketa shale are found in the eastern and southwestern parts of the State. The populous southeastern region of Wisconsin presents a large potential marketing area for lightweight aggregate. For this reason special study was directed to the Maquoketa shale in the eastern district.

Jan 1, 1961

By Richard F. Link

The principal procedures for the statistical analysis of gold assay and other trace-element data depend on applying either the normal frequency distribution or the lognormal frequency distribution. The consequences of applying both methods are examined through reference to example data from United States and South African gold mines. It is concluded that for estimation of average grades, except for certain data with a very high coefficient of variation (ratio of standard deviation to mean), use of the lognormal distribution is ordinarily undesirable because bias may be introduced and little efficiency can be gained. However, if biased average grades can be tolerated, as in the examination of data from surveys in exploration geochemistry, use of the log-normal distribution may be desirable. Various statistical analyses are detailed, and the tables presented to implement the analyses are more complete than those previously published.

Jan 1, 1971

Provide a means for reliable in situ stress change measurements in soft, friable geologic materials under high stress. Background Effective mine design requires a knowledge of changes in rock stress generated by a mining operation. In situ stress measurement can provide a means of obtaining this knowledge from an active mine for the ultimate purpose of design verification and analysis. The Bureau of Mines has designed and tested a device for measuring changes in rock stress-the borehole platened flatjack (BPF). It has found application in investigating stress anomalies due to geologic structures, stress concentrations from multiple seam interaction, and stress abutments from pillar retreat and longwall mining.

Jan 1, 1990

By James V. Kelly

During the spring and summer of 1947, the Bureau of Mines conducted an investigation and core-drilling program in the vicinity of the Rodham mine, approximately 4 miles north of Shullsburg, Wis. This work was undertaken as a part of a general study of the zinc and lead-producing area of southwestern Wisconsin. Work in the Rodham-mine area was done to investigate further a mineralized area frilled in part by the Puritan Exploration Co., a Delaware corporation, with offices in Galena, Ill. Some significant lead-bearing samples were obtained, but no continuous ore body was disclosed as a result of the Bureau of Mines work.

Jan 1, 1949

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By M. R. Peterson

The U.S. Bureau of Mines investigated column flotation for recovery of a high-grade fluorite (CaF2) concentrate and byproduct concentrates from the Fish Creek fluorite deposit in Eureka County, NY. The recovery scheme consisted of (1) grinding the ore to minus 48 mesh, (2) fluorite rougher and cleaner flotation, (3) desliming the rougher fluorite flotation tailings at 20 Jjm, (4) mica flotation, and (5) silicate rougher flotation. Acid-grade fluorspar, mica, free silica (Si02) sand, and low-grade beryl (Be3Al2S~018) concentrate were produced in a 100 lb/h continuous column flotation unit (CCFU). The highest results achieved were %.6-pct CaF2 recovery in a fIrst cleaner concentrate containing 99.7 pct CaF2. Beryl recovery was as high as 92 pct at a grade of 5.3 pct BeO. The silica sand, which assayed 98 pct Si02, was recovered as the rougher beryl flotation tailings. Collector reagent consumption was reduced 45 pct for fluorite and 58 pet for silicate flotation in comparison with bench-scale conventional flotation. All products were signillcantly improved in both grade and recovery over conventional flotation results, and the recovery scheme was simplifIed by removal of several stages of flotation in the fluorite and silicate flotation steps.

Jan 1, 1990

By C. M. K. Boldt

This U.S. Bureau of Mines report presents a study of three typical tailings samples as potential cemented backfill in underground mines. The testing series was unique in that the pulp densities of the samples were all above 75 pct solids. Test results included dry density; slump; percent settling after 28 days of curing; tensile strength after 28, 120, and 180 days of curing; and unconfined compressive strengths after 7, 28, 120, and 180 days of curing. The physical properties of the various test mixtures were further analyzed using linear and nonlinear statistical methods to produce correlations and mathematical equations. Physical properties were used to determine the influence of mix additives and as input for numerical modeling studies of backfill. The mathematical relations were used as a predictive tool in determining the suitability of various materials as backfill.

Jan 1, 1989

By T. D. Ralston

This Bureau of Mines report presents a mathematical model for heterogeneously catalyzed chemical reactors operating under turbulent conditions. The model includes reaction kinetics on the catalyst surface as well as diffusion of the reacting components within the reactor. Three applications of the model to tube-wall methanation reactors are discussed. The first application is a computation of catalyst activity from measured reactor data. This result is then used in a reactor sizing problem and a problem of reactor simulation with recycle. In addition to the reactor model, a novel approach to solving the recycled reactor problem is given.

Jan 1, 1974

Improve the safety of mine workers by developing a sensitive ground-fault relay system capable of detecting and isolating low level ground faults and thereby minimize the danger of electrocution. Approach Inadvertent, direct contact with energized conductors in underground coal mines is a major cause of electrocutions. Although relay systems designed to protect workers against such fatal accidents do exist in some industries, there are no effective ground-fault-sensing relay systems that address the special problems presented by power systems designed for U.S. mines. The Bureau of Mines conducted research to design and construct a sensitive ground-fault relay for use with low-voltage, alternating current (ac) mine electrical systems. Such a relay, sensing current leakage or faults in an electrical system, would send a trip signal to a circuit interrupting device which would then shut down power.

Jan 1, 1986

By Ivan F. Avery

OUTPUT of carbon black in 1959 increased in all producing States except New Mexico. The national increase was 20 percent. Domestic sales and exports increased 22 percent and 16 percent, respectively, resulting in a 21 percent gain in sales. Sales to the rubber industry, which purchased 95 percent of the domestic output of carbon black, increased 23 percent. Sales to all other major consumers also increased. Stocks decreased 82 million pounds during the year. [ ]

Jan 1, 1960

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today's environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980