Search Documents

By W. D. Ludemann, E. A. Loria, E. A. Rowe

The isothermal recrystallization of electrorefined vanadium has been studied as a function of annealing time , temperature , and prior deformation . Specimens were cold- rolled from 30- to 75 - percent reduction in thickness , then annealed from 700 ° to 1,200 ° C at time periods ranging from 1 minute to 96 hours . The course of recrystallization was followed by means of hardness , metallographic , and X- ray techniques , and a recrystallization diagram was constructed . Interpretation of the data indicated that there was around 50- percent softening due to recovery ( first stage of softening) before recrystallization began . The defining of recrystallization limits with respect to the amount of deformation was precisely established for electrorefined vanadium . More than 30- percent reduction was necessary for recrystallization to occur at 850 ° C. With 60- percent reduction , it was initiated at 750 ° C and completed at 950° C. The activation energy for recrystallization , as derived from the data , was 95,300 cal per mole for 60 - percent reduction and annealing at 750 ° to 900 ° C. Recrystallization by the mechanism of nucleation and growth was the principal process during the second stage of softening . minor part of the second stage of softening took place as strain- induced boundary migration , which was observed in specimens reduced 30 percent , bent in L- shape , and annealed at 950 ° C. Grain size decreased significantly only with the largest reductions and annealing between 750 ° and 950 ° C. Grain growth was expressed by the empirical relation D = KKtt"" ,, the exponent being the same at 60- percent reduction and annealing from 750 ° to 900 ° C. Accordingly , the activation energy for grain growth was 75,000 cal per mole .

Jan 1, 1964

By R. Hogg, T. F. Dumm

"A procedure for evaluating the size/specific gravity distribution of ultrafine coal and the distributions of sulfur and ash with respect to particle size and specific gravity is described. The procedure is essentially an extension of the conventional coal washability technique in which special precautions are taken to ensure particle dispersion in the heavy organic liquids, centrifuges are used to obtain adequate separation rates, and micromesh sieves are used for size separation at fine sizes. An example of the application of this technique to the evaluation of the extent of liberation of sulfur and ash in a coal sample ground to 90Z passing 200 mesh (74 um) is described.INTRODUCTIONIn order to determine the potential for deep cleaning of coal by fine grinding to liberate sulfur and ash-forming minerals, it is necessary to obtain data on the distributions of these species by size and specific gravity. In conventional coal processing operations, this information is obtained by means of a standard ""washability"" analysis. Attempts to extend this procedure to ultrafine coal, however, have generally been unsatisfactory and have often led to unreliable and inconsistent results [11. The present authors have described a modified washability procedure in which cumulative specific gravity fractionation is combined with sub-sieve size analysis (by laser diffraction/light scattering) to determine the particle size/specific gravity distribution of ultrafine coal [2]. Unfortunately, because this technique does not involve separation of the individual fractions, only limited information can be obtained on the specific distributions of sulfur and ash.The objective of the work described in this paper was to develop and evaluate a procedure for size and specific gravity fractionation of ultrafine coal and to use conventional analyses for sulfur and ash to determine their relative distribution in the coal. The procedure is essentially a simple extension of the standard washability analysis [3] but incorporating special precautions for treating ultrafine particles.EXPERIMENTAL Material The material used in the development and evaluation of the ultrafine coal fractionation procedure was a medium volatile bituminous coal from the Lower Kittanning seam. A sample of the coal (nominally - 1/4 inch), obtained from the Penn State Coal Data Base, was ground to 90% passing 200 mesh by the following two-stage grinding procedure: About 2 kg of the as-received coal were ground to about 30Z passing 200 mesh in a Model 4-E Quakertown mill (""coffee grinder""). About 1 kg of this product was then ground to about 90Z passing 200 mesh in a Holmes Model 300 Pulverizer."

Jan 1, 1989

By G. S. Scott

The flammability of trichloroethylene vapors in air has been determined in a 7-inch cyclindrical vessel. Saturated flammable mixtures were formed with air at atmospheric pressure between 30° C (86° F) and 82° C (180° F); the trichloroethylene concentrations at these temperatures are 12.5 (lower) and 90 (upper) volume-percent, respectively. Further study is necessary to assess the effects of different variables on the flammability of this material. INTRODUCTION Trichloroethylene (TCE) (ClHC = CCl2), sold under various trade names (Blacosolv, Perm-A-Clor, Tri, Triad, Triclene, Trivec, Tromex, Vapoclean, Vapoclor, Westrosol, etc.), is an important industrial chemical. A summary of its physical and chemical properties is given in table 1. It is used to degrease metals, leather, and textiles, to extract residual oils from vegetable oil cakes, for dry cleaning, and in soap. It is a powerful solvent for fats, resins, bitumens, rubber, sulfur, and phosphorus. Several explosions in which trichloroethylene was involved prompted an investigation by the Bureau of Mines to determine the conditions under which such accidents can occur.

Jan 1, 1963

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By E. Morrice

The Bureau of Mines investigated methods for beneficiating platinumgroup metal ores from the Stillwater Complex , Montana , as part of its program to increase the supply of critical and strategic minerals and metals from domestic resources . This report presents results of a 5- day continuous campaign employing a pilot flotation mill to recover sulfide concentrate containing platinum- palladium values from anorthositic ore . A mercaptobenzothiazole - sulfuric acid reagent suite was used . The pilot flotation mill was operated at an average feed rate of 106 lb/ hr of ore . A rougher concentrate containing 8.5 pct of the feed was prepared ; it assayed 1.1 oz /ton Pt and 3.5 oz / ton Pd . Recovery of platinum and palladium were 91 and 87 pct , respectively .

Jan 1, 1965

By Terry J. Kreidler

In recent years, west-central Arizona and adjacent California have become the focus of geologic and exploration attention because of its excellent exposure of detachment-fault terrane. Detachment faults, normal faults with nearly horizontal fault planes, are the result of regional extension. Rocks on the lower plate consist of mylonitized intrusive, metasedimentary and crystalline rocks highly altered to chlorite; upper plate rocks comprise sedimentary, volcanic, metasedimentary, and metavolcanic rocks. The movement of the detachment fault causes the rocks on the upper plate to be severely fractured and brecciated thus making them Ideal conduits for mineralizing fluids. Mineralization favored the more reactive sedimentary and volcanic rocks of the upper plate. Three gold deposits, located in upper plate rocks, are currently being mined along the Colorado River corridor: the Picacho Mine near Yuma, Arizona, 70 mi south of the study area; the American Girl Mine In southeastern California, 60 mi southwest; and the Copperstone Mine near the southern end of this study area. Samples from the above three mines were used to create a geochemical model of detachment-related gold deposits. Antimony, arsenic, barium, copper, mercury, molybdenum, manganese, tungsten, and zinc all occur In the mine samples in concentrations at least three times greater than found elsewhere in similar rock types. Samples taken by the Bureau from the wilderness study areas contain similar anomalous concentrations of the same elements as well as elevated concentrations of several other elements Including: lead, fluorine, cerium, uranium, and samarium.

Jan 1, 1992

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By Richard H. Otto

Three longwall mining methods practiced in foreign countries are described that have potential for increasing underground recovery and productivity in thick coalbeds of the Western United States. The methods are multislice long-walling, longwall caving, and high-face longwalling. Foreign practice and possible application in the United States are discussed.

Jan 1, 1979

By Hillary W. St. Clair

Reaction rate coefficients were determined from analyses of the effluent gas for the reduction of granular ferrous oxide to metallic iron by passing carbon monoxide through a packed bed of oxide at a controlled rate in the temperature range 1,000° to 1,300° C. Coefficients were determined by the comparison of observed analyses and calculated analyses using a mathematical model that takes into account the nonuniform composition of both the solid oxide and the gas. A method is also given for finding the value of the rate coefficient that best fits the observed data.

Jan 1, 1968

By Carlton E. Brown

[The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted. in South Africa about 19164/ and more recently in England5/,6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting.]

Jan 1, 1938

"Fire fighting in metal mines under the best of conditions is a dangerous, a slow, and a difficult task. Certain gases generated from combustible material burning in restricted areas are poisonous, even in small quantities, and can not be breathed without serious and often fatal results. In addition to poisonous gases, smoke is given off which obscures the vision of the fire fighter and frequently prevents him from gaining access to the fire area. Many fire-fighting crews have had to turn back because their vision was so impaired by the dense smoke that the fire area could not be located and there was danger of them becoming lost in the mine.In mines having mechanically controlled ventilation - that is, mines not dependent entirely upon natural air currents - the gas and smoke can be forced ahead of the fire-fighting crews, thereby facilitating exploration of the mine and saving the time, energy and oxygen of the mine rescue apparatus crews.Where currents of fresh air can be circulated up to points near the fire without danger of seriously spreading the fire, fresh air bases can be established in the immediate vicinity, and a more intelligent campaign for fighting or controlling the fire can be mapped out.Positive air currents through forced ventilation may also result in saving the lives of miners who otherwise might have been trapped in smoke and poisonous gases.It is generally known that comparatively few metal mines have attempted to regulate or control air currents, with the result that when a fire occurs underground, the normal ventilation may be reversed, short circuited, or the air current may be in one direction one minute and in the opposite direction the next; or, generally speaking, the ventilation can not be depended upon, and smoke and poisonous gases may accumulate in any part of the mine or ""drift"" on the fire-fighters or on the miners endeavoring to escape."

Apr 1, 1921

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By L. B. Pankratzt

The heat capacity of dimo1ybdenum carbide (Mo2C) was measured from 51° to 298° K, and the entropy at 298.15° K was evaluated. Heat content measurements above 298.15° It were conducted for dimolybdenum carbide (M0caY) and monotantalum carbide (TaC). The results were combined with known heats of formation and the 298.15° K entropy for TaC to obtain values of the heat and free energy of formation from 298.15° K to 1,400° K for MoaC and from 298.15°K to 1,800° K for TaC.

Jan 1, 1966

By Oleg Terichow

The Bureau of Mines studied the penetration of a slender cylindrical tube into a sand bed, simulating seafloor material under the application of a static load. The factorial experimental design was based on three factors: tube diameter, geometry of penetrating bit, and seawater saturation of sand, all of which were found to be significant in influencing the depth of penetration. The geometry of the penetrating bit, or shoe, is of major significance in the mechanics of penetration and should be considered the most important factor for additional study. Linear regression analyses of the load-penetration data show that the relationship is linear.

Jan 1, 1970

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By Beverly W. Dunning

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel. Data obtained from melts of 1-1/4 to 20 pounds indicate that vacuum melting decreases the number and size of nonmetallic inclusions and at the same time increases the degree of dispersion of the remaining inclusions. These improvements are undoubtedly related to the elimination of approximately 80 percent of the nitrogen and 90 percent of the oxygen as well as most of the undesirable metallic trace impurities.

Jan 1, 1961

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979