Search Documents

By Leonard Obert

This report presents evidence indicating that when rock is stress-relieved during the course of mining or in drilling a core, it may be altered or damaged to the extent that the physical properties of the relieved specimen are not the same as those of the in situ rock. Furthermore, this type of damage may result from stress change other than that accompanying stress relief, such as the application of a relatively large compressive stress. In some instances the damage is microscopic, manifesting itself as incipient cracks or the failure of individual crystal bonds. However, if the sample is taken from a high-stress area, macroscopic damage may occur.

Jan 1, 1962

By D. Randolph Berry

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller, Inc. to develop guidelines for the storage and use of Self-Contained Self-Rescuers (SCSRs) in underground non-coal mines. An SCSR is a device capable of supplying, in an emergency, one hour of self-contained oxygen (no breathing of mine air). The information and recommendations in this report were developed primarily from three sources: discussions with mine representatives (including management, labor, and government), site visits in underground mines I and a detailed analysis of every reported non-coal accident which produced d hazardous atmosphere during the 5-year period 1976-1980 -plus ten other major incidents from prior years. Volume IV has three major sections: Recommendations and Discussion (Section 2), Analysis of Mine Accidents (Appendix A), and a Summary of Discussions with Mine Representatives (Appendix B).

Jan 1, 1983

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By R. Q. Shotts, H. J. Hager, A. C. Richardson, G. D. Coe

"INTRODUCTION In the State of Alabama few mines produce coal clean enough to be marketed directly without being washed. This is particularly true where the coal is to be used for the production of metallurgical coke. In washing plants where single-compartment jigs alone are used to treat a large range of sizes, it has been found that the washed coal finer than 1/4-inch contains a large proportion of free impurities and is much higher in ash content than are the coarser sizes. To reduce the ash content of this fine material with jigs usually entails a greet reduction in capacity and a loss of coarse coal in the refuse. This investigation, conducted by the Southern Experiment Station of the United States Bureau of Mines in cooperation with the University of Alabama and the Alabama By-Products Corporation, was undertaken to determine whether the fine washed coal from jigs could be economically re-treated on coal washing tables.COALS TESTEDThrough,the cooperation of the Alabama By-Products Corporation, samples of fine-sized washed coal were obtained from their washeries at Bradford and Gamma.The Bradford mine, on the Black Creek bed, yields a low-ash, medium-volatile coal with fairly good coking properties. This coal is blended with coal from the Mary Lee bed for coking purposes and compensates for the high ash content of the latter. The Black Creek bed is about 30 inches thick and seam analyses show an ash content of from 2.0 to 4.0 per cent. In the Bradford mine the undercut is about 6 inches high, so that a large proportion of fines is produced."

Apr 1, 1932

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covers 54 brands of gasoline represented by 1,480 samples plus those from the Pacific Coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Several changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas and western Tennessee. The Rocky Mountain areas have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico, and El Paso, Tex., have been combined to represent the South Rocky Mountain district. The Cleveland district has been expanded to include Ohio an,"- Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippi, and northern Florida.

Jan 1, 1938

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By S. L. Crouch

An important class of mining problems involves excavations in planar seam or vein-type deposits. In many instances it can be assumed that the seam is at 'infinite' depth in a homogeneous, isotropic or transversely isotropic, linearly elastic rock mss, and that the normal to the plane of the seam is a principal stress direction. Rational planning of excavations in such deposits requires a knowledge; of the stresses and displacements induced by complicated, irregular excavation geometries in the plane of the seam. This problem previously has been solved either numerically or by means of an electrical resistance network analog. Both of these methods effectively simulate the mined portions of the seam as a dislocation in an otherwise continuous mass, and determine the complete solution in terms of the stresses and displacements at the seam. In both cases, the plane of the seam is divided into a number - say, M x N - of squares, and the solution to the problem is determined in terms of the solution to an M x N system of equations. The numerical approach requires that these equations be solved explicitly, while the analog; solves them instantaneously with current analogous to stress and voltage to displacement. A purely numerical solution of practical problems can require a substantial amount of computer time, particularly in situations that demand some sort of sequential analysis, either due to successive mining or to nonlinear behavior of the seam material. This report describes a combined analog-digital computer system for solving problems that are impractical when either device is used separately. The digital computer and the analog are interfaced so that the digital computer can receive information from the analog via a switching matrix and an analog to digital converter, and can activate points of the analog via another switching matrix and a set of digital to analog converters. The resulting hybrid system can be used to simulate arbitrary "stress-strain" characteristics for any portion of the seam by an iterative procedure similar to the initial strain method used in nonlinear finite element analysis. Thus, the hybrid system combines the speed of analog computation with the decision-making capability of the digital computer: the analog instantaneously solves the set of equations, and the digital computer decides how the initial strains must be altered for the solution to be compatible with the prescribed "stress-strain" characteristics for the seam material. The hybrid computer system has many implications for rational planning of underground excavations, since it allows practically any type of inelastic seam behavior or artificial support characteristics to be simulated. Inelastic seam behavior, for example, might be due to either rock failure or to time-dependent deformation.

Jan 1, 1974

By William R. Wayment

The objective of this investigation was to obtain data on friction-head losses of sand slurries during their transport in pipelines. The data ultimately will be used in designing hydraulic transport systems. Information that was incidental to the primary objective was gathered on degradation, changed percolation characteristics, and critical velocities of the slurries~ Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Approximately 2,000 tests were run in the pilot plant. The ranges of flow velocities used in the experiment were 2.8 to 19 f.p.s. in the 2-inch line, 4 to 14.5 f.p.s. in the 3-inch line, and 4 to 11 f.p.s. in the 4-inch line. Velocities were varied in increments of 0.5 f.p.s. through the entire velocity range in each pipe size. Densities were varied in 3-percent increments from 40 to 70 percent solids by weight except for one series of tests in the 2-inch line; in this series, densities were varied in 5-percent increments from 5 to 65 percent solids by weight.

Jan 1, 1962

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

The contract for the Water Jet Chock Mounted Miner Feasibility Study was awarded to FMC Corporation's Advanced Products Division on 18 November, 1974. The program was divided into four phases as follows: ? Phase I - Planning ? Phase II - Conceptual Design ? Phase III - Budgetary Cost Estimate and Economic Feasibility Study ? Phase IV - Final Report During Phase I, which lasted 1 month, most of the necessary information and data for the conduct of Phase II was obtained. To accomplish this, arrangements were made for personal visits to the University of Missouri at Rolla, Illinois Institute of Technology Research Institute, USBM TCMRC, Alpine Equipment Co., Mining Progress, Inc. and Eastern Associated Coal Corporation's Harris No. 1 Mine. Also, a list of manufacturers of high pressure equipment was compiled to be contacted during Phase II. Finally, the objectives to be accomplished during Phase II were outlined. The Phase I Report was submitted on 23 December, 1974. At the beginning of Phase II, personal visits were made to the research centers and firms mentioned above. Later an additional visit was made to the Harris Mine, and to the Pittsburgh Mining Research Center at Brucetun to observe a test of a water jet mounted on an Alpine Mining Machine. Equipment manufacturers of high pressure components such as hoses, tubing, valves, pumps, and intensifiers were contacted to obtain item performance data, availability, and cost.

Jan 1, 1975

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By D. Harry Chambers

The Bureau of Mines, through a memorandum of agreement with the Department of Defense, conducted research to recover silver from aircraft scrap. Silver was recovered by an electrolytic method from stainless steel honeycomb sections separated from the aircraft. These sections had been constructed by sandwiching a stainless steel honeycomb core between stainless steel sheets and then brazing the assembly with a silver alloy. Over 300 pounds of silver was used in the B-58 bomber, concentrated in certain honeycomb sections of the aircraft. Following shredding of the aircraft parts, an average of 95 percent (ranging 67 to 100 percent) of the silver was recovered in a single electro-refining step. After the electrorefined product was magnetically cleaned, purity of the recovered silver was greater than 99.3 percent.

Jan 1, 1980