Search Documents

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By G. L. Oldright

The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of leach rich slags, of viscous slags, and of low capacity in smelting.

Jan 1, 1934

By M. D. Carver

The purpose of this investigation was to determine the effects of variations in content (near the residual level) of the impurities aluminum, nitrogen, manganese, and copper on the corrosion rate in pressurized hot water and in pressurized steam of zircaloy-3, a zirconium-base alloy of 0.25 percent tin and 0.25 percent iron. Thirty-five 10-pound ingots were cast with the appropriate additions of impurity elements, and these were converted to wrought sheets. These specimens were then tested both in water and in steam. The analysis of the resulting data showed that in environments of either pressurized hot water or superheated steam, corrosion rates increased with increasing content of aluminum, nitrogen, or manganese, but were not affected by variations of copper. The effects of aluminum and nitrogen were found to be greater than the effect of manganese. INTRODUCTION At the request of the Atomic Energy Commission (AEC) in August 1956, the Federal Bureau of Mines, in cooperation with Bettis Plant of Westinghouse Electric Corp., began investigating the effects of certain impurity elements on the corrosion rates of zircaloy-3 in pressurized hot water and in pressurized steam. It was necessary to know these effects in order to set control limits on residual impurity levels in zirnaloy-3, intended for heat transfer service in the nuclear reactor of the pressurized water type. A factorial expert it was designed by Westinghouse statisticians. The Atomic Energy Commission provided raw zirconium sponge purchased from Wah Chang Corp. The Bureau's laboratory at Albany, Oreg., made material of different combinations of impurity levels and subjected the material to corrosion tests. This report will describe the work done at the Bureau laboratory and will show, quantitatively the effects of different residual levels of aluminum or nitrogen, or manganese or copper on corrosion rates.

Jan 1, 1961

By D. E. Hirsch, J. W. Davis, Norman G. Foster, F. G. Schwartz

This investigation was undertaken to identify nitrogen , oxygen , and sulfur compounds (polar components ) found in catalytically cracked distillate fuel . It is significant that these compounds concentrate in the sediments and gum that form when the fuel is stored . The polar components were divided in three portions by elution from a chromatographic column filled with alumina . After the hydrocarbons were washed through the column with pentane , a benzene eluted extract was removed followed by an ether eluted extract and then an alcohol desorbed fraction . These extracts were individually distilled in a molecular still and the fractions were analyzed by gas chromatography , mass spectrometry , infrared spectrometry , and elemental and functional analyses . Naphthalene and its homologs , phenanthrene and its homologs , and other compounds such as methyl indene , C₂ quinolines , phenyl indan , and the benzothiophenes , appear in the benzene extracts . Quinolines are the major components of the lower boiling fraction of the ether extract , although carbazoles , acridans , and indoles are present in some concentration . Elemental and functional group analyses of the alcohol fraction indicated 10 percent of the distillate portion was nonhydrocarbon , and in this portion the average molecule contained more than one nonhydrocarbon element . Compounds of such complexity are not well known , and standards for positive identification are limited .

Jan 1, 1963

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2 ) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs' estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By F. E. Brantley, D. M. Yergensen, D. A. Martin

Fluidized - bed roasting was investigated as a means of decomposing gypsum and gypsum mixtures to produce a gas rich in sulfur dioxide and a lime or portland cement residue . Ninety- eight percent desulfurization of gypsum in a 10 - inch fluidized- bed reactor took 1.5 hours at an operating temperature between 1,200 ° and 1,225 ° C. A cement- type residue was obtained but had to be refired at 1,450 ° C before mortar prepared from it met the physical specifications for cement .

Jan 1, 1963

By Raja V. Ramani, Sachin Shankar

"Re-entrainment refers to dislodgement of particles deposited by both atmospheric and nonatmospheric processes and their subsequent insertion into a flowing field. Formation of sand dunes, snow drifts, soil erosion and fugitive dust emissions are a few examples of the natural occurrence of re-entrainment. Re-entrainment studies have been done for the estimation of potential hazards from nuclear fallouts. The phenomenon of re-entrainment has been utilized for the cleaning of wafers and filters. Re-entrainment is associated with both surface and underground mining activities. However, studies on dust re-entrainment in mine atmospheres are limited. Understanding the re-entrainment phenomenon is important because dust particles lying seemingly harmless on the ground and adhering to numerous surfaces can get re-entrained and become a health and safety hazard.There are significant differences in the kind of re-entrainment encountered in underground mines and those in other fields of interest. These major differences are air velocity, direction of air flow, particle size, amount of particles, and time of exposure. While numerous studies have been done in other fields to identify the role of interacting variables and their contribution to the mechanisms of re-entrainment, no similar reported work is available for dust in mine atmospheres.In this paper, recent research efforts on re-entrainment are reviewed. The most suitable form of representing re-entrainment in underground coal mine atmosphere is presented. Various approaches to studying re-entrainment phenomenon in mines are also outlined.In the mineral industries, formation of dust particles of widely varying sizes is a natural outcome of the fragmentation required in mining the solid resources. Fine particles in mine atmospheres, particularly in the respirable size range, are a threat to the health and safety of the miners when present in high concentrations. In 1980 the National Academy of Sciences (NAS) Committee on the Measurement and Control of Respirable Dust in Mines recommended that the spatial and temporal characteristics (of fragments produced in coal mining) need to be understood so that the exposure of workers to the dust can be controlled. Recently several studies have been performed to understand the fundamental behavior of the airborne respirable dust in mine airways (Bhaskar, 1987; Qin, 1988; Polat, 1989; Bode, 1990)."

Mar 1, 1992

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By S. R. Wilson

[The Anniversary-Bucky pegmatite is one of the largest, dikes in the Quartz Creek district, 21 miles east of Gunnison, Colo. The major dike consists of quartz-albite pear pagmatite and graphic granite with many quartz masses as individual cores occurring within the dike. A mining operation on one of the largest core areas has exposed several mineralogic cones directly associate with the core. These zones, including the large- units of the dike, are quartz pegmatitc, quartz-perthite pegmatite, perthite pegmatite, muscovite-feldspar -quartz pegmatite, quartz-albite pegmatite, and perthite-quartz (graphic granite) pegmatite. Muscovite and beryl are found in the muscovite-feldspar-quartz zone and are the only two products that have been marketed. Other potential products are perthite, graphic granite, and possibly small quantities of columbite-tantalite, monazite, and related radioactive minerals. The Bureau of Mines drilled two diamond-drill holes during April 1950 to investigate the largest and cost promising core area. This, report describes the results of this drilling.]

Jan 1, 1953

By P. M. Sullivan

Galvanizers' sal skimmings have been treated by two methods of leaching in attempts to produce preflux solutions suitable for use in galvanizing operations. Both water-leaching and acid-leaching procedures are effective, except in severely exhausted skimmings when water-leaching becomes impractical. A preliminary analysis of the skimmings is not required. Solutions in the recommended concentration range can be produced conveniently by control of pH, specific gravity, and chlorine content. A technician would require only a short period of training to be able to perform the operations described.

Jan 1, 1958

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By Barry L. Warner

This program involves the evaluation of means for suppressing fires on underground coal mine conveyor belts. Full scale conveyor belt fire tests were conducted to determine the requirements of automatically actuated water sprinkler, high expansion foam, and multi-purpose dry powder extinguishing systems, and of various fire detection devices, necessary to adequately protect underground belt heads. The program included the development of a suitable MI scale conveyor belt test fire, conducting of fire tests in which extinguishing and detection systems and equipment were evaluated, and testing to evaluate the effects of the coal mine environment on detection equipment. Preliminary testing conducted to develop a suitable test fire revealed that fire can propagate on some conveyor belting classified as fire-resistant. New fire-resistant PVC and new non-fire resistant rubber belts were used in the full scale fire tests. These tests indicated that a single branch line sprinkler system with relatively low water pressure provides adequate belt head protection. High expansion foam and multi-"purpose dry powder extinguishing systems as presently specified by regulation were found to be suitable for belt head protection, although care is required with powder systems to assure adequate distribution. Thermal type detection devices were found to be most practical for conveyor belt protection, with combustion products and optical detection methods having serious disadvantages.

Jan 1, 1974

By Irving Kabik

Chlorates and perchlorates, when mixed with certain reducing materials, may give a detonating explosive of considerable power. Concerning explosive chlorate mixtures, Guttman3/ states that they "have at all times fascinated inventors on account of the large amount of oxygen stored up in potassium chlorate, which can be given off so readily. When Lavoiser and Berthollet tried to make a chlorate powder in a stamp mill in 1788, they made a great show of it, and even two ladies were present. Unfortunately, after a certain amount of pounding the powder exploded and killed an official and the daughter of the Government commissary, who assisted at the experiments.***. It is interesting to observe how the same old mixtures are proposed over and over again with slight alterations only, in order to qualify for a patent. Potassium chlorate with some carbonaceous matter like charcoal, sugar, starch, glycerin, flour, or sometimes a vegetable or mineral oil and the like occurs again and again." Sprengel explosives, in which some of the undesirable sensitivity of the chlorate was minimized by coating the crystals with a liquid reducing agent, received some attention after a patent was issued to Dr. Herman Sprengel in England in 1871.4/ A somewhat similar explosive, known as Rack-a-

Jan 1, 1945

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Glenn C. Reed

"Preliminary examination of the Glass Buttes mercury deposits, Lake County, Oregon, was made in August 1945 at the request of W. S. Lazier, present lessee of the deposit.Most of the prospect openings in the area were inspected. The more significant workings were sampled and napped in detail. This report presents the data obtained from the investigation to date.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. noon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. P. S. Dean, assistant director.Special acknowledgment is due to S. H. Lorain, chief, Albany Division, Mining Branch and to S. R. Zimmerley, chief, Salt Lake City, Utah, Metallurgical Division, for analyses of the ores.The presence of quicksilver in the Glass Buttes district has been known since about 1930. The area immediately north of Middle Butte has been superficially prospected by numerous test pits, trenches, shafts, and short adits, which revealed a number of opalized zones. Many of these opalized zones contain weak to strong concentrations of cinnabar. The area has not boon explored thoroughly; no mercury has been produced from any of its deposits.A block of 48 full-size claims has been located to cover a large part of the area in sections 34 and 3, Tps. 23 and 24 S.,R. 23 E.,W.M. These claims, held by, location are owned by H. S. Miller, lumberman of Bend, Ore. W. S. Lazier, 10N. W. 20th Avenue, Portland, Ore., currently controls the property under,a nominal leasing agreement. J. W. McDaniel, 44 Lake Place, Bend, Ore., has done much of the underground and surface exploration on the property.The Glass Buttes district is an area of low relief in the Deschutes River drainage system near the northeast corner of Lake County, Ore. (See fig. 1.) The arid climate is marked by extremes of winter and summer temperature. Water for cane use is not available in the immediate area. Well water, however, can be obtained in limited supply on ranch property 5 miles to the south."

Aug 1, 1946

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

By R. H. Nielsen

A new, cheaper precipitation scheme has been developed to produce purified zirconium oxide, Technical-grade sulfuric acid is used to precipitate a basic zirconium sulfate from a hot dilute hydrochloric acid solution. With close control of temperature, pH, and zirconium - sulfate ratio, excellent purification and complete zirconium recovery can be attained. The process has been successfully applied for 3 months and has proved to be a more satisfactory procedure than the ammonium phthalate process used previously. INTRODUCTION The Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines has developed and improved the Kroll process for the production of pure ductile zirconium and hafnium. metal. Since 1946 over 1 million pounds of zirconium sponge metal has been produced, mostly high-purity material for the Atomic Energy Commission

Jan 1, 1956

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971