Search Documents

By W. J. Campbell

This report by the Federal Bureau of Mines Particulate Mineralogy Unit recommends mineralogical definitions and identification-characterization concepts for selected silicate minerals and their asbestiform varieties. Precise definitions acceptable to mineral analysts, regulatory personnel, and medical scientists are essential because of the present lack of conformity in terminology concerned with measuring and controlling asbestiform particulates and their related health effects. Because of the complexity and variability of crystal morphology in different mineral groups, the descriptive terms are generally explained by illustration rather than by numerical values. Applications and limitations of several analytical techniques for particulate identification and characterization are discussed.

Jan 1, 1977

By A. T. Iannacchione

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. 'Wants' in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,954 samples, representing the products of 93 companies. The samples were collected during December 1955, January and February 1956. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the post 10 years is given on page 5.

Jan 1, 1956

By L. T. Grose

The Bureau of Mines conducted a comprehensive study of the Kanab, Kolob, Kaiparowits, and Harmony coalfields of southwestern Utah to obtain additional information and to determine the potentials of these coalfields as sources of energy for steam-electric power-generating plants. Field examinations were made to ascertain the geologic structure and the stratigraphy of the coalfields, the accessibility of the coal-bearing strata, and the general nature of the coal-bearing strata and the terrain. Many mines, both active and abandoned, were examined, and key personnel in the coal industry in the area were consulted. Available analyses of southwestern Utah coals were compiled, and tentative conclusions regarding the rank and quality of the coals were drawn. Coals have been classified by rank according to the standards established by the American Society for Testing and Materials in 1964. The Parr formula for moist, mineral-matter-free British thermal units has been used to calculate the rank of each sample, except as otherwise noted. Water resources related to the areas of the coal reserves also were investigated. Existing literature and maps pertaining to the geology of the areas were reviewed. Production potentials of the coalfields and economic conditions affecting the possible utilization of the coal reserves as sources of energy for steam-powered electricity-generating plants were investigated and analyzed. The data obtained and the conclusions reached as a result of this study are included in this document. The total reserves of subbituminous A and high-volatile bituminous C coals in the fields of southwestern Utah are estimated to be at least 8 billion short tons at depths generally less than 2,000 feet. It appears likely that this estimate will be increased as additional data are made available through exploration and other investigations. Sufficient coal is available in four southwestern Utah counties to supply three or four large steam-electric plants. If the States involved grant water rights to companies planning to build steam-electric plants, the cost of producing power with coal might be attractive and might justify the construction of one or more of these plants.

Jan 1, 1967

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929

By J. K. Whyatt

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mine in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters-cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 2010

By Raymond B. Ladoo

Cne of t·: . .:: i::,portt recent developrr.ents in the feldspar industcy l:.a.s beer. tl:.e r,:ipid. rise of Ne·N H.v-:psr.ire as a. feldspar producing State. Tl:.e unusual size and purity of t: e deposit now 'being worked ne3.r Keene, and tr.a i.nproved metl:.ods ot:' rr.ining srd ir,illing used l:.ave been responsible foe tt.is situation. ti'eldsp'.:l. w'ls occ':tsiona.lly produced sorr.e ye1rs ago in srr.a.ll (tuantities in New Hrunpshi :e, but t::.e State had not been considered a producer of" feldspar ui til lS3l. In the s::ring of tr .. at yea!', t:.e '[eane iic Products co. of Keene, N.H., beg3Il in a srr.9.ll way tl:e production of feldspar fro:n t1eir property in Gilsum, H.H., whicr. l-.a.d long been opera.tei a.s a :tl.ca mine. The purity of the feldspar at enoe '\ttracted f''.lvorai)le attention. and tt.e production of crude ore rapidly in­ cre'.\sed. Early in 1922, a new company, t'he Golding-Keene Co,

Sep 1, 1922

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By E. Chin

The production of crude mineral commodities in Bangladesh was limited to natural gas, a small amount of construction materials, and clay for ceramics and bricks. No metallic minerals were mined. The only mineral commodity of economic significance was natural gas. Natural gas production has 'been climbing steadily and becoming an increasingly important source of energy for the country. Proved gas reserves were over 4.5 trillion cubic feet, but the amount has been increasing as exploration discovers large new deposits. Some sources quote reserves at over 10 trillion cubic feet.

Jan 1, 1984

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By J. P. Powell

Records show that systematic water flooding was begun as early as 1935 in Greenwood County and in 1937 in Butler County. Water flooding on some earlier projects in Greenwood County were described in a Bureau of Mines Report of Investigation.2/ This report presents a discussion of 4 projects -2 in Butler County, 1 in Greenwood County, and 1 in Butler and Greenwood Counties. The location of these projects is shown in figure 1. The projects have been in operation 6 to 12 years and have recovered about 6.6 million barrels of additional oil from the injection of 84.7 million barrels of water. Three of the projects take advantage of the elevation of the nearby hilly terrain, and water from the treating ponds flows by gravity through the filters into the clear-water tanks. By utilizing gravity flow, fewer pumps and less electrical energy is required, resulting in more economical operation.

Jan 1, 1956

By Jerry G. Craig

The Bureau of Mines has developed a computerized oil and gas well data retrieval system from studies of the waterflood potential of a producing reservoir. This system stores pertinent information about each well completed in a reservoir and facilitates selection and manipulation of large volumes of data. Use of the system enables reservoir information to be supplied rapidly, accurately, and at less expense.

Jan 1, 1971

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932

To perform comprehensive economic evaluations on both existing and proposed mineral operations. Approach A comprehensive computer model was developed which is capable of evaluating the economics of an entire mineral recovery operation, including exploration, acquisition, infrastructure, mining, milling, smelting, refining, transportation, taxation, and return of and on capital. How it Works The MINSIM (MINe SIMulator) economic evaluation concept was developed by the Bureau of Mines in 1967. The initial versions used a continuous discounted cash flow rate-of-return (DCFROR) to measure the effect of changes in expected revenues and costs. Subsequent enhancements to the program have expanded and strengthened MINSIM, especially the addition of an option which determines total production cost (i.e., the commodity selling price that a mineral recovery operation would require in order to obtain a target rate of return), an expanded capacity for evaluating by-products from a mineral property, and significantly broadened taxation determining capabilities. The MINSIM computer program uses essentially the same procedures and calculations that are performed in a manual economic evaluation, although the program accomplishes its tasks much more rapidly and accurately, An experienced mineral economist may require a week to evaluate a single mining operation with the same detail and consistency provided by MINSIM in a matter of seconds of computer time.

Jan 1, 1983

By T. F. Anstett

The Bureau of Mines estimated the potential availability of rare-earth oxides (EtEO), including yttrium, and thorium, which is also contained in the rare-earth bearing minerals monazite and bastnasite, from 38 'properties in market economy countries (MEC's). Only nine of the properties evaluated produce or would produce REO as the primary product; the others contain REO as a byproduct, chiefly from mineral sands operations recovering rutile, ilmenite, and zircon. Nearly 77% (2,578,000 mt) of the total 3,355,000 mt of recoverable RE0 evaluated is from producing properties. It is estimated that 21% (705,000 mt) of this total is from properties that could not realize a positive rate of return at the January 1984 market prices for the recovered commodities. At production capacities assumed for this evaluation, the amount of RE0 potentially available from producers ranges from an estimated 46,500 mt in 1986, to a peak of 50,900 mt in 1992, to 49,900 mt by the year 2000. Total MEG production in 1984 was estimated at 40,700 mt. Assuming demand does not increase sharply, producing properties can continue to fulfill overall REO demand through at least the end of this century.

Jan 1, 1986

By N. S. Dalal, Xianglin Shi

"Electron spin resonance (ESR) spin trapping experiments have been carried out to investigate the mechanism of sulfite oxidation em¬ploying 5,5-dimethyl-l-pyrroline-1-oxide (DMPO) as a spin trap. The results show that sulfite autoxidation, catalyzed by Mn(II), involves not only the SO-3 radicals but also the •OH radicals. An addition of H2 02 to the sulfite aqueous medium significantly increases the •OH radical formation. This result provides new clues to the chemical mechanism of the sulfite oxidation and the sulfite toxicity.INTRODUCTIONStudies of the oxidation of the sulfite (SO 2-/3) ions under various conditions are of high current interest because excessive exposure to sulfite is toxic and the origin of this toxicity seems to involve sulfite oxidative pathways [1]. An important fact is that human exposure to sulfite is on the increase [1,2]. Some of the increase in the sulfite exposure is linked to the fact that SO2 is a major air pollutant [2] and in aqueous media SO2 exists in equilibrium with SO2-/3. In addition, beverages and foods are common sources of sulfite intake. For example, sulfite is used extensively in the wine industry as an inhibitor of yeasts and bacteria and is present in finished wines in concentrations up to 6 mM [1]. Sulfite is also often added to dehydrated fruits, vegetables and soups, as well as fruit juices and beer [1,3,4]. Because of these, the mean daily intake of sulfite from diet (in the United States) has been estimated to be between 0.0014 and 0.14 mM/kg body weight [1]. At such high levels, sulfite exposure can have toxic effects, such as the induction of an acute asthmatic state [5,6]. Sulfite also appears to have adverse genetic effects [7] and can act as a mutagen or comutagen [8] and a cocarcinogen [5,7-9]."

Jan 1, 1990

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By S. C. Termes

To help develop the basis for new fine-particle separation methods, the Bureau of Mines has investigated the use of cross-linked starches containing four chelating groups--carboxylate, iminodiacetate, dietha-nolamine, and xanthate--as flocculants for selected metal oxide and hydroxide mineral fines. It was found that those starches capable of interacting with the mineral surface by a chemisorpti,on mechanism (as indicated by zeta potential measurements) produced the highest recover-ies and'grades of the metal oxide or hydroxide when flocculated from a binary mixture with quartz. The effects of pH, dispersing agent, stirring rate, stirring time, and starch dosage on selective flocculation were studied for binary mixtures of hematite and chromite with quartz. Floc strength becomes important in achieving maximum recoveries by mechanical postflocculation separations.

Jan 1, 1985