Search Documents

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

By B. W. Gandrud, G. T. Bator

The recent introduction of small coal jigs in Alabama to meet the needs of truck - mine operators for cheap and economical cleaning equipment marks another step in Alabama's pioneering record in the mechanical cleaning and preparation of coal . During the past 4 or 5 years a number of these small jigs , with capacity of 5 to 10 tons per hour , have been installed at Alabama truck mines and at a few truck mines in Illinois , Tennessee , and Pennsylvania . Most of the installations have been at mines that specialize in the production of domestic , stoker coal . This report describes three models of small jigs and includes performance data obtained recently on one of the models by the Bureau of Mines, United States Department of the Interior , in cooperation with the University of Alabama, Tuscaloosa , Ala . , for the purpose of comparing it with fullsize jigs on a performance basis . With literally hundreds of truck mines now in operation throughout the country , it has been assumed in preparing this report that there is widespread interest in the availability of small - scale inexpensive preparation equipment for use at such mines in the production of steam and domestic coal and in some instances coal for manufacture of coke . Practically none of the coal from Alabama truck mines is scld to coke - oven plants ; but in some sections of the country truck mines supply a considerable amount of coking coal, and the use of small, inexpensive washers at some of them might be very advantageous during the present war emergency from the standpoint of increasing pig - iron production through improvements in coke quality .

Aug 1, 1943

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By O. Terichow

A pendulum sclerometer designed by the Bureau of Mines is described. Its method of operation is given, along with the results of tests made on representative mineral samples of Mohs' hardness scale to determine the applicability of the device for research on rock testing. The sclerometer hardness values obtained from the tests indicated that reproducibility and accuracy were good. A quantitative comparison of the pendulum hardness values with microhardness and surface energy values published by other investigators showed good agreement on minerals with Mohs' hardness numbers of 2 to 9.

Jan 1, 1967

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By J. B. Janus

In connection with the purchase of coal under specifications for Government use, the Bureau of Mines in this report has compiled data on 81 mines located in 15 States. This annual report lists analytical data on the composition and quality of tipple and delivered samples of coal collected during fiscal year 1973. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for most of the coalbeds listed. The deliveries were sampled at destination in accordance with instructions issued by the Bureau of Mines. All samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By Charles Prasky

The objective of this investigation by the Bureau of Mines was to determine the response to sulfatization of diverse low-grade manganiferous materials in the iron formation of the Cuyuna district. In line with this objective a bench-scale sulfatizing procedure was developed that was less expensive and more rapid than pilot-plant methods. Samples from the central and south- western parts of the North range were tested. Results of evaluating a total of 46 pelletized samples, originating in areas with an estimated potential resource of 94 million long tons with a manganese content of 7 percent, indicates that approximately 87 percent of the manganese may be recovered as a synthetic manganese ore. This is equivalent to more than 12 million long tons of a metallurgical-grade ore, containing 46 percent manganese. It is anticipated that a premium product, containing over 50 percent manganese, may be obtained by sulfatizing procedures. This report is part of a continuing investigation5 6 of Cuyuna iron range manganese deposits in Crow Wing County, Minn. Lewis and coworkers describe the manganiferous iron formation in the bedrock of the Cuyuna district and include a description of a high-temperature differential sulfatizing process for recovering a ferrograde manganese product. The low-grade manganiferous

Jan 1, 1961

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

By M. P. Ahola

This U.S. Bureau of Mines report presents an overview of the use of three unique numerical modeling methods to analyze cutter roof problems in underground coal mines. Cutter roof failures are common in coal mines where the immediate roof is comprised of thin laminae exposed to highly biaxial tectonic stress fields. The predominant mechanism for failure is assumed to be excessive shear stress at the entry corners exceeding the shear strength of the rock. Early work in this area utilized the finite-element method and then the boundary-element method to analyze several cutter roof control measures. Various stress control measures were simulated to estimate their respective effects on reducing the high levels of shear stress at the entry corners. More recent studies made use of the discrete-element method. This method was used to take the analyses beyond the elastic continuum limits to simulate the propagation of a shear fracture and subsequent redistribution of stress within the mine roof. A simple roof bolt model was implemented to show the benefits of bolting to increase the resistance to shearing and separation along horizontal bedding planes and maintain roof stability.

Jan 1, 1991

By Glenn E. Johnson

The Bureau of Mines investigated the production of hydrogen cyanide by reacting powdered coal (minus 300 mesh) with ammonia at 1,250° C in a bench-scale study. Both metallic and ceramic reactors were used. Yields up to 0.7 cu ft of hydrogen cyanide per cubic foot of ammonia consumed r- obtained. The resulting ammonia conversion of about 75 volume-percent approximates conversion obtained commercially in processes utilizing natural gas and platinum catalysts. The coals that had higher volatile-matter contents gave the best yields of hydrogen cyanide. Allowing the coal to adsorb ammonia before reaction resulted in increased yields of hydrogen cyanide. Cost studies for a plant with a 40-million-pound-per-year capacity indi-cate that hydrogen cyanide can be profitably coproduced with carbon black, from coal and ammonia, at the current market price of hydrogen cyanide (11.5 cents/lb). These figures are based on heating the reactor electrically. If a cheaper heating method were devised the economics of the process would be more favorable.

Jan 1, 1967

By L. B. Pankratz

High-temperature heat-content values of pure lutetium sesquioxide and dysprosium sesquioxide were measured over the temperature range from 298° to 1,800° K. Similar data for cerium sesquioxide were calculated from measurements of a mixture of cerium sesquioxide and dioxide and known values for cerium dioxide. The results for lutetium sesquioxide are regular. Dysprosium sesquioxide has a minor thermal anomaly near 1,590° K, the extra heat absorption being 220 cal/mole, Hexagonal cerium sesquioxide undergoes a transformation around 1,050° K, which is only slowly reversible; consequently results were obtained for both the low- and high-temperature varieties. The original heat-content data are reported, and smooth values of heat content and the corresponding entropy increments are tabulated. Equations were derived to represent the heat-content values.

Jan 1, 1963

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By B. D. Nash

The Bureau of Mines continued its research into the recovery of fluorine by the phosphoric acid acidulation defluorination of phosphate rock concentrates. A small process development unit with a capacity of about 10 kilo-grams of charge per hour was operated, and concentrates from both Idaho and Florida were processed. Over 80 percent of the fluorine was evolved and recovered as a dilute fluosilicic acid solution. Phosphate extraction from the concentrates always exceeded 98 percent. The fluorine was converted to a synthetic fluorspar product (3CaFa?SiOa) suitable for use as a slag conditioner in electric furnace steelmaking operations.

Jan 1, 1977

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989