Search Documents

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968

By J. W. Griflith, P. A. Mack, C. M. Lang, S. Riling

"N-acetyl-beta(B)-D-glucosaminidase is a N-acetyl-beta((B)-D-glucosaminidase enzyme se¬creted by alveolar macrophages in response to phagocytosis of particulate material. Alveolar macrophages participate in the degradation and fibrosis of pulmonary tissue that results in pneumoconiosis. Known quantities of four characterized respirable dusts were bronchoscopically placed into the right caudal lung lobe of macaque monkeys. Bronchoalveolar lavage (BAL) samples were collected from dust-exposed right lung and unexposed left lung of the same individuals at 2-week intervals for 12 weeks after dust instillation. The samples were tested for N-acetyl-B-D-glucosaminidase activity to determine if the enzyme levels could serve as an indicator of pulmonary injury induced by generic coal dusts when compared to known fibrogenic and nuisance dusts. Installation of generic quartz, anthracite, or TiO2 dusts produced significant elevations of enzyme activity and increased numbers of macrophages in the dust-exposed lobes. Elevations in enzymatic activity and macrophage numbers were greatest in response to generic quartz dust. These results suggest that quantitative levels of N-acetyl-B-D-glucosaminidase activity may be a useful indicator of acute and chronic lung injury following exposure to fibrogenic and nonfibrogenic dusts.IntroductionCoal workers pneumoconiosis (CWP) is an occupational pulmonary disease associated with the inhalation of coal mine dust. An important external factor in the development of CWP is the composition of the respirable coal mine dust. A cause-and-effect relationship exists between coal mine dust and CWP, but it has not been shown that exposure to generic coal dusts will cause CWP [12]. Numerous immunological, biochemical, and cellular changes occur in CWP; however, in this study, only N-acetyl-beta(B)-D-glucosaminidase (NAGase), protein, and alveolar macrophages (AM) will be examined [7, 32, 33]."

Dec 1, 1996

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By C. G. Storm

Permissible explosives are those that have passed the tests pre- scribed by the Bureau of Mines for explosives intended for use in coal mines, and are therefore recommended by the bureau as suitable for this class of work when used under the prescribed conditions. The tests for permissible explosives and the conditions prescribed for their use are described in Miners' Circular 6 of the Bureau of Mines. Up to June 1, 1915, 168 explosives had been classed as per- missible explosives; 133 of them were then on the bureau's "per- missible list" and 35 had been withdrawn by the manufacturers. In addition to the required physical tests, each explosive is sub- jected to a complete chemical examination in order that its exact composition may be known and also that the composition of future samples of the same explosive collected in the field may be compared with that of the sample which originally passed the bureau's tests, for by such comparison it may be possible to ascertain whether or not the explosive as supplied to the miner is still "permissible." This bulletin is published primarily for the purpose of informing manufacturers of such explosives as to the methods used by the Bureau of Mines in the analysis of samples received for tests to determine their permissibility. Such information may be of value in cases of possible controversy over the results obtained in the analysis of a field sample as compared with those obtained in ana- lyzing the sample originally tested by the bureau. Also, a descrip- tion of the methods used by the Bureau of Mines in the analysis of explosives should be of assistance to the many chemists engaged in similar analytical work.

Jan 1, 1916

By J. Alton Burks

When acoustical materials are used in a mining environment for noise control purposes, they are subject to environmental deterioration from hydraulic fluid, moisture, and dust. These and other factors can cause physical degradation of the material, which can lessen its ability to absorb sound. In this study, the Bureau of Mines measured the sound absorption properties of 16 different acoustical materials after 4 sample treatments: (1) being kept clean and dry (as received from the supplier), as a control or reference standard, (2) immersion in water and draining, (3) immersion in lOO-pct-petroleum-type hydraulic fluid and draining, and (4) exposure in a coal mine. The last three treatments were used to approximate the type of physical degradation that can be experienced in actual use. The impedance tube or standing wave method was used to measure the normal absorption coefficient. It was found that the absorption coefficient of most materials was adversely affected by the retention of either oil or water, with oil having the greater effect. The only class of materials that was affected by neither oil nor water was neoprene foam.

Jan 1, 1990

By Richard L. Fischer

Constant-volume charges of precipitated PETN (pentaeythrite tetranitrate) at three specific gravities (0.50, 1.00, and 1.50) were used in laboratory tests to examine the effects of changes in explosive properties on free-surface displacement pulses and on crater dimensions. The tests were performed in large blocks of cement-mortar. The values for the detonation velocity, detonation pressure, specific energy, energy density, and energy release rate were calculated from the explosive loading density. Calculated explosive properties were correlated with free-surface displacement pulse measurements, strain energy, and measured crater dimensions. Increases in explosive properties resulted in increased free-surface displacement pulse parameters and crater dimensions. The loading density, detonation velocity, energy density, detonation pressure, and energy release rate were found to be best indicators of explosive performance. Simple acoustic relationships involving impedance ratios were examined and could not be used to predict peak displacement amplitude or strain energy. Data are presented in the customary English units as well as the International System of Units (SI).

Jan 1, 1970

By E. D. Gardner

Humphreys Gold Corporation of Denver, Colo., was conducting a successful placer operation in 1936 on North Clear Creek about 6 miles below Blackhawk in Gilpin County, Colo. About 3,000 cubic yards of gold-bearing gravel are dug daily (September. 1936) by two draglines and a power shovel. The gravel is screened in a portable washing plant; the trommel oversize is discarded, and the undersize is pumped to a gold-saving plant. The gold is caught in riffles in sluice boxes. The total cost of mining is about 20 cents per cubic yard. The mine is in a narrow canyon at an altitude of 7,200 feet. The Blackhawk-Central City branch of the Colorado & Southern RR. runs over the property. Freight platforms for receiving supplies were moved as the workings advanced. The workmen reached the mine on a speeder that ran on the railroad tracks from a point on the automobile highway (U. S. 40) on Clear Creek near the bottom of Floyd Hill, about 5 miles distant. The mine is 36 miles by road and speeder, or 30 miles by rail, from Denver.

Jan 1, 1937

By Thomas J. Peters

The King Mountain study area is centered about 120 air km northwest of Blackfoot, and 30 air km north of Arco, Idaho. The study area makes up the southern one-third of the northwest-trending Lost River Range--the highest mountain range in Idaho. The area is predominantly underlain by Paleozoic-age marine limestone and lesser dolostone, with a relatively small inlier of silica-rich, Ordovician-age quartzite. There are vast, unquantified resources of these industrial minerals present; however, special markets need to be developed for these resources which are near enough for transportation costs to be competitive. Five prospects were found in the study area; however, only one, the Elbow quartz silica prospect, contains resources and current claims. There has been no mineral production in the study area.

Jan 1, 1993

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By F. X. McCawley

The Bureau of Mines, in pursuing its goal of extending the life span of strategic materials, conducted field corrosion studies at the East Mesa Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to determine the optimum materials of construction for use in geothermal mineral energy resource recovery plants. These studies included characterization of geothermal environments and in situ corrosion testing. The corrosion resistance of 10 alloys exposed to 5 brine and steam process environments was evaluated using the low-salinity, high-temperature brine from geothermal well Mesa 6-1. Of these alloys, Hastelloy C-276, Hastelloy S, Incone1 625, titanium-2nickel, and 316 L stainless steel had excellent resistance to corrosion in all of the process environments; E-Brite 26-1 and 430 stainless steel had fair resistance. Although general corrosion rates for 4130 steel and 1020 carbon steel were substantially higher than those of the other iron-base alloys, these two alloys could prove useful in low-salinity process environments because of their low cost. Aluminum alloy 5005 was the least corrosion resistant alloy and pitted severely. Scales formed on all of the alloys in every process environment. Calcite, aragonite, and an amorphous silicate were the major components of the scales.

Jan 1, 1980

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau's surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation. The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 2010

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By K. M. Connor, O&apos

Variations in overburden geology must be considered in applying subsidence prediction methodologies developed by the U.S. Bureau of Mines (USBM). To characterize rock mass overlying high-extraction coal mines, the USBM utilizes a computer spreadsheet program and modified Rock Mass Rating (RMR) system. The spreadsheet calculates an RMR based on a bed's engineering properties determined from core logs and laboratory tests. An in situ deformation modulus and a bending stiffness are computed for each bed. Stiffness-versus-depth plots identify groups of beds with similar stiffness. Large variations in stiffness between adjacent beds are considered significant horizontal discontinuities where slip is likely. Time domain reflectometry (TDR) is used to verify this hypothesis by measuring shear displacement along such discontinuities. A model of the overburden is built by assuming that a near-surface laminated beam exists above a transition zone in which large plastic slip occurs along horizontal discontinuities. Increasingly thicker groups of beds are modeled to determine the most probable beam thickness based on a comparison with measured deflection profiles. The inverse of maximum beam deflection is an index parameter known as "bridging potential," a single value that incorporates both overburden geology and mine geometry.

Jan 1, 2010

By R. W. Watson

At the request of the Mine Safety and Health Administration (MSHA) the Bureau of Mines evaluated the potential hazards of three compressed oxygen self-contained self-rescuers (SCSR's) designed for use in under-ground coal mines. The evaluation followed the lines used in a similar investigation of chemical self-rescuers and involved laboratory experiments as well as field trials designed to simulate a mining environment. They included bullet impact, bonfire, feeder-breaker impact and feed-through, and mining machine runover tests. The work showed that the units were not inherently unsafe but that under certain conditions of extreme abuse they can present a potential ignition or explosion hazard. This, coupled with a survey of reported damage on SCSR's currently deployed in underground mines, which indicated a relatively high frequency of incidents leading to the destruc-tion of the units, led to new recommendations on the deployment of SCSR's. The recommendations formulated by MSHA state that the units should be either properly worn by the miner, stored in heavy containers, or otherwise protected from situations in which they might be accidentally ruptured or destroyed, such as runover by mobile mining equipment.

Jan 1, 1984

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By R. W. Lowe

1. Reserves are estimated in the Nemo, Sewanee, Wilder, and White Oak beds of Fentress County, Tenn. The Wilder is the only bed being mined commercially and contains the largest known reserves. Eleven lesser known beds are present in the county, but not enough information on them was available for estimating the reserves. 2. Known measured and indicated reserves, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 102 million tons as of January 1, 1955. This total includes 66 million tons in beds 28 inches and more thick.

Jan 1, 1956

By John C. Machisak

Statistical data on injuries in the metal and nonmetal industry of the United States first became available to the Bureau of Mines by collecting reports from the operators for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1954, is the 31st publication (1933-34 was published as Bulletin 398) containing statistical data on injuries at metal and nonmetal mines and related plants, and it 1s the first such bulletin to be published since 1942. The last publication was Bulletin 461, Metal and Nonmetal-Mine Accidents in the United States, 1942. The unpublished statistics for 1943-53 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries and related employment at metal and nonmetal mines, but there is no Federal law that compels operators to submit such information. Therefore, all materials submitted are voluntary responses to the Bureau's requests for information. The figures presented herein may not be complete for the entire industry, nevertheless, every effort has been made to make them so, and the data given are believed to be representative of the hazards to which metal and nonmetal workers are exposed. Moreover, the figures are comparable as between States-which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1957