Search Documents

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is improved.

Jan 1, 1980

By Cloyd M. Smith

Progressive mine management is placing increased emphasis on improved ventilation as a contribution to better safety , health , and productivity of miners . Management is on the alert for means of bettering the working environment by increasing the flow of air and distributing it more effectively to the working places , having in mind the necessity of avoiding exorbitant ventilation costs . A basic need in planning betterments of this kind is knowledge of existing rates of flow and air pressures , infCoorrmmaattiicon that is supplied through ventilation surveys . Some companies make partial surveys from time to time , but few make complete surveys on a routine basis . This report describes the practice of a large British anthracite -mining company , which operates 24 collieries in South Wales , in carrying out a routine program of ventilation surveying . Ventilation characteristics and climatic conditions in the working places of its collieries are determined at frequent intervals with a view to increasing the effectiveness of ventilation and protecting the health of workers . It is thought that many of the points of the procedure used in making the surveys and in compiling and reporting the results will be applicable to American practice and that a discussion of the program may be helpful to colliery managers who are planning similar work .

Oct 1, 1949

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By Raymond W. Hiteshue, Sam Friedman, Paul Dobransky, Robert Madden

A hvab coal was carbonized in a closed system at 600 ° C and 40 to 1 , 200 psig to produce a high- Btu gas and char . By retaining the volatiles within the system, it was possible to virtually eliminate production of tars and oils . Depending on pressure and residence time , yields of combustible gases (72 to 92 percent methane ) amounted to 4,000 to 6,000 cubic feet per ton of maf coal and gross heating values of these gases varied from 830 to 960 Btu per cubic foot . Yields of char (maf ) were about 1,600 pounds per ton of maf coal . Increased residence time favored production of gases but reduced their heating values , whereas increase in pressure resulted in somewhat higher heating values and lower production . Similar effects were observed from the carbonization of a low- temperature tar . If these results could be translated to an economical carbonization process for producing high- Btu gas from coal , the demand for coal could be expanded by 40 to 50 million tons per year . Because of large yields of char , a process of this type would obviously have to be integrated with coal - fired power plants . Fortunately , operations could be conducted at essentially atmospheric pressure as product gas under this condition can be obtained in satisfactory yields and with good quality .

Jan 1, 1964

By R. V. Lundquist

This report describes results of tests on the desilication of solutions resulting from the leaching of lime-soda sinters. Desilication was accomplished by heating the solutions in an autoclave. A liquor relatively free of silica was obtained after 30 minutes of heating at 200 p.s.i.g. in the presence of lime. The addition of lime improved desilication, but the rate and efficiency of desilication was effected by the quality of lime used. The optimum quantity of lime for effective desilication was about 6 grams per liter. A lesser quantity gave poorer desilication, and a greater quantity increased the alumina loss without improving desilication. The alumina loss was approximately proportional to the lime added. A complex structure, called artificial noselite in this report, was the only silica bearing compound detected in the desilication precipitate. Other compounds present were Ca(OH)2 (calcium hydroxide), CaCO3 (calcium carbonate), and Ca [A1(OH)6]2 (hydrated tricalcium aluminate). Sodium carbonate in the leach liquor retarded the formation of the calcium aluminate; hence it decreased the alumina lost to the precipitate. The extraction of alumina from aluminum silicate materials by the limestone soda-sinter process has been investigated by the Bureau of Mines for many years. The process consists of the following major operations: Blending the aluminum silicate with limestone and soda ash in such proportions that dicalcium silicate and sodium aluminate are formed on sintering; leaching the sinter in a carbonated caustic solution to extract the soluble alumina; purifying the leach liquor by the precipitation of soluble silica (this precipitate is designated desilication precipitate in this paper); precipitating alumina trihydrate from the purified liquors by carbonating with carbon dioxide gas; and calcining the trihydrate to alumina. Commercial grades of

Jan 1, 1962

By Wm. F. Netzeband

The purpose of this paper is to present to the operators, in other districts a detailed description of the ruining method used and the results obtained to exploiting one of the zinc-lead deposits of the Kansas-Oklahoma-Missouri district. No. 1. mine is located in the heart of the town of Picher in the extreme northeast corner of Oklahoma. HISTORY The first prospect drilling was done at No. 1 mine late in-1914, and shaft sinking was started early in 1915. Sufficient ore was developed to start construction of the mill in April, 1016, Production begin in August, 1916, and the mine s been producing, except for short periods, to the present time. The property was originally a 40-acre tract, but additional properties have been consolidated with the original one until the mine now covers 200 acres.

Jan 1, 1929

By T. A. Hendrickson

The Bohemia district, situated about 30 miles southeast of Cottage Grove, Oreg., in the Calapooia Range, has been the major producer of lead and zinc in Oregon. Sporadic production has been Maintained from the district since its early discovery about 1858. In 1942, a selective-flotation mill was built at the Champien mine, which operated for only a short time and was forced to close because of the war and lack of labor. The Champion mill reportedly has been operated as a custom mill for the treatment of ore from the Musick and Helena mines, located in the district sometime in the past. This report summarizes the results of laboratory ore-dressing studies made on ore samples from the Musick and Helena Mines.

Jan 1, 1951

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By P. A. Wasson

Drill cores from 15 holes in the West Central Mesabi Range were studied as part of the Lake Superior iron resource investigation begun in 1957 by the Bureau of Mines. Chemical, petrographic, and metallurgical analyses were made to determine grade, mineralogy, magnetic characteristics, and response to beneficiation. Data in this report were developed to provide a better under-standing of the nature and character of low-grade iron ore occurrences, to measure potential of usable ore, and to provide a basis for comparison with bank samples previously taken in the same general area. The average iron content of 4,445 feet of core was 31.8 percent. Iron oxides present were hematite, goethite, and magnetite; the gangue minerals were chiefly quartz, iron silicate, and iron-bearing carbonates.

Jan 1, 1962

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By Oliver C. Ralston, Foster Fraas

"INTRODUCTION The predominant characteristic of powdered mica is the thin -plate shape of the particulars, and the thinner the plates, the more enhanced is this characteristic. Consequently, it is frequently desirable to grade mica according to the thickness of the plates. Concerning the various possible methods for grading mica, very little has been published. There is also no information on the relative quantities of mica per given range of plate thickness. This paper presents a graphical method that shows how these quantities are distributed and how the different methods of grading compare.CUMULATIVE BULK DENSITYBulk density, which is an indirect measure of the plate thickness, was determined in a small cylindrical cup of 3.37 cubic centimeters volume. The mica was placed in the cup under a standard procedure. The densities thus measured checked these determined in a 273 cubic centi¬meter cup with less than a 2 percent error.In calculating cumulative densities it is important to know how they are averaged. In any grading operation the bulk density of a series of fractions is determined. Starting with the lowest density fraction, the cumulative percent under-density can be calculated through the various fractions. It is possible that quantity may be measured by volume or weight and that the averaging may be done by a number of methods. However, experimentally it has been shown that the quantity must be by volume and that the averaging must be arithmetic. This is illustrated in table 1, in which the calculated and actual bulk densities are listed."

Sep 1, 1942

By Charles L. Kimbell

Tables 16 through 19 continue the series of providing the world merchant fleet distribution by type of vessel and the ranking of the major fleets by country of registry. Table 20 this year provides a summary of the world's liquid gas carrier fleet. These vessels are included in the totals given for the world's tanker fleet, but gives a breakdown demonstrating the growth of the importance of natural gas in the world's energy commodity consumption. Panama and Suez Canals Tables 21 and 22 provide the latest available information on the transit of mineral commodities through the Panama Canal, by number of vessels, direction, and the commodities transported. Although the number of vessels transiting the Panama Canal dropped slightly (0.5%) between 1989 and 1990, the total amount of cargo moved rose by 3.6% and the amount of mineral commodities moved rose by 7.2%.

Jan 1, 1993

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By G. S. Scott, G. W. Jones, I. Spolan, R. E. Kennedy

In studies made by the United States Bureau of Mines to determine the causes of explosions in medium-pressure acetylene generators , it was shown that when these are operated at elevated temperatures the acetylene liberated in an acetylene generator carries enough water vapor to heat certain types of carbides to a high temperature , when the acetylene- water vapor mixtures are passed through the carbide . This report contains results of further work carried out to develop an apparatus to show the heating effects or reactivity of various types of carbides in contact with acetylene - water vapor mixtures .

Apr 1, 1947

By Jr. Harty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tonnage of our steel by from 60 to 80 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores Which has been made available by the bureau's ore-dressing studies, combined with the products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements when manganese-silicon alloys and ordinary Spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromanganese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores. This paper resents the results of work done under a cooperative agreement between the Pittsburgh Experiment Station of the United States Bureau of Mines and the Carnegie Institute of Technology, the Metallurgical Advisory Board, and the University of Pittsburgh, Pittsburgh, Pa.; between the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.; between the North Central Experiment Station of the United States Bureau of Mines and the University of Minnesota, Minneapolis, Minn.; and between the Rare and Precious Metals Experiment Station of the United States Bureau of Mines and the University of Nevada, Reno, Nev.

Jan 1, 1931

By C. H. Herty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tone of our steel by from 60 to 30 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores which has been made available by the bureau's ore-dressing studies, combined with the ,products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements Then manganese-silicon alloys and ordinary spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromangenese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores.

Jan 1, 1931