Search Documents

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

This Bureau of Mines investigation addressed two primary issues of air velocity measurement in mines: the determination and use of correction factors, and the development of guidelines for the selection of a suitable site at which the measurements should be taken. Other facets of the investigation included a comparison of measurement methods and devices, and aircourse cross-sectional area measurement. The study consisted of theoretical, laboratory, and in-mine investigations. The measurement devices included in the experimental phase were vane anemometer, vortex shedding anemometer, a prototype thermoan-emometer, smoke tube, and oil of wintergreen sprayer. The measurement methods included single-point centerline, timed-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices. The study resulted in guidelines for measurement site selection that are applicable to most inmine situations. It also showed that the use of correction factors is problematic. There are many potential pit-falls and there are cogent arguments against using certain correction factors. However, generalized correction factors were developed that can be successfully applied in routine ventilation work, provided that their use is properly understood.

Jan 1, 1985

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended' as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945

By T. J. Ballard

The Tallapoosa Copper mine in Haralson County, Ga., has been operated, or under development at various times since before the Civil War. The geology of the deposit is similar to that of many of the pyrite deposits occurring in the belt of ancient crystalline and metamorphic rocks that extends diagonally northeast-southwest across the State. The Bureau of Mines, in its program of investigation of, strategic mineral deposits, diamond-drilled four holes totaling 1,570.3 feet at the deposit during the period June to September 1947 to verify the old drill records and the continuation of the deposit at depth.

Jan 1, 1948

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By R. T. Johansen

A gradual decrease in injection rates commonly occurs as a water-flooding project becomes older. This decrease can be attributed to changes in reservoir conditions, such as swelling of clay minerals, fillup, or gradual plugging of the sand face. However, a rapid decrease in the rate of injection indicates abnormal behavior and is cause for alarm. Extreme plugging conditions can completely stop injections into a formation. Such behavior in wells was the main concern of the tests described in this report. An accepted method of alleviating this condition is by backflowing input wells - closing the supply lines to the wells and allowing the reservoir pressure to force water back into the wellbore and to the surface. If backflowing is not successful, a string of smaller diameter pipe sometimes is run inside the casing, and the sand face is flushed with a waterspray. More drastic treatment is to inject acid into the wellbore to dissolve extraneous matter, or even part of the reservoir material, in an attempt to restore the permeability of the sand immediately around the wellbore. Any of these procedures can he coordinated with bailing and swabbing of the well for cleanout purposes.

Jan 1, 1957

By T. A. Sullivan

The Bureau of Mines investigated modified sulfur concretes as one part of a program for utilizing sulfur in construction materials. The use of modified sulfur was studied as a means of preventing the stressing action in the concretes caused by the allotropic transformation of sulfur on solidification. Unmodified sulfur concretes have been prepared that have compression, flexural, and tensile strengths equivalent or better than Portland concretes. However, most of these concretes have been vulnerable to deterioration by weathering, temperature fluctuations, and freeze-thaw cycling. The sulfur was modified by reaction with dicyclopentadiene or dipentene before use as an aggregate binder. Sulfur concretes and modified sulfur concretes were pre-pared from acidic and basic type aggregates. Physical properties of the optimum mixtures were determined and compared with each other and with Portland cement concretes. The best results were obtained by reacting sulfur with 5 pct dicyclopentadiene to prepare modified sulfur concretes. Field testing of the concretes are in progress. Present results show that modified sulfur concretes are superior to unmodified sulfur concretes and equal or better than Portland concretes in compressive, flexural, and tensile strengths. Long-term aging characteristics of both modified and unmodified sulfur concretes are being determined.

Jan 1, 1976

By Robert H. Merrill

This report summarizes the first phase of studies to determine the design and behavior of an unsupported roof in an experimental room in limestone. The selection of a roof horizon and the design of the room were results of an investigation of the geology of the formation, the physical properties of samples from the proposed roof, and calculations from the theory of gravity-loaded beams. The design of the opening, some physical properties of the roof in place, and the behavior of the roof were checked by tests in a full-scale experimental room. The room was instrumented to measure roof deflection, separations in the roof strata, and incipient failure. The dimensions of the room before instrumentation was installed were 10 by 100 feet; the room was widened in successive increments to 40 by 100 feet. Between widening operations periods up to 6 months were allowed to provide a time test of the roof spans. The results of the measurements of deflection and separations showed that the lowest 6-inch layer in the roof became detached as the room was widened. This layer was eventually removed after standing without failure for about 4 months at room dimensions of 40 by 100 feet.

Jan 1, 1957

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By T. E. Hill

The Bureau of Mines investigated the possibility of physically separating Missouri and Minnesota granites into commercially usable fractions of feldspar, quartz, and mica by mineral dressing techniques. The probability of r covering a feldspar fraction from raw granite suitable for commercial uses was developed through correlation of the iron oxide content by extensive petrographic studies. This probability evaluation also included Wisconsin granites and a high-feldspar iron ore concentration tailing from Missouri. Laboratory recoveries of feldspar and quartz were on the order of 80 percent. Mineral content of each fraction was generally over 95 percent, indicating excellent response to separatory techniques, Acid leaching of feldspar and quartz concentrates to remove iron oxide improved the grades chemically; however, occluded iron oxide particles in the leached products prevented attaining top grades of feldspar. Mica was removed as scrap grade at low recoveries. Each concentrate conformed to some category of commercial feldspar, quartz, or mica.

Jan 1, 1969

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By A. R. T. Denues

This investigation was made under a cooperative agreement between the United States Department of the Interior, Bureau of Mines, and the Pittsburgh Testing Laboratory. Funds were supplied by the Chile Exploration Co., whose executive offices are in New York City. The support, cooperation, and services of these agencies made the work possible and are acknowledged gratefully. The writer wishes to express his particular indebtedness to the staff of the Explosives Division of the Bureau of Mines for services and assistance, particularly Dr. Wilbert J. Huff, consulting explosives chemist, J. C. Holtz, J. E. Tiffany, and A. B. Coates; to F. O. Gardner, treasurer of the Pittsburgh Testing Laboratory; to G. B. Holderer, consulting engineer in connection with liquid-oxygen explosives for the Chile Exploration Co.; to the Enos Coal Mining Co. of Oakland City, Ind., particularly to G. H. Utterback of the staff of the mine for providing facilities that made field tests possible; and to full-time assistants J. W. Rothhaar and J. G. P. Weinheimer and to W. S. Hiller, part-time assistant, who were employed under the cooperative agreement.

Jan 1, 1940

By G. A. Appell

"INTRODUCTION During the summer of 1945, the Bureau of Mines conducted an investigation and program of churn drilling near the village of Tennyson in Grant County, Wis. The work was undertaken as part of a general investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the war program.The area for special investigation was selected on the basis of favorable structural disclosures, evidence of widespread zinc mineralization, absence of any great amount of exploration to depth beneath the productive shallow workings, and the favorable results of several churn-drill holes in the village of Tennyson.During the Bureau's investigation, 30 churn-drill holes aggregating5,888 feet were completed.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to-the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual. Investigative work, and prepares the final report.The work described herein was accomplished under the direct supervision of Francis C. Lincoln and the author, mining engineers of the Bureau of Mines. Final data on the investigation were prepared under the direction of Edward F. Fitzhugh, Jr., chief Minneapolis Division, Mining Branch."

Jun 1, 1947

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983

By John W. Thatcher

A demountable X-ray tube vacuum spectrograph was designed by the Bureau of Mines for the determination of long-wavelength X-ray spectra from the light elements. This instrument was operated for both secondary and combined primary-secondary excitation of the aluminum K-series. There was an increased analytical sensitivity for elements in period 3, and an indication that with improved X-ray tubes or direct election excitation of the sample, X-ray determination of elements in period 2 is also possible.

Jan 1, 1965

By B. M. Harra, O&apos

Zinc smelting is frequently termed a backward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, low-unit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pounds of ore. The diameter of the retort is limited by the time required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, or producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser attached to one end of the retort, where it condenses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls and of the ore charge itself, the heat efficiency even of the most modern regenerative furnaces is only about 12 per cent. The retorts have a short life, 30 to 60 days, at the high temperature required; zinc

Jan 1, 1923

By T. J. Ballard

"The Hog Creek mine, in lot 92 of the 17th district in Towns County, Georgia, was examined in 1890 by F. P. King, who reported the existence there of a 4-foot vein of corundum. The mine is about 2 miles west of Hiawassee, on the southern side of Ramey Mountain. Ed Burch, of Hog Creek, holds the surface rights, and the mineral rights appear to be vested in the heirs of William R. McConnell, who formerly owned and prospected the property.Examination by the Bureau of Mines showed the workings to be caved, but it was thought advisable to open the mine and uncover the reported vein. The Bureau's work consisted, of trenching and cleaning out the pits and shaft.William R. McConnell, the former owner, prospected the property in about 1890. At some tine during that operation, the prospect was visited by Francis P. Kings a geologist with the Georgia Geological Survey.3/King reported that a 4-foot vein of corundum was exposed g feet below the surface in the main cut and was opened for 20 feet along the strike. He also reported that the so-called ""Georgia rubies"" were taken from this mine.The main mine is about 2,000 feet- north of Hoc Creek on a timbered southern slope of Ramey Mountain. It lies at an altitude of about 2,100 feet, approximately 100 feet above the high-water level of the Catuga reservoir, which floods Hog Creek to a quarter of a mile above its confluence with the Hiawassee River. The nearest water is a small branch about 1,000 feet to the west.Chlorite schist is the principal host rock. It has been intruded by irregular masses of a very herd periodtite rock possibly troctolite. The schist near the surface is extremely weathered, presenting white and red laminations parallel to the schistosity. At a depth of 40 feet in the cross-cut it appears as a fine-grained green-chlorite schist. The schist strikes about N. 350 E. and dips 800 to the southeast.No corundum vein was found, and if any existed it must have been mined out after King's visit. In the pit, about 15 feet west of the shaft, approximately 150 pounds of zoisite and an occasiona1 small crystal of corundum were found imbedded in schist about 18 feet below the surface, near hard, dense troctolite."

Mar 1, 1946