Search Documents

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

By N. L. Kozlinsky, B. W. Gandrud

"The Marvel mines 1 and 3 of the Roden Coal Co. are located in the Cahaba field in Bibb County, Ala., nearly southwest from Birmingham, an airline distance of roughly 30 miles. The coal of the Clark seam at this point has some coking properties, but at present it is sold exclusively as a domestic and steaming coal.This paper, which is the second of a series on the washability of Alabama coals, like its predecessor dealing with the Mary Lee seam,5 contains screen-sizing and float-and-sink tests of a representative sample of the raw slack, and slotted-screen tests showing the proportions of flaky particles in certain selected sizes; inasmuch as this coal is not used for coke manufacture, no crushing tests have been made. These data have been obtained in connection with an exhaustive study of coal preparation in Alabama, now being conducted by the United States Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses, other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods.The only published investigative work on the Clark seam is that of Forbes,6 who gives a number of sections of this seam in Marvel No. 3 mine with proximate and ultimate analyses of face samples taken in the mine and also some analyses of delivered coal.The available information on this coal indicated that the preparation problem was one of ash reduction. In order to substantiate this information a complete analysis of the 3/4 by 3/16 inch size, and sulphur determinations and ash-fusibility tests of the float-and-sink fractions have been made; these results are given in Tables 1 and 2. As these results also indicate that the preparation problem is one of ash reduction, the tests and discussion have been devoted to that subject."

Jun 1, 1930

By O. M. Bishop

"SUMMARYAs a result of the increased demand for fluorspar during the war, the Bureau of Mines investigated numerous fluorspar properties in the southern Illinois field, which is centered in Rosiclare. Among these the J. J. Shelby 40-acre tract on the western edge of the district presented favorable factors that caused it to be chosen /or exploration.H. G. Spiller, formen lessee of the property, had explored the Shelby vein by means of an adit level and winze, and showed it to contain goad values in zinc and fluorspar at the depth explored. A diamond-drill hole with which Spiller explored the vein 78 feet southwest of the winze, however, failed to cut ore. After studying the field evidence, the Bureau concluded that the vein merited further exploration, particularly at a depth of about 440 feet, where the Fredonia limestone would form the foot-wall of the vein and the hanging wall would be the competent Cypress sandstone.Between October 17, 1944, and March 26, 1945, three diamond-drill holes were bored for a total inclined depth of 1,592 feet. Holes 1 and spaced approximately 500 feet apart, explored the vein at 440 feet 4 below the surface. The economic mineralization existed in the vein where cut. Hole 3 cut the fault at approximately 300 feet below the outcrop but failed to find any vein matter except stringers of calcite with small amounts of pyrite."

Apr 1, 1947

By Timothy A. Clancy

To help reduce the Nation's dependence on imported chromite, the Bureau of Mines is conducting research on the use of dolomites as an alternate material. Dolomite is a plentiful domestic resource and offers certain advantages as a refractory raw material. A review of the literature has indicated that there are many sources of high-purity dolomite in this country and that European nations use a greater proportion of dolomite refractories, primarily in steelmaking, than the United States, The Bureau of Mines characterized 14 domestic dolomites as to chemistry, density, mineralogy, microstructure, and thermal behavior, to develop baseline data on their suitability as refractory raw materials.

Jan 1, 1983

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By Heinz W. Sternberg

A method for the electrochemical reduction of the benzene ring was developed and applied to the electrochemical reduction of coal. Successive electrochemical reductions of a vitrain from low-volatile bituminous coal in ethylenediamine saturated with lithium chloride resulted in the addition of 53 hydrogens per 100 carbon atoms. Ultimate analyses and pyridine solubility of the vitrain recovered after each reduction showed that hydrogen added at the beginning has a much greater effect on solubility than hydrogen added at a later stage. Surprisingly, the removal of sulfur from the vitrain takes place only after the more reactive aromatic rings are reduced. Nuclear magnetic resonance analysis and average molecular weight determination of the extracts of the reduced vitrain samples, representing about 18 percent of the vitrain, showed that these fractions had 95 percent of their hydrogen content on saturated carbon atoms and an average molecular weight of 800 to 900. A study of the effect of operating variables on current efficiency showed that current efficiency is highest with aluminum as cathode material and with lithium chloride as electrolyte. A substantial increase in current efficiency of difficulty reducible olefinic double bonds was achieved by adding a proton donor. This result is significant in connection with the electrochemical reduction of coal which proceeds from readily reducible aromatic double bonds to difficultly reducible isolated double bonds. It is proposed that reduction is achieved by electrolytically generated and subsequently solvated electrons and hence does not require prior adsorption of the substrate at the electrode surface. This offers a distinct advantage for electrolytic reduction of sparingly or insoluble substrates such as coal.

Jan 1, 1967

By L. P. Purtell

The performance of ten anemometers of several types has been measured at low air speeds. Multiple calibration runs provided sufficient data for measuring random error about the mean calibration curve in addition to the difference between indicated and true speeds. Measurements were also performed of the minimum operating speeds of the anemometers.

Jan 1, 1979

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

By John Nagy

Large-scale tests in the U.S. Bureau of Mines Experimental Coal Mine show that the explosion hazard of coal dust on shuttle-car roadways can be con-trolled by proper application of water, dry rock dust, a saturated solution of ammonium phosphate, or mixtures of water or the water-phosphate solution with rock dust. The experiments were made with loadings of 1.0 and 5.0 pounds of mine size coal dust per linear foot of entry, and with a 3-or 4-inch-thick layer of coal rubble on the floor, The data from the tests with mine-size coal and rubble are comparable. The water contents of the dust loading were determined from samples collected just prior to initiation of a gas-air mixture in an ignition zone at the face Dust samples were collected 1 inch deep from the coal-rubble deposit. One experiment was made with the dust in the coal rubble bound with latex applied as a water solution by spray. The binding action was inadequate and explosion propagation was obtained.

Jan 1, 1970

By Ernest W. Loya

The Bureau of Mines has developed a computer program for calculating the composition of gravimetric primary standard gas mixtures. The Fortran IV program applies corrections due to buoyancy variations of the cylinder and inaccuracies of the balance weights. The program also determines the statistical error due to the sensitivity and precision of the balance and applies the analytical error of the weighed gases.

Jan 1, 1985

By Y. Miron

'This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, g the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2).

Jan 1, 2010

By D. E. Wolfson

This report presents 900° C BM-AGA carbonization and related data for coals from the principal beds of Nicholas, Randolph, and Webster Counties, W. Va. Thirty-three samples from nine coal beds in three counties were car-bonized at 900° C in the l8-inch-diameter BM-AGA retort, data from which have been correlated with industrial production. Host of the samples were chemically suitable for metallurgical use, and their coking properties were satisfactory. Except for four of the Lower Kit-tanning samples, the ranges of constituents in the coal seams were 1.8 to 9.0 percent ash and 0.4 to 1.1 percent sulfur, values within the range of accept-ability for metallurgical coals. Coke strength indexes were normal for Appalachian coals of similar rank, and the tumbler stability indexes of the coke ranged from 35 to 57.

Jan 1, 1969

By Marilyn Biviano

This analysis was conducted in response to concerns raised by the Chairman of the Energy and Commerce Committee of the House of Representatives regarding the potential impacts on automobile production, GNP and employment resulting from embargoing south African supplies of the platinum-group metals, platinum and rhodium. This analysis should be considered an addendum to the recently released study in which the direct economic costs I of a U.S. embargo on selected South African strategic and critical materials are estimated. The estimated GNP and employment impacts result when a mineral shortage reduces domestic industrial production and are in addition to the direct costs estimated in the earlier study. The direct cost to this nation resulting from a decision to embargo six south African strategic and critical minerals was estimated at $1.85 billion per year during the 1988-1992 time frame of the study. The estimated direct costs include the costs to U.S. consumers resulting from higher strategic mineral prices, lower mineral consumption, and the cost of developing higher cost domestic mineral resources. A large proportion of the costs result from the shortage of the two metals: platinum and rhodium. The average direct annual cost of embargoing is estimated at about $1.4 billion for platinum and $384 million for rhodium.2

Jan 1, 1988

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted.

Jan 1, 1966

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support given through cooperative agreements by the following organizations to investigations con¬ducted by the Explosives Research Center during fiscal year 1965: Dow Chemical Company Manufacturing Chemists' Association Monsanto Chemical Company The Sulphur Institute

Jan 1, 1966

By R. Havens, B. K. Shilber

"INTRODUCTION In the course of the investigation of the occurrence of manganese deposits in the western United States, ore-dressing tests were made on three samples procured by Bureau of Mines engineers from two properties in southeastern Juah County, Utah, each of which is known by the name Black Jack. To avoid confusion, the tests will be described under the names of the owners Kendall-Duvall and the Empire Mines.None of the samples were amenable to ore dressing for the production of high-grade manganese sinter.Ores from the Kendall-Duvall deposit represent an interesting metallurgical phase of low-grade manganese occurrence, as the occurrence of manganese as silicate (braunite) automatically governs the extent to which they can be beneficiated by mechanical methods of treatment. As less than 50 percent of the total manganese was recoverable by complex methods of treatment in a 40- percent-manganese sinter, attempts were made to recover most of the manganese in a low-calcite, intermediate-grade product that might be acceptable for subsequent metallurgical treatment. By selective flotation of calcite and manganese, up to 68 percent recoveries were obtained in plus 20-percent manganese products..No encouragement can be given for successful ore-dressing of Empire ores as represented by samples received for testing, as no products were obtained that would meet minimum marketing specifications. Empire ore contained only 1 percent lime and might be high enough in grade (19 percent manganese) for direct hydrometallurgical treatment."

Nov 1, 1947

By T. F. Mitchell, Walter J. Long

"SUMMARYThis report is one of a series giving results of laboratory and pilot-plant investigations of the concentration of western manganese ores begun in December 1940. Data given summarize results of laboratory investigation of three samples of complex oxide manganese ores from the Madeline property, Lake View, and Victory claims, Clallam County (Olympic Peninsula), Wash. The samples represented an extremely intimate and complex association of manga¬nese oxide minerals with silica and iron.Owing to the complex nature of the ores, no effective concentration by ore-dressing methods was possible. No high-grade manganese concentrates were produced and the highest recovery at minimum accountable grade was only 55 percent on one of the ores tested.Since the Clallem County ores did not respond to ore-dressing methods, leaching processes were investigated, results of which are to be published in a separate report.INTRODUCTIONOre-beneficiation tests were conducted on three samples of manganese oxide ere from the Madeline, Lakeview, and Victory claims, Clallam County, Wash. The ores are extremely complex because of the unusually small size of manganese mineral particles, their mode of occurrence, and relationship to the gangue. None of the three ores was amenable to the production of high-grade manganese products by ore-dressing methods."

Dec 1, 1945

1.0 SCOPE AND REGULATIONS 1.1 This specification covers the minimum requirements for material handling and associated equipment including design and materials. 1.2 This specification requires compliance with all federal, state, local laws and regulations which may be applicable including the Occupational Safety and Health Act, Construction Safety Act as well as rules, regulations and standards of the Secretary of Labor.

Jan 1, 1979