Search Documents

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting &, Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. W. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K. Thomson, W. G. Derby, and the assistants of the writer, K. W. McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the a. id of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate any one method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

By G. Andrews

This case study details the process that was used for project planning and permitting for the Greens Creek Mine, located near Juneau Alaska, as seen through the eyes of one of the primary environmental consultants. This case shows how a Company could involve the public and the agencies in the early 1980's and develop a project sensitive to concerns expressed with a high level of environmental protection. Comparisons are made to the current environmental permitting situation. Initial baseline studies performed during the exploration phase provided helpful information for more detailed environmental work in 1980-1981 as planning and permitting formally got underway. Since the mine was in a National Monument and abuts up to a designated wilderness, the Monument Manager administered the project for the lead agency, the USDA Forest Service. Planning and permitting progressed smoothly to a Final Environmental Impact Statement (FEIS) in 1983. Metal prices were depressed when the FEIS was completed and the project permitting proceeded slowly. Ownership changed several times in the mid-1980's. New owners re-evaluated the project and suggested five changes that required a supplemental EA prior to development. The project was fully permitted and started construction in 1988. Operation began in 1989. Today the environmental process in southeast Alaska is now much more complex, detailed, expensive, and time consuming than in the early 1980's. Significant issues discussed that may impede development and operation include overlapping agency jurisdictions, personal agendas of agency staff, conflicts between agencies that impede project progress, changing regulations, and a well organized environmental opposition.

Jan 1, 1993

By H. M. Lawrence

"The land-pebble district, the larger of the two producing areas of Florida, is situated in Polk County and in the eastern part of Hillsborough County. About 80 per cent at the phosphate rock produced in the United States in recent years has been mined from this area. The phosphate ores, locally termed matrix. are beds of sands and clays containing the phosphate pebbles, considered to be Pliocene in age, derived by marine action from underlying Miocene phosphatic marls, and are covered by practically barren sands and clays that have been deposited more recently. Open-pit mining is practiced; hydraulic mining, which has been intensively developed in this district, is used exclusively for mining the matrix and, by some companies for removing the overburden, although drag-line excavators have become established and are proving economical for stripping operations. From the pits the matrix is pumped to adjacent washing plants for beneficiation. The product of the washers. after drying, enters the world markets as Florida pebble phosphate.In this district recovery of the phosphate pebbles by the washing plants has not been particularly effective in the past. The screening, designed to effect a seperation at about 20 mesh (0.033 inches), has not been well controlled. Washer rejects discarded to the waste dumps have contained appreciable amounts of material analyzing above the minimum commercial grade - 66 per cent B.P.L. (bone phosphate of lime). Such losses of commercial fractions should be considered avoidable, and have been discussed at length in a previous paper.3"

Jul 1, 1930

By William J. Campbell

The purpose of this investigation was to extend the analytical services which are required for Bureau of Mines programs in developing and evaluating high-purity materials. Determination of trace elements in minerals and ores as an aid in geochemical evaluation and prospecting was considered. Serious consideration should be given to the merits of using the avail- able fluorescent X-ray spectrographic instrumentation and techniques for determining trace elements. Limits of detectability for trace elements in metal, oxide, solution or mineral samples range from 0.1 to 100 p.p.m, depending on the element being determined, overall sample composition, and the complexity of the X-ray spectra; limits of detectability range from 0.01 to 1 microgram for elements that have been preconcentrated by a chemical or physical process, for example, by ion-exchange membrane.

Jan 1, 1962

By Linneas W. Laage

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation.

Jan 1, 1995

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By Arnis Mangolds

A study of the technical and economic feasibility of using a unique undercut and fill system developed by USBM engineers to mine steeply pitching coal is discussed. A brief resource assessment has indicated that significant reserves exist in most coal regions to justify the development of a safe and economical method of extracting steeply pitching coal. The undercut and fill system combines hydraulic coal cutting with unassisted gravity fluming of the coal slurry. Mining occurs across strike and the extended entry is backfilled to provide uniform strata control and an impermeable water and air barrier. Subsequent mining occurs beneath the previously filled stope such that the roof consists of a solid, controlled back. In addition to providing positive roof and hanging-wall support, the backfill system eliminates subsidence potential, post-mining drainage, and the danger of spontaneous combustion from naturally drafting air currents. A unique through-flowing ventilation system permits passage of return air through the production face via ducting located at the backfill-coal junction. This provides a constant supply of fresh air at the face, eliminates the need for brattice cloths, and provides an additional escapeway for the miners. The preliminary estimates indicate a production rate in the neighborhood of 31.9 tons/ manshift. Capital costs are approximately $3.17/raw ton over a 20-year life with an initial investment per annual ton of $48.29. Total cash-costs for labor, supplies, power and benefits range in the vicinity of $19.59 for a 704,460 ton/year mine, or a total cost of $22.76/ton. These costs do not include federal and local taxes or post-of-money; however, the cost of coal is well within the area selling price.

Jan 1, 1981

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By Choon Kooi Quan

Water availability is essential for mining and minerals processing. To provide government and industry with recent data for water use planning and management, the Bureau of Mines canvassed a number of U.S. producers of nonfuel minerals to determine their water use in 1984. Data were analyzed and compared with previously published data in order to examine historical trends in water utilization in the nonfuel minerals industry and to estimate water requirements in the year 2000. Total water use in the domestic nonfuel minerals industry during 1984 was estimated at 2,267 billion gal, of which 571 billion gal was new water and 1,696 billion gal recirculated water. The largest users of water were the phosphate rock, iron ore, copper, sand and gravel, and crushed stone industries, together accounting for almost 90% of total used. More than one-half of all water was used in Florida, Michigan, and Minnesota. In the year 2000, total water use will amount to an estimated 2,679 billion gal, of which 810 billion gal will be new water and 1,869 billion gal recirculated water. Most of this water would be used in producing the foregoing suite of minerals,

Jan 1, 1988

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By Mary Cocklan-Vendl

Regulatory processes associated with development of a world class lead-zinc mine, Red Dog Mine, in northwestern Alaska were reviewed and evaluated. Informal interviews with key project personnel, consultants, and agency field and permitting specialists provided perspective on the regulatory successes and failures of the project. Due to potential impacts to air quality, water quality, wetlands, and National Park lands, an Environmental Impact Statement was required. By developing a comprehensive baseline of information on the existing environment to aid in minimizing impacts during project siting/design and through regular coordination of evolving project plans with regulatory agencies, the mine developers were able to acquire necessary permits in a timely and cost effective manner. The only major exceptions occurred when inadequate information was collected on dispersal of airborne particulates, rates of surface water run-off, and groundwater quality. These deficiencies resulted in the need for design changes, unscheduled construction, additional environmental monitoring costs, and delays in issuance of the NPDES permit.

Jan 1, 1992

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941