Search Documents

By Homor N. McDonald, G. Dale Coe, Will H. Coghill

"INTRODUCTION Sporadic beneficiation tests have been made on the Birmingham (Ala.) red iron ores for the last 55 years. Now, gravity-concentration plants are in operation, of tables are in use. A major problem, as seen by the present writers, is to obtain a coarser concentrate and add to the recovery without increasing the quantity of slime. The oily practicable solution found so far is to recover, by means of concentration (hydraulic) classifiers, the coarse concentrate normally lost in the table middling and, by a similar method, to recover middling particles from the table tailings The size and shape of the coarse concentrate Particles combine to cause them to report in the table middling rather than in the table concentrate. Similarly, mineral is lost in the tailing. Because of this, the nature of the ore, the deportment jerking table, plant tests on classifiers and tables, and the suitability of small concentration classifiers to treat table zonal middlings are discussed herein.The work was done by the Southern Experiment Station, Bureau of Mines, in cooperation with the University of Alabama, Tuscaloosa, Ala."

Jan 1, 1935

By R. R. Sayers

That the maintenance of proper air conditions is a most important factor in the control of occupational hazards is shown by the large amount of material presented each year through the technical journal's on the effects on workers of injurious dusts, gases, and variations in temperature and humidity.. SUMMARY OF RECENT LITERATURE ON EFFECTS ON WORKERS OF EXPOSURE TO DUSTS The subject of the control of dust and dust diseases continues to be a matter of serious concern in most of the industrial countries of the world, as indicated by the following summary of reports published in a number of foreign countries as well as in the United States. Australia. The Workmen's Compensation Act of 1920 for New South Wales3 provided for the promulgation of schemes for the compensation of workers dis- abled by silica or other dust. In 1924 the prevalence of silicosis and tuberculosis among Sydney stonemasons, quarrymen, sewer miners and rockchoppers was investigated by a Technical Committee of Inquiry, appointed upon the recommendation of the New South Wales Board of Trade. The findings of this committee were published by the Government in 1925. No scheme was promulgated by the Government and in 1926 the Act was amended limiting its scope to workmen disabled by disease caused by silica-dust. This was promulgated and gazetted on September 16, 1927, and applies to men working in sandstone as stonemasons, quarrymen, rockchoppers, and sewer miners in the County of Cumberland.

Feb 1, 1931

By H. W. Davis, W. W. Adams, O. E. Kiessling

"Current economic problems frequently have focused attention upon the lack of adequate quantitative information indicating the relationship between human effort and output in various branches of the mineral industry. With the exception of complete records covering coal mining, only scattered information on the units of human energy required to produce a unit of raw material is available for most of the important industrial minerals. Fortunately a virtually complete statistical record is available covering this phase of the iron-ore mining industry.For many years iron-ore mining companies, whose interest in safety work is well-known, have reported annual data on employment to be used in the compilation of accident statistics. These data on hours of labor and other detailed employment information have been correlated with the statistics on production also reported annually by producers. The outstanding trends shown by this composite record for the 10-year period 1923-32 are included in the following discussion, supplemented by a summary table that presents the principal statistical background of the study. 5The substantial reduction in the number of men needed to produce the annual iron-ore requirements of the United States, as shown strikingly in the graphs, illustrates that in iron-ore production improvements in technology have been consistently winning a battle over the difficulties of nature. In 1923, for example, 41,294 men working 107,551,244 hours were required to produce 69,351,442 gross tons of merchantable ore, equivalent to an average output of 0.645 ton per man-hour. In 1929, however, only 30,763 men working 77,111,686 hours 'zero required to produce 73,027,720 tons of merchantable ore, equivalent to an average output of 0.947 ton per man-hour. Thus, from 1923 to 1929 the average number of men working decreased 25.5 percent and the total man-hours worked 28.3 percent, while the average output per man-hour increased 46.8 percent and total merchantable ore production 5.3 percent."

Feb 1, 1935

By G. B. Shea

The accident experience of the California petroleum industry for 1927 was characterized by a decrease it .the number of fatalities. The year closed with a total of 41 fatal accidents, as compared with a total of 54 for the preceding year. 3 In percentage, the figure for 1927 represents a decrease of 24 per cent from that of 1926 and evidences the promising results of organized safety work, in which the industry in California has taken an absorbing interest. The percentage of decrease for 1927 is the largest recorded in any one year since the compilation of the fatality record in the California petroleum industry was begun. Although good progress has been made during the past few years, much remains to be done to reduce still further the human and economic waste caused by accidents. This review is intended to show the employee, as well as the employer, the proximate and contributing cause of accidents. To increase the value of the report, preventive measures in various instances are suggested, on the theory that accidents of a similar nature will occur unless remedial action in taken to remove the cause.

Jan 1, 1928

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

This report is a proceedings of a briefing recently sponsored by the Bureau of Mines at which Bureau personnel presented findings from their research efforts to improve steelmaking techology currently used in the United States. The papers contained in this report address many areas of concern to the iron and steelmaking industry. Among these are improving arc stability in electric arc furnaces, preheating ferrous scrap to reduce energy consumption, fluorspar substitutes in steel-making, basic steelmaking refractories, corrosion of iron-based materials, improvements in stainless steel acid pickling processes, recycling of stainless steel dusts and other wastes, and use of wastes as a source of zinc for electro/galvanizing.

Jan 1, 1988

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By Michael Rieber

In this study a generalized specification and costing model for high tonnage coal carrying conveyor belts of 3.5 to 100 miles is presented. These belt systems, in modular units or flights, of up to 9 miles in length can be considered in terms of gathering systems. The study format is sufficiently open to allow users to insert their own requirements and parameters. A specific case study is provided. Because conveyor belts are feasible almost anywhere, this study has not investigated any specific route or geographic location. Rather, it has concentrated on setting up an heuristic programming model for conveyor belt facility optimization and cost minimization. The analysis starts with the principle factors involved in the design of the system and their optimization for various cases. This is followed, in Section 5.4, with a factor by factor cost analysis based on industry data and the preceding optimization. The next step is the development of both facility and costing models suitable for computer analysis. Logic flow diagrams are presented at each major analytic step.

Jan 1, 1977

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

By W. W. Adams

"The main purpose in the compilation of accident statistics is to reveal conditions that may result in injury to persons or property so that remedial measures may be applied. For practical reasons it is usually found necessary to restrict inquiry to conditions which actually have caused personal injury, and to omit those which nay, but have not yet, resulted in damage, Fortunately or unfortunately, there is a sufficient number of the former to indicate the existence of hazards so numerous as to require all of the attention which the industry can devote to the subject.Two years ago, the Bureau of 'mines, in cooperation with the National Safety Council, undertook an intensive campaign to obtain more complete and satisfactory information regarding mine accidents than had theretofore been available. Since 1911 the bureau had been receiving annual summaries from all companies operating metal mines, showing, in a general way, the number and causes of accidents that occurred during the preceding year and the number of men employed at the mines. Monthly summaries of fatal accidents at coal mines were received from the state inspectors, showing the number of deaths attributed to each of 22 main causes of accidents, Information for individual coal mines was not furnished.While this information, nation-wide in scope, is indispensable because it epitomizes the progress or retrogression in the industry as a whole, and serves as a background of specialized studies, yet certain classes of acci¬dents, for example, those that are more or less peculiar to specific districts or mines, require an analysis in greater detail than is possible on the sole basis afforded by the annual summaries.The need for more specific information was realized some years ago in the State of Pennsylvania in connection with the administration of the workmen's compensation law, The mining industry is well acquainted with the val¬uable studies of accidents, particularly nonfatal accidents, in the mines of that State being conducted by Mr. Rush N. Hosier."

Sep 1, 1924

By E. J. Matson

"The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties.A preliminary examination of the Mount Hope mine was made in January 1943 by the Bureau's engineers, who recommended exploration by diamond drilling.The mine is in the unsurveyed portion of T. 22 N., R. 1 E., Mount Diablo base and meridian, south-central Eureka County, Nevada, 25 miles by road north of the village of Eureka. A partly graded and Graveled secondary road connects the mine and Eureka on U. S. Highway 50.Extensive sampling was done by the Bureau in February. 1943. Core drilling from the surface was started on March 15, 1944, and completed on April 2, 1545. The 16 holes drilled totaled 7,215 feet. The mining company also did extensive underground core drilling from April 21, 1944, to January 4, 1945. This report gives the results of core drilling supervised by the Bureau of Mines.The drilling program was designed to explore for extensions of the mineralization exposed in the mine workings. As a result of drilling, additional ore was found, and it is believed that this project has fulfilled the purpose for which it was planned.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization, of our mineral resources to the end that they make the greatest possible contribution to na¬tional security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation test. Both these branches are under the supervision of Dr. R. S. Dean, assists director.With respect to this report special acknowledgment is due to Charles W. Merriam of the United States Geological Survey for his interpretation of the Mount Hope mine Geology and his cooperation throughout the project; Col. Leverett Davis, former lessee of the property; K. K. Hood, manager of the Mount Hope Unit, Callahan Zinc-Lead Co., Inc.; C. P. Knaebel, assistant manager, and M. P. Nackowski, geologist, of that company, for their help, and to the Sullivan Machinery Co. for its assistance."

Aug 1, 1946

By Samuel P. Polack

This report reviews investigations to determine the fire hazard in coal mining when using flammable petroleum hydraulic oils to actuate mining equipment and summarizes research by the Bureau of Mines and industry on fire-resistant hydraulic fluids. Tests were established to evaluate fire resistance and the necessary characteristics to assure adequate service when fire-resistant fluids are used to replace petroleum hydraulic oils. The research was conducted in the laboratory and field trials under actual operating conditions in underground mines. Bureau of Mines Schedule 30 became effective December 17, 1959; the first approval was granted on February 18, 1960, and the twelfth was granted on March 17, 1961. The approvals include nine ready-mixed (by the producer) fluids and seven concentrates to which water is added by the user according to instructions from the producer. Seven synthetic-type fire-resistant hydraulic fluids submitted by two producers are also approved. Over 100 coal mines are now using water-in-oil emulsion-type fire-resistant hydraulic fluids in varying degrees from a trial in one machine to all the hydraulic equipment in an entire mine.

Jan 1, 1961

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By John W. Taber

"INTRODUCTION AND SUMMARYDiscovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits, appear to be sharp-walled, low-angle, tabular ore bodies in granite and are at least 10 feet thick.The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaFp and 1.44 percent SiO2.Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3."

Oct 1, 1952

By S. L. Windes

This report presents a tabulation of the physical and petrographic properties of Over 100 rock types from operating mines or mineral-investigation projects. The physical properties include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength, (modulus of, rupture) Impact toughness Abrasive hardness Scleroscope hardness Modulus of elasticity (Young's modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1949

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By E. L. Garton

The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying southwest of the Arbuckle Mountains. It includes six counties: Cater, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvanian age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.

Jan 1, 1941

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952