Search Documents

By H. Tomlinson

"INTR0DUCTIONThis publication is a third of a series devoted to falls of roof and coal in coal mines of the Western States. It gives the results of examinations of the mines of the Rock Springs coal District of Sweetwater County, Wyo., which represent the principal coal beds therein and approximately 75 percent of total production of the State.A study was made of safety conditions at all the producing mines of the district and suggestions were offered the operators regarding methods and practices which would, in the opinion of the writer, provide additional safeguards to prevent accidents from falls of roof and coal.In presenting the subject, consideration must be given to such features as character of the coal beds, depth of cover. methods of mining, timbering practice, roof testing and supervision, and for comparative purposes to certain statistical matter bearing upon relation of accidents to their causes, tonnage produced, men employed, days worked, and lost days due to accidents during the 3—year period covered by this study.ACKNOWLEDGMENTSThe writer acknowledges the cooperation of the officials of the various coal companies, without whose assistance this work could not have been completed.F0UR REPRESENTATIVE COAL OPERATIONSThis report relates to four representative coal operations in the Rook Springs district of Sweetwater County, Wyo., which are referred to as mines A, B, C, and D. This group employs yearly an average of 993 men, representing 37 percent of the men in coal mines of the county, and has an average annual production of 1,484,373 tons, representing approximately 44 percent of the coal produced in the county. Figure 1 is a map of the Rook Springs coal district."

May 1, 1933

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption if this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 mill ion tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably are in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Jeffrey P. Schubert

The study site in northeastern Illinois underwent surface mining for coal in 1943 and was reclaimed by the state of Illinois in 1972-1973. Additional soil amendments and seed were applied to the spoil surface in 1975-1980. Previous studies in 1975-1978 had shown that the surface spoil materials and five final-cut lakes at the site were quite acidic and the lakes contained high concentrations of sulfate and dissolved metals. Surface runoff water from monitoring plots in 1976 were only moderately acidic and the mean concentrations of most dissolved metals and sulfate in the runoff waters were less than 25% of the concentrations found in Lake B. By 1980, vegetation had become well established over most of the mined area. However, the five final-cut lakes (Lakes A-E) remained acidic. The purpose of the study reported here was to determine the physical and geochemical subsurface conditions of the spoil materials, the hydrologic flow system within the spoils, and the magnitude of acidic spoil leachate migration into the lakes and into the wetland prairie north of the mine site. Lakes A, B, C, and E were still very acidic in 1980-1981 (pH range: 2.9-3.4; aridity range: 110-860 mg/L as CaCO3). Lake B had the worst water quality, with mean concentrations of dissolved aluminum, iron, manganese, and sulfate of 75, 25, 37, and 3340 mg/L, respectively. Shallow groundwaters in spoil materials around Lake B had a lower pH and about two to four times greater concentrations of aridity, aluminum, manganese, zinc, and other metals and nearly 20 times greater dissolved iron than the water in Lake B. The shallow groundwaters in undisturbed soils and bedrock 10-30 m north of the mine site spoils generally were alkaline, but did contain occasional moderately high sulfate and metal concentrations. Pumping tests and recovery tests conducted in piezometers showed hydraulic conductivities of spoil materials ranging from less than 10- to 10-5 m/s; hydraulic conductivities of natural soils and bedrock were measured between 10-10 to 10-7 m/s. Water levels in spoil materials increased rapidly in response to rainstorm events and the recession curves were relatively quick to decline, lasting only two or three days. Quick infiltration of rainfall into the spoil surface and percolation down to the water table caused a rise in groundwater levels and movement of spoil groundwater into the lakes. This groundwater component in the lake water budgets could account for most of the water quality problems occurring in the acid lakes.

Jan 1, 1984

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The ;purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of mining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENTS The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

By R. G. Gürtunca, J. A. Breslin

This paper briefly describes the progress in mine safety in the United States, with emphasis on recent events that have followed since the explosion at the Sago Mine in January 2006. Legislation following the mine accidents last year and areas of work carried out by the National Institute for Occupational Safety and Health (NIOSH) related to the accidents are discussed. American coal production in 2006 was 1,150 million short tons. Most of this coal is consumed domestically, with annual exports of coal about 50 million tons. One third of annual production is produced at surface mines and the rest from underground. This coal is produced by about 82,000 miners working at 1,400 coal mines. Major improvements in coal mine safety have been made in the US since the Federal Mine Safety and Health Act of 1977. The fatal injury rate in underground coal mines between 1977 and 2004 was reduced by 47.8% to 0.036. The annual number of fatalities dropped from 112 to 14 during that period. Likewise, the non-fatal days-lost injury rate was reduced by 42.6% from 10.87 to 6.24. The improvements in mine safety during this period can be seen in the graph of underground coal mine explosion fatalities and injuries from 1980 to present, which is shown in Figure 1. Between 1984 and 1993 (9 year period) there were 5 explosions and one major mine fire, for a total of 55 fatalities. Over the seven year period from 1993 to 1999 there were no fatalities from coal mine fires and explosions. However, in the six years since 2000 there have been 5 explosions and one fire, which have caused 37 fatalities. [ ]

By C. M. Harrer

The location, features, quality, and extent of iron ore deposits are evaluated in this Bureau of Mines report. The results of pioneer beneficiation on Wyoming taconites and their success are discussed along with developments in the iron-ore mining industry, markets, and economics. Market potential, transportation, resource developments, taxation, cost of iron ore enterprises, and the future of Wyoming iron resources are evaluated. Although occurrences of iron ores in Wyoming were known prior to 1870, early production to 1900 was as a nonferrous metallurgical flux and as mineral pigment for paints. In 1901, the Hartville-Sunrise hematite deposits were available to the Western iron and steel industry and in 1962, the first western taconite operation was placed in production at Atlantic City, Wyo. This investigation disclosed the probability of other large iron deposits in Wyoming. Taconite in the Bradley Peak area of the Seminoe Mountains has a potentiality of 100 million tons; that in the Owl Creek Mountains may prove very large also. Pioneer beneficiation testing has been included, and results have been generally encouraging. Research continues on the large titaniferous magnetite deposits of Albany County, Wyo. At present high-density titaniferous magnetite is being mined and processed at Iron Mountain for heavy-aggregate and as a sized coating for underwater pipelines. Ample mineral raw materials needed for mining and processing Wyoming iron ores are available. Investments for iron-ore processing plants will generally be large, particularly for taconite and titaniferous magnetite.

Jan 1, 1966

By C. M. Harrer

The location, features, quality, and extent of iron ore deposits are evaluated in this Bureau of Mines report. The results of pioneer beneficiation on Wyoming taconites and their success are discussed along with developments in the iron-ore mining industry, markets, and economics. Market potential, transportation, resource developments, taxation, cost of iron ore enterprises, and the future of Wyoming iron resources are evaluated. Although occurrences of iron ores in Wyoming were known prior to 1870, early production to 1900 was as a nonferrous metallurgical flux and as mineral pigment for paints. In 1901, the Hartville-Sunrise hematite deposits were available to the Western iron and steel industry and in 1962, the first western taconite operation was placed in production at Atlantic City, Wyo. This investigation disclosed the probability of other large iron deposits in Wyoming. Taconite in the Bradley Peak area of the Seminoe Mountains has a potentiality of 100 million tons; that in the Owl Creek Mountains may prove very large also. Pioneer beneficiation testing has been included, and results have been generally encouraging. Research continues on the large titaniferous magnetite deposits of Albany County, Wyo. At present high-density titaniferous magnetite is being mined and processed at Iron Mountain for heavy-aggregate and as a sized coating for underwater pipelines. Ample mineral raw materials needed for mining and processing Wyoming iron ores are available. Investments for iron-ore processing plants will generally be large, particularly for taconite and titaniferous magnetite.

Jan 1, 1966

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939