Search Documents

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By Clive Ellis, Brian Davies, Steven E. Mischler, Jon C. Volkwein

A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclusion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air. A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclu­sion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air.

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Lin-Ling Zhang, Ji-Geng Yan

This experimental study was done to determine pathological feature of vibration injury to the peripheral nerves in the hind limbs of rats exposed to 7 days of vibration. Materials and Methods Animals: Twenty four male Sprague-Dawley rats weighing 350-400 grams were randomly divided into two groups: sham control group and vibrated group. To document vibration-induced changes in the experimental model, the sciatic nerve was used because it contains both motor and sensory fibers and is relatively superficial in the posterior thigh. Customized Vibrating Platform: The hind limbs of the rats in the vibrated group were exposed to vibration in a custom-built vibrating apparatus consisting of two platforms: a smaller vibrating platform on which the hind limbs of the rat are secured, and a larger platform on which the remainder of the body rests. The vibration parameters (frequency 43.5 Hz, amplitude 1.5mm, acceleration 4.75G, velocity 6cm/sec., and displacement of 3.0mm) of this model were measured. Methods: Rats were anesthetized with 35mg/kg of intraperitoneal Nembutal (phenobarbital) and their hind limbs fixed to the vibrating platform by Velcro loops. Both hind limbs rest on the vibrating platform while the remainder of the body rests on the larger platform. The rats were vibrated 4 hours a day, for 7 days, with close monitoring of the vibration parameters. The 4-hour duration of hazardous vibration was based on recommendations from the British Standards Institution. The sciatic nerve of rats not exposed to vibration, but similarly anesthetized and secured to the vibrating platform, acted as controls. At the end of seven days of exposure to vibration, nerves from both the vibrated rats and the control rats were harvested after perfusion of the lower half of the body using glutaraldehyde as described below. Neural Fixation: The aorta was cannulated, and the inferior vena cava was nicked and the animal was initially perfused with 0.9% buffered sodium chloride. This was followed by perfusion of a filtered mixture of 3% glutaraldehyde and 3% paraformaldehyde fixation solution, The tissue was subjected to post fixation by routine. The neural tissue was then submitted for light and electron microscopy. Results While light microscopy showed minimal histological differences between vibrated (n=12) and control nerves (n=12), the changes revealed by electron microscopy were dramatic. These included thickening of the epineurium, as well as thickening of the myelin sheath as compared with normal nerve. Also, the axon plasma was detached from the myelin sheaths, and many vacuoles were seen between the myelin laminae(Fig.1); These changes were found in all vibrated animals, and in the whole segment of each vibrated nerve. Myelin balls, consisting of

Jan 6, 2006

By F. Matanzo

[Nine wire rope terminations were pull tested and fatigue tested to destruction to measure the termination efficiency and relative fatigue life. The terminations were selected on the basis off mine site visits and the specimen were assembled in a manner similar to industrial slings. To measure a termination's sensitivity to poor workmanship, both standard and modified assembly specimen were tested. Lang and Regular construction of the 6x19 and 6x37 class wire ropes were used in diameters of 13 mm (1/2 in.), 19 mm (3/4 in.), 25 mm (1 in.), 38 mm (1 1/2 in.), and 51 mm (2 in.). In static pull tests rope class, construction, and diameter interacted with the termination to influence the efficiency of the termination. In axial fatigue tests using only the 6x19 class rope, the effect of rope construction was negligible since failure was primarily dependent on the termination type. The Swaged Socket, a termination requiring a high capacity hydraulic press, gave the best overall performance in terms of efficiency and fatigue life. The short body length of the Zinc Poured Socket (RR-S-550) was attributed with the short fatigue life of this termination. The use of thermosetting resins as a replacement for zinc was demonstrated successfully for some socket designs. The fatigue life of the termination, expressed as a percentage of the fatigue life of the wire rope, was shown to be a guide for the retirement of the wire in these applications where the wiry' rope is primarily in axial loading.]

Jan 1, 1978

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976

By N. Grosland, G. Kopp, T. Hunstad, D. Wilder, M. Contratto, S. Rahmatalla, T. Xia

Chronic whole-body vibration exposure, as expected in large construction and mining vehicles, has been associated with neck and back pain and injury.1 While work has been done towards gaining a better understanding of the relationship between vibration and shock and muscle activity of the back musculature2, relatively little information regarding the activity of neck, shoulder and upper arm muscles is known. Today’s equipment designs must conform to domestic and international standards, however these standards do not specifically address the vibration exposure in the head and upper quarter. Further it is not well known how the control configuration within a vehicle (e.g. steering wheel versus arm controls) influences muscle voluntary and reflex activity levels. Greater muscle activity may lead to greater muscle fatigue – which in turn may be associated with greater risk of injury.2 Thus, muscle contractions needed to maintain static postures as well as those resulting reflexively should be considered during an analysis of seating position. Unfortunately, little is known regarding the influence of arm position on head and neck muscle function. The purpose of this study was to investigate the relative muscle activities of 5 neck, shoulder, and upper arm muscles during riding simulations of large construction equipment, using three different arm control options. Methods Five typical heavy equipment ride files were “played back” through a man-rated Servo Test 6-degree of freedom (dof) vibration system. Each ride was repeated using 3 seat and control configurations (steering wheel (SW), floor mounted arm-rest controls (FM), seat mounted arm-rest controls (SM)). Two trials were performed for each ride and seat control combination (each trial: 60 sec of 6-dof and 60 sec of vertical vibration). Five channels of surface electromyography (EMG) of the right-side cervical erector spinae muscles (neck extensors), sternocleidomastoid (neck flexor), upper trapezius (shoulder elevator), biceps brachii (elbow flexor) and triceps brachii (elbow extensor) muscles were collected throughout each ride (~ 2min) using pre-amplified (10x), 1 cm silver bar electrodes, with 1 cm fixed inter-electrode distances (Delsys, Inc). Further analog amplification was set at 10k (1k for one subject), and sampled at 1000Hz using a 12-bit DAQ card and Labview 7.1 software (National Instruments). A total of 7 right-handed male subjects were tested, but only 5 had complete EMG data sets to analyze for this sub-study. EMG was analyzed using root mean square (RMS, in mV) of 20 ms moving windows, and then averaged across the entire trial for a measure of mean total muscle activity (voluntary and reflexive). The muscle activity to maintain the static posture was estimated as the mean RMS EMG over a 1 sec interval just prior to and/or after completion of the ride. Repeated Measures ANOVAs were used to test for with-in subject differences using a = 0.05.

Jan 6, 2006

By Hisataka Sakakibara

Although the pathophysiology of vibration-induced white finger (VWF) is still under discussion, evidence has been accumulated to understand the underlying mechanism. VWF is pathophysiologically characterized by an enhanced vasospastic response to cold, which can result from an imbalance between vasoconstriction and vasodilation in the digital arteries in response to cold (i.e., vasoconstriction-dominant). The imbalance is supposed to be due to faults in vascular vessels and sympathetically mediated vascular tone. Enhanced vasospastic response to cold Narrowing of arterial lumen with medial smooth muscle hypertrophy. Possible functional factors for enhanced vasoconstriction • Increased sympathetic nervous activity to cold (e.g., norepinephrine) • Increased release of endothelin-1 (ET-1; an endothelial-dependent vasoconstrictor) from the endothelium • Increased reactivity of alpha2-adrenoreceptors to cold Possible functional factors for decreased vasodilation • Decreased release of nitric oxide (NO; an endothelial-dependent vasodilator) from the endothelium • Decreased release of calcitonin gene-related peptide (CGRP; a vasodilatory neuropeptide) from sensory afferents The question is how their interrelations or imbalances among them are Vibration and arterial damage The next question is, how does hand-arm vibration exposure induce such pathophysiological changes in VWF patients? Recent morphological evidence from animal experiments shows that vibration acceleration stress (including shear stress) and smooth muscle contraction contribute to arterial damage of smooth muscle and endothelial cells. The vibration-induced arterial damage is frequency-amplitude-dependent.

Jan 6, 2006

By Jeanne A. Smith, Suzanne D. Smith

Annoyance, fatigue, and musculoskeletal pain have been reported during prolonged exposures to propulsion-generated vibration in military propeller aircraft1. The objective of this study was to determine the vibration mitigation properties of selected seat cushions and the effects of occupant seating posture during exposure to higher frequency multi-axis vibration associated with military propeller aircraft. Methods A Navy E-2C Hawkeye crew seat was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). Six seat pan cushion configurations were tested during exposure to an E-2C vibration signal collected in the field1. Seat pan cushions 1 – 5 were used with the original E-2C seat back cushion. Cushion configuration 6 included seat pan cushion 5 with a prototype seat back cushion. Triaxial accelerometer pads were mounted onto the seat pan and seat back cushions to measure the vibration entering the human. Data were collected for seven subjects seated upright with their backs in contact with the seat (back-on) and not in contact with the seat (back-off). Spectral analysis techniques were used to analyze data at the two dominant frequencies associated with the propulsion system (propeller rotation frequency (PRF) ~18.5 Hz, and blade passage frequency (BPF) ~73.5 Hz). Overall accelerations were also calculated between 1 and 80 Hz. Vibration Total Values (VTVs) were calculated using the weighted seat pan and seat back (back-on only) accelerations and compared to the comfort reactions given in ISO 2631-1: 19972. Results In general, the highest accelerations observed at the seat pan occurred in the fore-and-aft (X) direction at both the PRF and the BPF for all cushions and both postures. The most pronounced effect was at the BPF in the X direction, where all configurations showed significantly lower seat pan accelerations than configuration 1 (original E-2C cushion) with the back-on posture. Configuration 5 was the exception with the back-off posture (Fig. 1A, Repeated Measures ANOVA, P<0.05). The most pronounced effect of posture occurred at the PRF in the X direction, where all cushion configurations showed significantly lower seat pan accelerations with the back-off posture (Fig. 1B). All configurations except configuration 2 showed similar VTVs as compared to Configuration 1 (Fig. 2, P<0.05). Configuration 2 tended to show the lowest weighted acceleration levels. The overall VTVs (back-on only, Fig. 2B) showed significantly higher accelerations as compared to both the back-on and back-off seat pan point VTVs (Figs. 2A &

Jan 6, 2006

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By C. E. Julihn, Lowell B. Moon

"INTRODUCTION To increase the supply of ore needed to produce steel the Bureau of Mines has explored 187 mineral deposits containing chromium, iron, manganese, cobalt, nickel, fluorspar, tungsten, vanadium, or coal during the fiscal years. 1940-44, the deposits thus explored were selected from several thousand that were first examined to appraise their possibilities. The objective of the exploration was to determine the tonnage and grade of ores upon which mining, operations might be based, and the metallurgical processing that was most suitable for their utilization.Most of these deposits were sub-marginal by pre-war standards; hence there had been no incentive for their exploration, yet many such deposits were known to exist that probably contained ore sufficient in grade and amount to be utilized as war reserves.Some of the Bureau's exploration projects have disclosed substantial or even very large amounts of ore, much of which is fairly high in grade. In a few of them bodies of high-grade ore have been found, though in others the tonnage has proved to be too small or too low-grade for utilization."

Mar 1, 1945

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

By D. E. FOCG, A. E. Wells

When the United States entered the World War governmental agencies found little definite knowledge available as to the exact capacity of each sulphuric acid plant in the United States to manufacture acid under the stress of a great emergency. It is true that on account of the demand for acid for the manufacture of munitions for the Allies, prior to the entrance of this country into the war, most of the acid plants near industrial centers in the Eastern and Northern States were running at or nearly their maximum capacity, but, . for various reasons, many plants in these States and plants in other districts were not. For a number of years statistics as to the production of acid by the plants of the country were compiled by the United States Geological Survey, but obviously such figures did not give information as to the maximum capacities that might be available for meeting the he.a vy war ·requirements, or as to the steps that would have to be taken to bt-ing these capacities into use. During the summer and early fall of 1917 various attempts were made to obtain the desired information, but no satisfactory or complete data were obtained. Late in 1917, under the authority granted to the Bureau of Mines by the explosives act, the Director of the Bureau of Mines directed A. E. Wells, metallurgist of the bureau, to uiake a complete survey of the situation. Mr. Wells personally conferred with officials of the acid companies and visited most of the acid plants in the North that are east of the Mississippi River. The information obtained through this personal survey, together with that obtained through the ready cooperation of the subcommittee on ncids, and the subcommittee on fertilizers of the Committee on Chemicals of the Council of National Defense, enabled the preparation of a report containing the desired data concerning the sulphuric acid industry. This report was made immediately available to the War Industries Board and to those offices in the War and Navy Depart- ments that were most directly concerned in planning the explosives program and in obtaining the necessary supplies to produce the explosives. Beginning with this survey and report, the sulphuric acid section of the war minerals investigations of the Bureau of Mines took an active part in all matters pertaining to the sulphuric acid industry during the remainder of the war. Mr. Wells, the chief of the section, was appointed an associate chief of the sulphur, pyrite, and sulphuric acid sections of the War Industries Board. .Also, by this direct contact with the War Industries Board, the data obtained by Messrs. R. R. Hornor, H. A. Buehler, a.nd 0. Lindstrom, who were in charge, for the bureau, of the investigations concerning the supplies of pyrite and sulphur, were constantly made available to all interested Government agencies. D. E. Fogg, of New York City, was appointed chemical engineer to the sulphuric acid section to make special investigations relating to the acid industry, especially the possible utilization, in an emergency, of those sources of raw material.not then being used. Mr. E. E. Corbett, of Brooklyn, N. Y., was appointed chemical engineer to make investigations concerned primarily ,vith the conservation of acid. Direct and intimate contact with the industry was had through the close cooperation with the committee on acids of the Chemical Alliance, this committee during the greater part of 1918 occupying rooms with the acid section of the bureau. With the ending of the war and the close o:f the active work of the acid section of the bureau, the suggestion was made by many interested parties that a bulletin be prepared giving some qf the fun. damental and most important facts regarding the sulphuric acid industry, including a discussion of the technical :features of the manufacture of acid. During the war the bureau received -a vast number of inquiries in regard to various phases of the industry, a.nd this fact also made such a bulletin seem desirable. Therefore, the present bulletin was prepared to cover the main facts in regard to the industry in this country, including a discussion of the supplies of sulphur-bearing raw materials, the situation of the acid plants, the principal points in regard to manufacturing processes, and the uses of the acid. No attempt has been ma.de to discuss at length the manufacturing processes, as details differ more or less at the different plants and in general are carefully guarded by the acid ·companies. A great deal of the data given in this bulletin may be found in various pub]ications, but this is the first publication in which such data have been assembled and made readily available. Most of the data were obtained directly from observation and from cooperating acid companies or from individuals who had been or are now engaged in acid manufacturing and were liberal and generous in making their information available for publication. Care has been exercised to publish no data that were obtained as confidential by the bureau's representatives. The average acid manufacturer may be already more or less acquainted with most of the information presented in this bulletin, yet it is believed that the bulletin will be of value to those who wish to obtain a. general review of the present condition, both the economic and technical, of the sulphuric acid industry in the United States.

Jan 1, 1920

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

The investigations reported herein comprise preliminary studies to evaluate large scale mining systems adaptable to the thicker oil shale deposits in the deeper central portion of the Piceance Creek Basin. The studies include an evaluation of the geology, hydrology and resources of the Basin., evaluation of a potential prototype mine site, synthesis of rock mechanics data on Green River Formation oil shale, selection and preliminary design and cost evaluation of six potential mining systems and a ranking analysis to aid in selecting the most promising system. Results of the ranking analysis indicate the following four systems to be most promising for large scale underground oil shale mining: - Chamber and pillar (using spent shale backfill) - Sublevel stoping with spent shale backfill - Sublevel stoping with full subsidence - Block caving with LHD&apos;s Recommendations for phase II are to investigate the above systems in greater detail, refine present cost data, and perform economic evaluations of oil shale mining using these systems.

Jan 1, 1975

By E. A. Mevissen

With the ever increasing consumption of mineral commodities, the vital question is not whether sufficient mineral quantities will be available, but rather can the known existing low grade resources be mined economically. Conventional conveyor systems are being used in some open pit mines to decrease haulage costs. n an effort, to take this concept one stop further, this contract study examines the use of a high angle conveying system in an open pit mine. It identifies available high angle conveying equipment and examines the haulage and crushing costs associated with both a conventional truck and shovel mining operation and a high angle conveyor operation. These costs analyses were performed on a hypothetical copper, taconite and phosphate mine. Information was gathered from a series of high angle conveying equipment and open pit mining operations in the U.S. Volume I includes a detailed review of the state-of-the-art in high angle conveying concepts, the, hypothetical mine development, and the cost analyses. Volume II includes the appendices.

Jan 1, 1981

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Jesse A. Miller

ALTHOUGH the element titanium was discovered by William Gregor in 1790, over a hundred years passed before it was put to commercial use. The first commercial application of titanium was as an alloy additive to iron and steel, and the first ferroalloys were produced domestically in 1906. Titanium pigments were developed somewhat later and have been produced in the United States since 1918. The use of titaniferous material in welding-rod coatings first gained acceptance ill the mid-30&apos;s. The metal titanium has only had commercial importance since 1948; domestic production for that year was 10 tons. The relative importance of these major uses of titanium in various forms may he gaged by the consumption of titanium dioxide (Ti02) for these purposes in 1954. Of a total of 440,000 short tons of Ti02 consumed in 1954, 95 percent of the total was consumed for pigments; 2 percent for welding-rod coatings; 1 percent for non-titanium-base alloys and carbide; and 2 percent for miscellaneous uses. The titanium-metal industry is in its infancy, but it has more than doubled its output every year from 1948 to 1954, reaching 5,370 short tons in 1954.

Jan 1, 1957

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006